GENERAL OPERATION
1) Always make sure your drivers are properly secured to the
gearbox under the machine.
2) Make sure when using the center-lock with a cleaning pad,
that the center-lock is recessed below the pads surface. This
must be checked during operaon. Failing to do so, may
result in damage to the center-lock and or oor surface.
3) When a pad becomes soiled, remove pad and turn over to
expose the clean side. Remove and wash pad aer both sides
become soiled.
4) Do not operate the machine in the same spot for a long
period of me. Floor damage may result.
5) To maneuver over thresholds and oor grates, stop the
machine and lt it back on the transport wheels.
6) When the machine is not in use, do not leave machine
standing on the brush/pad. Brush/pad damage may result.
ATTENTION: Should you feel the machine come out of your
control, beyond your abilies. You can release your hands
from the handle grips and step away from the machine quickly.
If maintained, your machine will come to a stop. Doing so, may
result in damage to walls / items, and impact body.
MACHINE MAINTENANCE
WARNING: Electrical hazard. Unplug power cord before ser-
vicing machine.
1. Remove and clean the pad driver/brush aer each use.
2. Clean the machine base aer each use, clean boom edges
of SplashGuard to remove debris or loose diamonds.
3. Inspect power cord for damage aer each use. If worn or
damaged, replace immediately.
4. Wipe the power cord with damp cloth and neatly coil it
around the cord hook and handle aer each use. Use
supplied Velcro wrap strap to secure cord.
5. Periodically check that all nuts, bolts, screws are ght.
6. When red light appears on top of motor cover, this indicates
your motor brushes need to be replaced. Only use an
authorized Service Center—contact Centaur Floor Machines
for further informaon. 905-475-5640
TECHNIQUE
This is intended as a guide to assist you in your operaon of this
machine. This picture illustrates the “Cross Hatch” technique,
where you work in a 10FT by 10FT secon, starng in the top le
corner. With water applied, start operang the machine sideways,
slowly, working in a le to right paern unl you reach the end of
the 10 secon. From there you will take a “half step” backwards
(overlapping) and repeat the le to right process and repeat unl
you have worked backwards 10. At that point you turn your body
90-degrees and begin again in the upper le corner and repeat the
same process. Working in a cross-hatch you will grind, hone and
polish very evenly and will eliminate any “ger striping” that may
occur otherwise.
MACHINE OPERATIONAL INFORMATION
FOR SAFETY: Do not operate machine, unless operator manual
is read and understood.
Read and thoroughly understand the warning and cauon
applied to the operaon of this machine.
Refer to Page #4 to for the assembly, and how to use this
machine.
OPERATING THE OPTIONAL WATER TANK
1. Make sure drain plug is secure. Turn knob clockwise to
ghten.
2. Fill the water tank with water only. Any chemicals may
result in damaging the internal valve system.
3. Ensure the outside shut-o valve is pointed in the “UP”
posion to allow water to ow.
4. Pull the water tank handle upwards toward the handle to
actuate ow of water.
5. To drain, release the tri-nut and lower handle, place bucket
below drain plug. Turn the drain plug knob counter
clockwise to loosen and remove from tank.
6. Aer draining water, insert drain plug and ghten.
WARNING: Do not store machine equipped with water tank
outside or in temperatures below +5C, freezing of water can
damage components of valve and tank.
CLEANING CARPETS
Shampoo carpet brush or bonnet driver with bonnets are
required. Do not use a brush that is intended for hard oors;
personal injury and carpet damage may result. Consult Centaur
Floor Machines (info@centaurmachines.com) or a local
distributor for recommendaons.
Before operang the machine on carpet, the carpet must be
pre-sprayed with an approved cleaning soluon. The soluon will
act as a lubricant to allow the shampoo brush or bonnets to spin
with lile resistance.
When using the dual speed model to clean carpets, do not
operate machine at high-speed; personal injury or carpet
damage may result.
For best cleaning results allow the pre-sprayed cleaning soluon
to “dwell” on the carpet for approximately 10-12 minutes before
scrubbing. Using only shampoo carpet brush or bonnets with a
bonnet driver, operate the machine at a gradual, steady pace.
Aer scrubbing, while carpet is sll wet, use an extractor or
wet/dry vacuum to pick up suspended soil and foam.
Then vacuum carpets when it is completely dry.
TRANSPORTING THIS MACHINE
1. Unplug the power cord and remove the pad from the
machine. Neatly coil the cord around the cord hook and
handle to prevent cord damage. Secure cord with supplied
Velcro wrap strap
2. Load the machine using a recommended loading ramp or
carefully li the machine with adequate assistance.
3. Secure machine with e-down straps when transporng by
vehicle.
