Cctung IP 351W User manual

V1.1
User manual
Network Camera
IP321/321W IP341/341W IP 351/351W IP361/IP361W

``
2
CONTENTS
Product Assurance.................................................................................................................3
Approval Information..............................................................................................................4
Infrared Night Vision............................................................................................................... 9
Installation.............................................................................................................................. 10
Connecting the cameras .....................................................................................................10
Camera Search tool Installation & Usage.........................................................................10
Review Images from the Network CAMERA............................................................................16
Introduction of Main page ...................................................................................................... 18
System Setting.........................................................................................................................20
System status................................................................................................................... 21
Network .......................................................................................................................... 21
Local network........................................................................................................21
PPPOE Account Configure .................................................................................23
Wireless Network....................................................................................................23
DDNS Settings......................................................................................................25
UPnP......................................................................................................................26
Camera Settings........................................................................................................... 27
Stream Setup ........................................................................................................28
Night Vision Settings ...............................................................................................30
Multi Device settings............................................................................................30
Alarm Settings............................................................................................................... 32
Motion Detection settings....................................................................................32
Port Alarm..............................................................................................................32
Alarm Management..............................................................................................33
Periodic Record Schedule...................................................................................34
Periodic sending...................................................................................................34
File Store................................................................................................................34
SMTP......................................................................................................................35
FTP.........................................................................................................................36
System Management...........................................................................................................37
Hostname ..............................................................................................................37
User Management........................................................................................................ 37
Time Settings ........................................................................................................38
Disk Management.................................................................................................39
Disk Management.................................................................................................39
Restore...................................................................................................................40
Firmware Update..................................................................................................40
Specification .................................................................................................................... 41
FAQ .................................................................................................................................. 42

``
3
INTRODUCTION
Thank you for your interest and support in our product and purchasing this 3GPP
network camera. The camera can be accessed remotely, and controlled from any
PC/laptop over the Intranet or Internet via web browser. The user-friendly installation
procedure and intuitive web-based interface offer easy integration with your LAN
environment or WiFi system. The camera also comes with a lot of useful alarm tool for
notice user any situation. We feel confident that you will be pleased with the quality and
features of this product.
Notice
This product may cause interferences with other wireless equipment that operates at
2.4GHz ISM band. Please turn off one of the equipments to eliminate the interference.
Product Assurance
This camera will emit electromagnetic wave, just like other wireless products, but its
transmitting power is less than other wireless products such as mobile phones. The
2.4GHz wireless camera meets wireless frequency security standards and
recommended indexes while working. These standards and indexes are certificated by
academic organization and represent the cogitative research of the scientific workers
who continuously explore and annotate the involved fields. So we believe that our
products are safe for customers

4
Approval Information
All our products meet the requirements of approval FCC or CE, and are granted the FCC or CE
certification. They are authorized to bear FCC or CE mark.
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant toPart15of the FCC ruled .These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
radiates radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna
2. Increase the separation between the equipment and the receiver
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
4. Consult the dealer or an experienced radio/TV technician for help
This device complies with Part15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)The device may not cause harmful interference and
(2)This device must accept any interference received, including interference that may cause
undesired operation changes and modification not expressly approved by the manufacturer or
registrant of this equipment can void your authority to operate this equipment under Federal
Communications Commissions rules.
CE
This product complies with standards including low voltage device directive 73/23/EEC,EMC
directive 89/336/EEC and R&TTE directive 1999/5/EC .It passed the subject tests by the
authority concerned and is authorized to bear CE mark.
Restrictions
1. Do NOT use this product to violate one’s privacy. Monitoring one’s activities without consent is
illegal and this product is not designed and manufactured for such purpose.
2. DO NOT put this product near any medical equipment. Radio waves might potentially cause
breakdown of electrical medical equipment.
3.This product should be placed at least 1 foot away from any heart pacemaker .Radio waves
might potentially influence heart pacemaker
4. DO NOT use this product for any illegal activities .It is the user’s responsibility to ensure that
the usage of this camera is of a legal nature

