Celsi B-1033765 User manual

Electristove Hologram Genesis Electric Stove
Electristove Hologram Genesis - B-1033765 - ESEHG0RE
Packing Checklist - Pack 1 of 1
Electric Stove
Remote Control Handset* with wall mounting bracket
Log Set
Instruction Manual
*THIS PRODUCT REQUIRES 3 X AAA BATTERIES FOR USE I THE HA DSET ( OT SUPPLIED)
IMPORTA T
PLEASE READ THESE I STRUCTIO S CAREFULLY BEFORE
I STALLATIO A D USE OF THIS ELECTRIC STOVE A D
RETAI FOR FUTURE REFERE CE.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the stove
provided that it has been placed or installed in its intended normal operating position and
they have been given supervision or instruction concerning use of the stove in a safe
way and understand the hazards involved. Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the stove or perform user
maintenance.
This stove is not intended for use by persons (including children) with reduced
physical, sensory or learning disabilities, or lack of experience and knowledge, unless
given supervision or instruction concerning use of.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.

IMPORTA T SAFETY ADVICE
WHE USI G A ELECTRICAL STOVE, BASIC PRECAUTIO S SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK A D
I JURY TO PERSO S, I CLUDI G THE FOLLOWI G IMPORTA T SAFETY ADVICE.
DO OT cover the heater, to avoid overheating of the product.
DO OT leave the heater unattended while it is in use. Always turn the stove to the OFF
position and switch off at the mains socket when not in use.
DO OT leave children unsupervised whilst the stove is switched on.
DO OT operate this stove with a damaged cord or plug, or after the stove
malfunctions, has been dropped or damaged in any way. Contact the manufacturer.
DO OT install a timer switch to operate the stove.
DO OT insert or allow objects to enter any ventilation or exhaust openings on the
stove. To prevent a possible fire do not block air intakes or exhaust openings in any manner.
DO OT place this stove near flammable materials, surfaces or substances, as there may be
a risk of fire. eep flammable materials, surfaces or substances at least 1 metre away from
the front of the product.
DO OT switch on the stove if volatile vapours are present in the room.
DO OT use this stove in any areas where petrol, paint or other flammable liquids are
stored e.g. a garage or a workshop as the stove contains components capable of
producing a spark.
DO OT touch any hot surfaces such as the heater vent when the heater is in use to avoid
burns and personal injury.
DO OT install the heater immediately below an electrical socket outlet.
DO OT use outdoors.
CAUTIO - Some parts of this product can become hot during use and cause burns.
Particular attention has to be given where children and vulnerable people are present.
This stove is for household use only
Page 1 of 18

PRODUCT TECH ICAL DATA SHEET
Supplier ame / Trademark Celsi
Supplier Model Identifier B-1033765
Electristove Hologram Genesis
Voltage 230v AC 50HZ
Fuse 13 Amp
ominal Heat Output (Measured) 2.0kW
Minimum Heat Output (Indicative) 1.0kW
Maximum Continuous Heat Output 2.0kW
Auxilliary Electrical Consumption 33W
at ominal Heat Output
Auxilliary Electrical Consumption 33W
at Minimum Heat Output
Auxilliary Electrical Consumption 1.5W
at Standby Mode
Type of Heat Output / RTC* With electronic room temperature control
plus 7 day timer.
Other Control Options With adaptive start control
Manufacturers ame and Address BFM Europe Ltd. Gordon Banks Drive,
Trentham Lakes, Stoke-on-Trent,
Staffordshire, ST4 4TJ
*RTC = Room Temperature Control Tel: [phone]
Stove Dimensions - Fig. 1
Page 2 of 18

