Challenger SmartForce ASFFOB User manual

Challenger_ASFFOB_Instructions_Rev01
ASFFOB
Wirefree Remote Control
Installation and Operating Instructions
These instructions should be read in conjunction with your System
Installation and Operating Manual and be retained for future reference
A LED indicator E Panic Switch
B Arm F Key Chain Ring
C PartialArm G Negative Polarity
D Disarm H Positive Polarity
The Remote Control is used to Arm, Part-Arm and Disarm the system. It is
compatible with a control panels operating at 868MHz.
The Remote Control also incorporates a Panic switch. Activating the Panic switch
will immediately initiate a Full Alarm condition whether the system is Armed or
Disarmed, (unless the system is in Test mode).
The Remote Control requires a CR2032 type Lithium cell which under normal
conditions will have typical life expectancy of 1 year. Under normal battery
conditions the LED on the Remote control will only illuminate when a button is
pressed. However, under low battery conditions the Orange LED will illuminate
every time the button is pressed. When this occurs the batteries should be
replaced as soon as possible.
SETTING THE REMOTE CONTROL
1. Remove the rear cover with a coin.
2. Insert the battery ensuring that the +v
terminal faces upwards away from the PCB.
3. Replace the rear cover.
IMPORTANT NOTE: The remote fob supplied in the kit HAS already been
learnt to the Gateway Hub and does not require learning to the ASFK1 Gateway
Hub. For replacement or additional remote fobs these will need to be learnt to the
Gateway Hub before use.
LEARNING ASFFOB
Please refer to Smart Force Quick Set Up Guide. The easiest way to learn the
device is either via through the Smart Force Web Site or Smart Force App once you
have completed the System Registration.
Pressing the Disarm button will emit the ID code to the Gateway Hub instantly,
subject to the Gateway Hub being set to learning mode.
Note: If no ID code is stored in the remote fob after power-on, the remote control
will automatically enter Learning mode. The learning process lasts for 30 seconds.
Press any button will initiate learning mode again until the code learning is done.
To link the remote fob to the gateway Hub, proceed with the following steps in
sequence:
1. Put the Gateway Hub in to learn mode via the Smart Force Web User Interface
or Smart Force App. Then select add a device.
2. Press and hold the Disarm button for more than 3 seconds until the green LED
of the Remote Control flashes. It implies that the Remote Control enters ID code
learning mode.
3. A 30-second countdown will start. If the ID code has been learned within 30
seconds by the Gateway Hub successfully, the LED of the Remote Control will
be on shortly. If failure, the LED of the Remote Control will flash three times
rapidly.
LED INDICATION
Function
LED Indication
RF transmission Green LED illuminating for one second
Failed RF transmission Red LED illuminating for one second
Low battery Orange LED illuminating for one second
Code learning LED flashing at 2-second interval
Success in learning the ID code Green LED illuminating for 0.5 second

Challenger_ASFFOB_Instructions_Rev01
OPERATING THE REMOTE CONTROL
1. Pressing the Arm button will control the control panel to enter the arm mode.
2. Pressing the Disarm button will control the control panel to enter the disarm
mode.
3. Pressing the Partial Arm button will control the control panel to enter the
part-arm 1.
4. By sliding the panic switch will activate the control panel to initiate a full alarm
condition.
TESTING THE REMOTE CONTROL
The operation of the Remote Control should be tested with the system in normal
mode to ensure that the new Remote Control will successfully communicate with
the system and the Arm and Disarm functions operate correctly. Also check by
activating the Panic switch on the Remote to initiate an alarm condition.
Refer to your System Installation and Operating Manual for further details on
operating and testing the system.
SPECIFICATIONS
Battery Type
CR2032 3V/230mAhr
Operating Frequency
868MHz
Due to our policy of continuous improvement we reserve the right to change
specification without prior notice.
Errors and omissions excepted. These instructions have been carefully checked
prior to publication. However, no responsibility can be accepted by Challenger for
any misinterpretation of these instructions.
Challenger Security Products
10 Sandersons Way, Blackpool, FY4 4NB
Tel: [phone], Fax: [phone]
Email: [e-mail]
Web: www.challenger.co.uk