5
Maintenance
1. Ensure that the camera and its power source have sufficient ventilation
2. Do not shake strike or drop the product
3. Keep the camera dry and dustless
4. Do not place the product near any magnetic objects
5. Avoid putting the product in places where there is constant temperature and humidity change
6. Keep the product away from heart sources
7. Do not use the camera near aggressive chemicals
8. Do not use the camera near to water
9. Do not use the camera in the places which are enclosed by metal The surrounding metal may
shield the electromagnetic waves, and result in failure of the signal reception
10. Please obey the local government’s environment protection policy
11. Please turn off the power when left unused
12.Do not disassemble or attempt to repair the camera, doing so might cause damage to the
product

6
MAIN FEATURES
Easy Installation
The camera comes with built-in wireless (IEEE802.11B/G) capability and a web server,
therefore there is no need to install a driver .The setup CD-ROM includes the camera setup
software, user manual and quick installation guide
With industry standard automatic configuration-UPNP (Universal Plug and Play),your PC will
discover and connect to your camera automatically .Once connected ,using a simple web
browser you can see what the camera sees from anywhere in the world !
The camera can be either wall-mounted or ceiling-mounted using the supplied stand. It can
also be placed on a desktop using the supplied stand, thus providing a flexible installation
solution. Quick Installation Guide
Connect
Camera to the
network
Connect DC Power(Wait for Power light to go green)
Connect Ethernet cable from camera to the broadband router
Run Camera
Search to find
Camera on
your network
Run CD ―autorun.exe‖ to install software on a PC connected to the
network
Select ―Tools‖ from the menu
Select ―Camera Search‖ (runs CTVS camera search Installer)
Run Camera Search Program(from the Windows desktop)
Click ―Begin Search‖ (may need to be repeated several times until the
camera is found)
Select the installed camera (high in blue)
Click ―Open device‖ and browser window to the camera will open
Configure
browser to
access camera
Install Active X (may need to change your browser security settings to
allow Active X control to be installed and enabled)
Enter user name(admin) and password(admin)
Browser window should now display the camera video window and a
left hand control panel
Configure
Camera with
network & user
settings
Click ―System Setup‖ and configure required network settings for
wireless access, remote access from the internet and mobile phones
and setting email alerts
Configuring
Wireless
Network
Access
Go to Menu: System Setup—Network—Wifi
Click ―Scanning‖
Select the wireless network you wish to use
Enter encryption and password settings(refer to your wireless
broadband router user guide)
Click ―Apply‖ the camera will reset and the Ethernet cable must be
disconnected.
When the camera restarts, you should be able to see the camera

7
video in the browser window. If not, then recheck your wireless
network settings.
Viewing the
Camera
remotely with
UPnP
Go to Menu: System Setup—Network—UPnP
If your router supports UPnP then Enable UPnP Port forwarding
which allows camera to open ports on the router automatically so that
the video streams can be sent out from your internal network.
Get the IP and port settings from ―system setup –system status
–UPnP—Internet address
To access the camera remotely type http://ipaddress:httpPort/ in
your browser window.
Viewing the
Camera
remotely using
DDNS
Go to Menu: System Setup—Status
Note the local IP Address, http port and control Port and External IP
Address, http port and control Port.
If your router doesn’t support UPnP, you will get an IP address for the
camera that can be accessed from the internet.
You must register with a free dynamic DNS service such as DynDNS
(http://www.dyndns.com). They will assign an external hostname
that is linked to your external Hostname that is linked to your internal
IP address which you can use to access your camera from the
internet.
You must first ―port forward‖ the camera Local web port and Local
sever port for the camera Local IP address in your router
configuration(refer to your router documentation).
To access the camera remotely type.
http://hostname.dyndns.org:http web port in your browser
window.
Viewing the
camera
remotely on a
mobile phone
via RTSP over
a mobile phone
network or
via a wifi
connection
Go to Menu: System Setup—Status
Note the internet IP address, rstp Port and extension name. To
access the camera remotely from your phone type
rtsp://ipaddress:rstpport//main.mp4 in your browser window Or…
Go to Menu: System Setup—Stream Settings—Stream list
Note the Internet IP Address, rstp port and extension time. To access
the camera remotely from your phone type
rtsp://ipaddress:rtspport/mobile in your browser window
A streaming application such as RealPlayer will load and play the
video stream on your phone.
Note: some mobile operators block rtsp video streaming. In the case
you may only be able to view the camera video stream on your mobile
phone using a WIFI connection.
802.11b/g Wireless LAN Connection Available
The camera is designed to not only work with your existing wired network but also with
standard 802.11b/g wireless devices, allowing the flexibility to operate the camera wirelessly.
The camera utilizes SSID filtering. Powerful 64/128 bit WEP and new security standard WPA
encryption to protect you from illegal instruction.