Unpacking
Remove and discard the plastic bag.
Be responsible when handling the packing materials.
eep the original packaging for future transportation and/or storage.
Check all accessories are removed from the packaging before storing it away for future use.
KEEP PLASTIC BAGS AWAY FROM CHILDRE !
Choosing a Suitable Location
The stove must have a minimum clearance of 15mm to combustible material on all sides.
A clearance of minimum 15mm to non-combustible materials is also required to ensure
correct operation.
This stove is for indoor installation only and is not designed to be installed outside. The stove
must be kept away from any source of damp or moist conditions. Avoid any close contact
with water. Stove must be installed on a non-combustible hearth.
If there is any doubt regarding the suitability of the installation site please contact your
retailer.
The stove can be connected directly to a fused spur or plugged into a mains socket.
Ensure that the plug socket-outlet connection for this stove is accessible. It MUST be readily
accessible for easy electrical isolation in the event of servicing and replacing
components etc.
This stove MUST OT be located immediately below an electrical socket-outlet.
Installation
Installation must be carried out by a qualified and competent person.
Connect the stove to single-phase AC supply of the voltage specified on the rating plate.
Should the stove be connected directly into the mains supply, then a fused switched spur
with a 13 amp fuse must be fitted.
It is imperative that the power supply is capable of handling the electrial load as stated on
page 2 of this manual.
This stove must be earthed.
Do not use an extension lead.
Always ensure that all electrical work complies with the relevant Building
Regulations and the Electrical Code of Practice. All electrical work should be
carried out by a qualified electrician.
E SURE THAT THE HEATER ELEME T OUTLET IS OT OBSTRUCTED A D
COMBUSTIBLE MATERIAL IS OT PLACED I FRO T OF IT.
Page 3 of 18

Fitting the Logs
Take care when unpacking the Logs supplied with your stove.
Open the door on the stove then remove the top panel via the two screws at the front and
the screws at the rear as indicated below in figure 2 & 3.
Fig. 2
Fig. 3
Figure 4 overpage image shows the stove top panel therefore removed to allow access.
to the Top front LED strip retaining screws .
Remove the screws as indicated to allow the fuel-bed log set to be fitted.
Page 4 of 18
Fixing screw
(L/H/S) x 1 off
Fixing screw
(R/H/S) x 1 off
Fixing screw
(L/H/S) x 1 off
Fixing screw
(R/H/S) x 1 off

Fig. 4
Remove the screws as indicated to allow the fuel-bed log set to be fitted, carefully relocate
the LED strip temporarily towards the rear of the stove to allow access to fit the fuel-bed
matrix and 2 off loose logs as shown below in figure 5 & 6, this will provide the layout from
the front view as displayed in figure 7 below.
Fig. 5 Fig. 6
Fig. 7
Refit the LED strip and Stove top panel. Page 5 of 18
Front LED strip
retaining screws
Fuel-bed matrix to be positioned
centrally as shown
Loose logs to be positioned
at L/H/S & R/H/S of matrix as shown

Operating the Stove
This stove can be operated using 4 methods:
Manual Control using the controls on the stove
Remote Control using the included remote-control handset
Celsi App Control voice control using Alexa or Google Assistant
Manual Control
This stove can be operated manually using the control panel as shown below in figure 8.
Fig. 8
O / OFF Power Switch
This switch is used to turn the mains supply to the stove
ON or OFF. When the switch is in the ON position an indicator
light located in the centre of the screen will glow amber to
indicate the stove is switched on and in standby mode.
This needs to be in the ON position for both manual and
remote operation.
STA DBY
Used to switch stove ON or OFF into standby mode.
FLAME
Pressing this button will cycle through the 4 different flame
brightness levels.
HEATER
Use this button to select Low Heat, High Heat or heater OFF.
When LOW heat is selected the indicator light will glow amber for 5
seconds. When HIGH heat is selected the indicator light will glow
red for 5 seconds.
Please note the heater will only operate when the room temperature
is below the temperature set on the handset, which can be adjusted
using the remote control or app. When the heater switches off, the
fan will still continue to run for a short period to allow the stove
to cool down.
MODE
Use this button to cycle through and select 1 of the 16 preset LED
colour combinations. Press and hold until a confirmation beep is
heard to set on ‘Colour Animation’ mode to slowly cycle through all
the colour combinations.
Page 6 of 18

Remote Control
Remove the battery cover on the rear and insert 3 x AAA batteries ensuring the batteries are
fitted correctly. Refit the cover. Please ensure old batteries are disposed of responsibly by
contacting your local authority about recycling schemes.
Ensure that the ON / OFF Power Switch on the stove is in the ON position.
Before the handset as shown below in figure 9 can be used the current day and time will
need to be set (see clock setting instructions on the next page).
Fig. 9
Page 7 of 18

