CCH YPS3-14H User manual

说明书
品牌：CCH
印 刷 标 准 颜 色 CMYK 值
10
CMYK:100/50/0/0
CMYK:15/100/20/0
CMYK:0/0/100/0
CMYK:0/0/0/100
江苏友奥电器有限公司
图 样 标 记 重 量 比 例
1:1S A B
设 计 校对1
校对2
日 期
工 艺
审核1
审核2
批 准
谭丽佳 封晓晶 黄檞栋
李玉旺
20210113
许传刚
技术要求：
1.说明书设计尺寸：210×297mm(A4),印刷尺寸：142×210 mm；
2.整本说明书使用105g铜版纸黑白印刷，其他颜色详见内文；
3.必须保证字体按照图纸正确印刷，不得出现乱码现象；
4.纸张边角应裁切整齐，印刷字迹清晰整洁、内容正确，没有明显的拖墨和重影等缺陷；
5.未注公差按GB/T 1804-C标准执行；
变更单号 变更人 变更日期 说明书版本号 变更内容
变更记录：（版本号编码规则：品牌首字母+日期，示例：T20210111）
此页面无须印刷
This page needs no printing.

YPS3-14H
Portable Air Conditioner
User Manual
Thank you for selecting this high quality air conditioner. Please be sure to read this
manual carefully before using it.

Page: 2/14
Content
I. Notes................................................................................................. 3
II. Featuresand Components......................................................... 4
III. Installation and Adjustment.......................................................6
IV. Control Setting.............................................................. .…... . 8
V. Drainage Instructions....................................................................... 10
VI. Maintenance………………………………………………… 11
VII. Troubleshooting............................................................................ 12
VIII. Appendix................................................................................. 13

Page: 3/14
Thank you for choosing the luxurious and elegant mobile air conditioner. Please
keep the manual for later review, and read the manual carefully before use.
I. Notes
Notes:
*The air conditioner is only suitable for indoor use, and is not suitable for other applications.
* Follow local grid interconnection rules while installing the air conditioner and ensure that it is
properly grounded. If you have any question on electrical installation, follow the instructions of
the manufacturer, and if necessary, ask a professional electrician to install it.
* Place the machine in a flat and dry place and keep a distance of above 50cm between the
machine and the surrounding objects or walls.
*After the air conditioner is installed, ensure that the power plug is intact and firmly plugged
into the power outlet, and place the power cord orderly to prevent someone from being tripped or
pulling out the plug.
*Do not put any objects into the air inlet and outlet of the air conditioner. Keep the air inlet and
outlet free from obstructions.
* When drainage hose is installed, ensure that it is properly connected, and is not blocked or
bended.
* While adjusting the upper and lower wind-guide strips of the air outlet, pluck it with hands
gently to avoid damaging wind-guide strips.
*When moving the machine, make sure that it is in an upright position.
* The machine should stay away from gasoline, flammable gas, stoves and other heat sources.
* Don't disassemble, overhaul and modify the machine arbitrarily, otherwise it will cause a
machine malfunction or even bring harm to persons and properties. To avoid danger, if a machine
failure occurs, ask the manufacturer or professionals to repair it.
*Do not install and use the air conditioner in the bathroom or other humid environments.
* Do not pull the plug to turn off the machine.
* Do not place cups or other objects on the unit to prevent water or other liquids from spilling
into the air conditioner.
*Do not use insecticide sprays or other flammable substances near the air conditioner.
* Do not wipe or wash the air conditioner with chemical solvents such as gasoline and alcohol.
When you need to clean the air conditioner, you must disconnect the power supply, and clean it
with a half-wet soft cloth. If the machine is really dirty, scrub with a mild detergent.
*Children shall not play with the appliance. Cleaning and maintenance shall not be made by
children without supervision.