8
3GPP Mobile Surveillance
The camera provide the ability to view the cameras monitored through your mobile phone as
a live video stream, it supports the telecommunications standard of 3GPP streaming format.
All 3G Enable mobile devices and most 2G phones that support the streaming standard of
3GPP are compatible.
Simultaneous High-speed MPEG-4 and Motion JPEG
The camera allows live the MPEG-4 and Motion JPEG streams simultaneously. The camera
features MPEG-4 compression which compresses the video to make transmission faster
and more efficient. The MPEG-4 and MJPEG image can be transmitted at 30frames per
second.
Simultaneous HTTP and RTSP streaming
The camera support HTTP and RTSP/RTP/RTCP protocol, and provide multiple HTTP and
RTSP streams simultaneously
Audio Transmission
The camera comes with a built-in microphone for audio monitoring as well as video
monitoring .Sound captured by the camera is transmitted to the client’s PC
Snapshot and Recording
You can capture a still image of the camera view on your PC and save the image as JPG or
BMP format file. You also can record the video and audio captured by the camera on your
PC and save as anASF format file.
Motion Detection Function
The camera can detect changes in the image being monitored .Once a change occurs it will
send an email to up to 3email address with a video file or snapshot attached .The video file
or snapshot can also be uploaded to an FTP server .In addition the camera can be
configured to send images at regular intervals.
OSD Function
OSD (On Screen Display) function can display system name, date and time and
user-defined on screen
Authentication
An authentication window requires you to enter the user ID and password .Password
security can prevent unregistered users from accessing your camera .Users can select
Basic Authentication Method or Digest Access Authentication method.
Multi-Client Access
The camera allows up to 6users to view simultaneously .Please note that this is possible
that as the number of simultaneously connected users to camera increases ,the overall
motion performance will decrease.

9
Infrared Night Vision
The camera utilizes 30infrared LED to provide high in dark environment. When the environment
is dark, the LED will be opened automatically due to a photosensitive component, and the
moving images will be changed to Black and White. User can monitor clearly the things within
15meters distance. Users also can select open or close the infrared LED manually, and select
whether change the image to black and white or color automatically.
Adapter
The product conforms with the authenticated AC adapter .The adapter is marked with one
or more of the following.
Notice:
When using the power adapter, make sure the rating voltage on it is compatible with that of the
device to avoid potential damages resulting from incorrect usage of power supply .
PC System Requirements
The PC(personal Computer )and the network must meet the following technical
specifications for camera to work properly
1. Processor: Intel Pentium III, 1GHZ or Higher (Pentium IV, 2GHZ or Higher recommended)
2. RAM: 256MB or more
3. Color Monitor: Suggest at least 800x600 and the latest driver for the Display Adapter
4. OS (Operating System):Windows2000/XP/Vista
5. Web Browser: Internet Explorer version 5.0 or above, DirectX 9.0C or later
6. Network Protocol: TCP/IP network protocol installed
7. Interface: 10/100 Mbps Ethernet card/wireless Network card for your network connection
8. Other: CD-ROM Drive

10
Installation
Connecting the cameras
Using a standard Ethernet network cable, connect the camera to your network (depending on
your own setup, this may be to your router or switch). See figure below
Connecting the adaptor with power, camera will detect automatically, and the ―power‖ status LED
will blinks. Then, Network camera will be ready to start.
Rear view of camera
Notice: Please be careful when connect the adapter to socket
Camera Search tool Installation & Usage
Camera Search tool can connect quickly to your cameras in LAN and set out them
in the window. Meanwhile, you can set up the IP address to every camera in this
software.
1. Insert the Installation CD into your CD-ROM drive and the installation screen should appear
automatically (See image below). If not, click ―autorun.exe‖ in the text.
DC5 Adapter
RJ45 network cable