To use the remote handset ensure it is pointed directly towards the stove and press the
appropriate button to operate the stove.
Operating the Stove and Child Lock mode
1. Use the On/Off button to switch the stove On and Off.
2. Holding the button in for 5 seconds will enable the Child Lock mode
(a padlock will appear on the handset display).
3. To disable the child lock press the On/Off button once.
Note: that after a short period of time the handset will automatically
enable the Child Lock mode.
Clock Setting
1. Press the Clock Set button, which will start the day cursor to blink.
Using the selection wheel rotate to the current day e.g. S M T W T F
S then press the Clock Set button to confirm.
2. The hour will now be blinking, set using the selection wheel and
confirm using the Clock Set button.
3. The minute will now be blinking, set using the selection wheel and
confirm using the Clock Set button.
Flame Setting
1. Pressing this button will cycle through the 4 brightness settings of
the LED flame effects.
Heat Setting
1. Use to change the heater setting from LOW, HIGH and OFF
2. When the heater is ON the actual room temperature is displayed on
the handset
3. By using the selection wheel you can set the desired temperature,
this will save after 5 seconds and the room temperature will be
displayed
Note: the heater will only operate when the room temperature is below the
temperature set on the handset. When the heater switches off, the fan will
still continue to run for a short period to allow the stove to cool down.
The displayed temperature can be displayed in Celsius or Fahrenheit.
To change use the Temperature units button.
Page 8 of 18

LED Colour Settings
1. Press the Mode/Set button and use the selection wheel to select one
of the 16 preset LED colour combinations (the preset number will be
displayed on the handset)
If preferred, the LED colour settings can be changed individually for the
Flame Logs Ember
1. Press the one of the buttons above (symbol will flash on display)
and use the selection wheel to select your required colour setting for
the specific lighting function.
Alternatively the stove can be set to Colour Animation mode
1. Pressing the Colour Animation mode button will set the Lighting to a
red glow and then will slowly cycle through the 16 preset colour
combinations.
2. Press the Colour Animation mode to exit the animation mode.
Adaptive Mode
Adaptive mode works in conjunction with the timer programmes. When
Adaptive model is turned ON the stove monitors the room temperature in
relation to the selected target temperature. If the room temperature is
sufficiently lower that the selected temperature the Adaptive mode will
instruct the stove to switch on up to 10 minutes earlier than the set time to
ensure the room is at the required temperature at the set time.
Celsi App Control
The Celsi app can be downloaded from the IOS App Store or the Google
Play Store by either searching for Celsi or by scanning the QR code using a
smart phone or tablet.
Page 9 of 18

The Celsi app can be used alongside the remote handset and provides additional feature of 7
day Timer function.
** During the initial set up of the App, the fire needs to be in pairing mode **
Pairing Mode
With the stove off and in Standby mode press and hold the Standby button on the fire to
hear a beep and continue holding for 5 seconds to observe a red flashing light on the rear
screen. When this light is flashing the product is in pairing mode.
App Setup
1. Open the app and when prompted either create a new Celsi account or
Login using your existing account details.
2. Once logged in, accept the notification to allow permission for the Celsi app
to access Notifications and Bluetooth.
3. On your smart device ensure that Bluetooth and Wi-Fi are switched ON.
4. Ensure the stove is in pairing mode.
5. On the app the All Devices screen will be displayed. Press the + button at
the top R/H corner.
6. Allow the app to connect to devices on local network.
7. Click on Add button to discover devices.
8. Click on Manual Input and add the name and password of the Wi-Fi net
work you are connecting the fire to.
9. Follow the on screen instructions to add device.
Using the App
Fig. 10
The Home page of the app will allow you to
operate and customise the appearance of your
stove using the touchscreen interface as shown
opposite in figure 10.
The app has all the same features as the
remote handset along with an additional 7 day
Timer function. Using this function you can set
timers for the stove to switch on at a given time
day / time.
Further information is available within FAQ
section of the app.
Page 10 of 18

Connection to Alexa
Once you have set up your Celsi account and successfully paired your device you can now
also connect to Alexa.
Fig. 11 Fig. 12
To connect, open the Alexa App and select the “More” tab in the bottom right hand corner as
shown in figure 11 above.
Then select the “skills and games” tab as indicated in figure 12 above.
Page 11 of 18

Then click the “search” icon in the top right hand corner as shown below in figure 13, then
search for the “smart life” skill by typing “smart life” into the search box as shown below in
figure 14.
Fig. 13 Fig. 14
Install onto your device by clicking the ”smart life” icon shown below in figure 15, then the
“enable to use” icon as shown in figure 16.
Fig. 15 Fig. 16
Page 12 of 18