Page: 4/14
II. Features and Components
1. Features
•New look, compact structure, streamlined machine, aristocratic atmosphere.
•Provides cooling, heating (single cold with no such function), dehumidification and air supply
function.
•Has automatic air swing function. The outlet can be covered when the machine is turned off to
prevent dust from entering the unit.
•LCD display control panel. The machine is beautiful and elegant. High-quality LCD
remote control is equipped to facilitate operation. The remote control can be placed on the back
of the body. It adopts a user-friendly remote control storage design.
•Handles on both sides makes unit easy to move or relocoite.
•The rear of chassis provides hooks for the AC cord. This will keep the AC cord safe during
relocation or storage.
•Exhaust air vent is set high to facility assembly and keep the smooth flow of the exhaust hose.
•Air filtration capability.
•Timer switch function. Unit can be set to turn off after so many hours.
•Compressor protection function .During restarting ,the compressor has a three minute delay.
There are other protection functions.
•Patented product, patent No.: CN201330444908.8.

air vent
1
2
3
4
5
6
7
8
-exhaust
Exhaust hose assembly
21Heat preservation sleeve of
exhaust pipe
21

1. Installation:
Warning: before using the mobile air conditioner, keep it upright for at least two hours.
The air conditioner can be easily moved in the room. In the moving process, ensure that the air
conditioner is in the upright position and should be placed on a flat surface.
Do not install and use the air conditioner in the bathroom or other humid environments.
1.1 Install the heat pipe assembly(as shown in Figure 1): The heat preservation sleeve of the
exhaust pipe is placed on the exhaust pipe, and then screw the heat pipe assembly (exhaust
fitting end) into the exhaust on the rear panel (counterclockwise).
1.2 Install the window sealing plate assembly
1). Half open the window, and mount the window sealing plate assembly to the window(as
shown in Figure 2 and Figure 3); the assembly can be placed in horizontal or vertical direction
1.3 Install the unit
1). Move the machine with installed heat hose and fittings near the window. The distance
between the unit and walls or other objects shall be least 50cm (as shown in Figure 4).
2). Slide open the window plate assembly. Adjust their opening distance to bring both ends of the
assembly into contact with the window frame, and fix into place with clip.

Figure 4
Page: 7/14
2）Elongate the hose and snap the flat end of the hose joints into the elliptical hole of the
window sealing plate assembly (as shown in Figure 5 and Figure 6) .
Notes: 1. the flat end of the hose joints must be snapped into place.
2. The hose cannot be distorted nor has substantial turning (greater than 45 °). Keep
the ventilation of the hose unobstructed.
Figure5 Figure 6
Important Notice
The length of the exhaust hose shall be 280~1,500mm, and this length is based on the
specifications of the air conditioner. Do not use extension tubes or replace it with other different
hoses, or this may cause a malfunction. Exhaust must be unobstructed; otherwise it may cause
overheating.
90cm（35.4inch）
50cm（19.7inch）
BEST INSTALLATION

1
Power key
2
Mode selection key
3
Window display
4
Down key
5
Up key
6
Wind speed selection key
7
Timing key
When power is connected to the unit for the first time, buzzer will play power-on music,
and then the machine will get into standby status.
1. Power Key: press the key to turn on and turn off the machine.
4,5. Up Key and Down Key: press the two keys to change the set temperature or timing the value,
operate as follows:
6. Wind Speed Selection Key:
2. Mode Selection Key: when power is on, press the key to switch between cooling →air supply
3. Window display
→dehumidification → heating(single cold with no such function) →cooling →... mode.
1 2 6 73 4
4

7. Timer Key:
During power on, press the key to close timing. During power off, press the key to open timing.
downwards by one hour increments.
Page: 9/14
2. Mode: press the key to switch between cooling, air supply, dehumidification and heating mode.
1. Power: press the key to turn on or turn off the machine.
Instructions of key operation of the high-quality remote control are as follows:
3. Up: press the key to increase temperature and timing set value.
4. Down: press the key to reduce temperature and timing set value.
5. Fan: press the key to select high, medium and low wind speed.
6. Timer: press the key to set timing value.
7. Swing: press the key to turn on the air vent swing. Air flow of the air outlet can blow at different
angles.