11
2. Click on ―Install Software‖ and the following screen will be displayed. And click ―Next‖ and
install:

12
3. If you want to change the default files, click ―browse‖, otherwise click ―next‖.
4. Click ―install‖
5. Click Finish to end the installation

13
6. You should now find an icon on the desktop.
7. Double-click the ―Camera Search‖ icon on the Desktop to launch the program. The Camera
Setup utility should automatically find your camera if is correctly connected

14
【Search】: Click Search to search the cameras in LAN
【Setup】: Select the required camera and click Set up the network configuration
【Open】: Select the required camera and click Open to access the camera via a
web browser
【Exit】:Click Exit to exit the Camera Setup window
Notice: Select and double click to open the camera view via the web browser.
Run the “Camera Search” program to locate the newly installed network cameras
Notice: If there is no DHCP server, Network Cameras display the factory default IP
address in the search software, factory default IP address: 192.168.1.239. When there are
DHCP server in the LAN, MINI Series Network Camera will obtain IP address automatically
from the DHCP server and display in the device list with the LAN IP address. Please make
sure that IP address of net work camera is different from other devices’.
1. Run the ―Camera Search‖, program will search cameras in LAN automatically
2. Select one of the IP from the device list (the selected one show with blue), click on the
"set up" button, the following screen will be displayed.
3. 【Name】：Enter a unique name for the camera【Description】: Input description, such as
location of camera 【Http Port】: Default is 80.
―Obtain IP address automatically‖ and ―obtain DNS server address automatically‖ are default,
and also you can choose ―Use the following IP address‖ to set up by yourself. Please follow the
step 4 to 7. If you need to save default setting, you can see next page directly.
4. To obtain the IP addresses specific to your network, click ―Start‖—“Run”, then type “cmd”. A

15
window of MS-DOS will be displayed, and then type “ipconfig/all”—press Enter, a screen
similar to the one below will be displayed.
5. Take note of the following:
IP Address
Subnet Mask
Default Gateway
DNS Servers
6. Enter the details noted in step 5, and input relevant fields. IP address should be different.
7. Input user and password, and click ―ok‖, the following screen will be displayed.
Click―OK‖ and finish.

16
NETWORK CAMERA SCREEN AND SETUP
WINDOW
Review Images from the Network CAMERA
You can select one of the three ways to review pictures from the camera.
1. Input the assigned IP address (or URL) of the camera on the Web Browser., for example,
192.168.1.239. The below dialog will appear. Input the correct username (the default is admin, in
lowercase) and password (the default is admin, in lowercase). Choose the language (the default
is English),you are allowed to enter the picture viewing interface or the system setting interface.
The general users assigned by the administrator are not allowed to enter the system setting
interface. They
can only be permitted to enter the picture viewing interface.
2. Open ―camera search‖ Tool and double-click the relevant camera item.

17
3. Run manage device in video client software.

18
Introduction of Main page
When access the network camera at the first time, IE will be prompted to install the ActiveX
control. Users can install it with the following steps:
Click the highlight in blue, the following page will appear.
When you download and install the ActiveX control, refresh the page.
You will then view the following screen in your web browser.

19
1. Multi Devices select
a) First add device in system setting, ―camera setting‖—―multi
channel setting‖
b) Select four channel or nine channel
c) Choose one camera, and then capture, record and image setup.
2. Screen Size
a) :Full screen
b) ：640*480
c) ：320*240
d) ：160*120
3. Basic Setting
a) ：mirror
b) : flip
c) ：frequency

20
4. Image Setting
You can adjust the Brightness, Contrast, Saturation and hues of
the image, you also can restore to Default Image by Deflaut
button.
5. Press the Record button.
a) ：snapshot
b) ：Click Record, the color of the button will change to
6. The default is mute, and click “Audio” button to open the audio. Click on button and
button to adjust the volume
System Setting
From the home page click ―System Setup‖ to start the ―advanced function‖ setting. First you can
see page of status.