This will prompt you for your e-mail address and password that you used when registering
the Celsi APP as shown below, enter the e-mail address and tick the user agreement box as
indicated below in figure 17.
Complete the verification puzzle as prompted, then enter your password and complete a
second verification puzzle as requested.
This will then bring up the confirmation page that the account has been successfully linked
as shown below in figure 18.
Fig. 17 Fig. 18
The product should then operate from voice activation.
i.e. “Alexa, turn fire on”, “Alexa, turn fire off”.
Page 13 of 18

Connection to Google Assistant
Once you have set up your Celsi account and successfully paired your device you can now
also connect to Google Assistant.
Fig. 19 Fig. 20
To connect, open the Google Assistant App and select the “Device” tab on the left hand side
as shown above in figure 19, then click the “add devices” tab when prompted as shown
above on the right in figure 20.
Then select the “link a smart home device” tab as indicated overpage in figure 21
Page 14 of 18

Select the “link a smart home device” tab as indicated below in figure 21
Fig. 21 Fig. 22
Click the “search” icon in the top right hand corner as shown figure 22 above, then enter
“smart life” as the searched for as shown in figure 23. Select the “smart life icon as shown
in figure 24 below.
Fig. 23 Fig. 24
Page 15 of 18

This will prompt you for your e-mail address and password that you used when registering
the Celsi APP as shown below, enter the e-mail address and tick the user agreement box as
indicated below in figure 25.
Fig. 25
The product should then operate from voice activation, open the google assistant app, click
then click the microphone logo at the bottom centre and give instruction i.e. “turn fire on”,
“turn fire off” as shown in figure 26 below.
Fig. 26
Page 16 of 18

IMPORTA T
This stove is fitted with an automatic thermal cut-out safety feature to reduce the risk of
damage to stove due to overheating. If the stove overheats the heater element will cut out
whilst the fan will still continue to run to allow the fire to cool down sufficiently.
Once the stove has cooled down the thermal cut-out will reset itself and switch the heater
back on. If the problem persists switch the stove off and disconnect the power at the switch
and plug socket. Check that the heater warm air outlets and the inlets are not obstructed
(the outlets and inlets are situated on the underside of the stove body).
If the heater is still not operating correctly disconnect the stove and seek expert advice.
Maintenance Instructions
Always remove the plug from the socket-outlet and allow the heater to cool down before
cleaning. User maintenance should only be carried out by a competent person.
Light accumulated dust may be removed from the stove with a soft dry cloth.
The exterior surface of the stove can be cleaned with a soft damp cloth (not dripping wet).
Dry the exterior surface before operating the heater.
Household glass cleaner can be used on the stove glass.
WAR I G!
Do not immerse the heater in water.
Do not use any cleaning chemicals such as detergents and abrasives.
Do not allow the interior to get wet as this could create a hazard.
In the event of malfunction contact the manufacturer, do not try to repair the heater yourself
as this may result in a fire hazard or electric shock.
Environment
Fig. 27
Do not dispose of electrical appliances as unsorted municipal waste.
Use separate collection facilities. Contact your local government for
information regarding the collection services available in your local
area. If electrical appliances are disposed of in landfills or dumps
hazardous substances can leak into the groundwater and get into
the food chain, thus damaging your health and wellbeing.
When replacing old appliances with new ones the retailer is legally
obligated to take away your old stove for disposal free of
charge.
Page 17 of 18

Warranty
Congratulations on the purchase of your electric stove. This stove by BFM Europe Ltd is
guaranteed for 5 years from the date of purchase against faulty materials or workmanship.
Please note the 5 year guarantee comprises of 24 months of parts and labour with an
extended 36 months of parts only. If your stove is found to be defective within 24 months
from the date of purchase, we or our authorized agent will repair the faulty
component on site.
This warranty does not cover consumable items which have a limited lifespan.
If a problem should occur, the nature of the problem together with the date of purchase and
installer information should be immediately reported to the retailer that the stove was
purchased from. Proof of purchase will be required so the original invoice should be retained.
B-1035343
Issue 2
BFM Europe Ltd
Gordon Banks Drive
Trentham Lakes
Stoke-on-Trent
ST4 4TJ
Technical Queries: 01782 339039
Service Fault Enquiries: 01782 339008
Spare Parts - www.bfm-partfinder.co.uk
Page 18 of 18