Eldes KeyBoB User manual

User manual v1.0
CONTENTS OF PACK
Item Quantity
1. KeyBoB ..................................................1
2. CR2450 3V lithium battery ................1
3. Key ring ..................................................1
3. Warranty leaet ...................................1
Main features:
• Alarm system arming &
disarming;
• PGM output control;
• Partition switch;
• Stay Arm;
• Up to 8 actions with a
single key fob
• Key fob assignment to
User
• Inaudible Panic alarm
• Visual and audio in-
dication of command
status.
1. GENERAL INFORMATION
Key fob, named KeyBoB, is a wireless device intended to re-
motely arm and disarm ELDES alarm system, cause inaudible
Panic alarm or control any electric appliance connected to the
alarm system’s PGM output. The maximum wireless connection
range is 1700m (5577ft) in open areas.
By default, none of key fob’s buttons are pre-congured. Thus,
user can congure each key fob depending on the personal
preferences. A single key fob allows to complete up to 8 pos-
sible actions (i.e. 2 actions can be assigned to each button). EL-
DES alarm system supports up to 10 KeyBoB devices with the
custom conguration.
2. TECHNICAL SPECIFICATIONS
1
Congurable
functionality
Congurable
functionality
Disarm the
system
(congurable
functionality)
Arm the
system
(congurable
functionality)
LED
indicator
The hole to attaching
a key ring
NOTE: Pic. No. 1 reects the default key fob’s button
conguration. All key fob buttons are congurable ac-
cording to individual needs via Eldes Utility software.
2.1. Electrical & Mechanical Characteristics
Battery type*........................... 3V Lithium CR2450 type
5029LC (ANSI/NEDA)
Quantity of batteries.............. 1
Battery operation time** ...... 10+ years, or time period
equivalent to 15,000 button
presses
Wireless band .......................... ISM868
Range of operating................. -10…+55 °C (14... +131°F)
temperatures
Humidity................................... 0-90% RH @ 0... +40°C
(0-90% RH @ +32... +104°F)
(non-condensing)
Dimensions .............................. 69x35x12.6mm
(2.72x1.38x0.496in)
Wireless connectivy range.... Up to 1700m (5577ft) in open
areas
Compatible with***................ ESIM384; Pitbull Alarm PRO
*CR2450 3V lithium battery used as standard. Also CR2320
3V lithium battery can be used with specially adapted bat-
tery holder. The standrard battery is included in the device.
** This operation time can be achieved by pressing the key
fob’s buttons up to 4 times per day. The operation time de-
pends on dierent conditions and may vary.
*** Devices are compatible only with the latest rm-
ware versions.
3. HOW TO USE:
In order to start using KeyBoB, you must pair it with ELDES
alarm system using ELDES Utility software (see chapter 4.
PAIRING KEY FOB WITH ALARM SYSTEM).
KeyBoB features 4 congurable buttons, intended to operate
according to individual needs. User may choose up to 8 actions
for a single key fob: 4 short press actions (i.e. to assign 1 “click
and release” type of action to each button) and 4 long press ac-
tions (i.e. to assign 1 “click and hold” type of action to each but-
ton). User can set any action to any button (the only exception
is Panic alarm action - dedicated for long press ONLY).
Below you’ll nd the list of all possible actions and the descrip-
tion of each action:
• Arm System (Instant) – After the button is pressed,
this function instantly arms the system. KeyBoB’s internal
buzzer will emit 5 short beep sounds, LED indicator (red)
will light up, conrming a transferred command to ELDES
alarm system via wireless connection. Otherwise, key fob’s
internal buzzer will emit 1 long beep sound and LED indica-
tor (red) will light up or ash quickly, informing user about
unsuccessful attempt to transfer command (due to the
system’s violation (action failed) or the wireless connec-
tion loss (out of range)).
• Arm (Exit Delay) – After the button is pressed, this func-
tion arms the system after exit delay countdown is over
(by default, exit 15 seconds). KeyBoB’s internal buzzer will
emit 5 short beep sounds, LED indicator (red and green)
will ash alternately, conrming a transferred command to
ELDES alarm system via wireless connection. Otherwise,
key fob’s internal buzzer will emit 1 long beep sound and
LED indicator (red) will light up or ash quickly, informing
user about unsuccessful attempt to transfer command
(due to the system’s violation (action failed) or the wire-
less connection loss (out of range)).
• Arm (Stay mode) – After the button is pressed, this
function arms the system in Stay mode. KeyBoB’s internal
buzzer will emit 5 short beep sounds, LED indicator (red
and green) will light up, conrming a transferred command
to ELDES alarm system via wireless connection. Other-
wise, key fob’s internal buzzer will emit 1 long beep sound
and LED indicator (red) will light up or ash quickly, inform-
ing user about unsuccessful attempt to transfer command
(due the system’s violation (action failed) or the wireless
connection loss (out of range)).
• Disarm – After the button is pressed, this function dis-
arms the system. KeyBoB’s internal buzzer will emit 2 long
beep sounds, LED indicator (green) will light up, conrming
a transferred command to ELDES alarm system via wire-
less connection. Otherwise, key fob’s internal buzzer will
emit 1 long beep sound and LED indicator (red) will ash
quickly, informing user about unsuccessful attempt to
transfer command (due to the wireless connection loss
(out of range)).
• Turn output ON – After the button is pressed, this func-
tion turns ON the selected PGM output. KeyBoB’s internal
buzzer will emit 1 quick beep sound, LED indicator (green)
will quickly ash once, conrming a transferred command
to ELDES alarm system via wireless connection (action
success). Otherwise, key fob’s internal buzzer will emit 1
long beep sound and LED indicator (red) will light up or
ash quickly, informing user about unsuccessful attempt
to transfer command (due to the system’s violation (action
failed) or the wireless connection loss (out of range)).
• Turn output OFF – After the button is pressed, this func-
tion turns OFF the selected PGM output. KeyBoB’s internal
buzzer will emit 1 quick beep sound, LED indicator (green)
will quickly ash once, conrming a transferred command
to ELDES alarm system via wireless connection (action
success). Otherwise, key fob’s internal buzzer will emit 1
long beep sound and LED indicator (red) will light up or
ash quickly, informing user about unsuccessful attempt
to transfer command (due to the system’s violation (action
failed) or the wireless connection loss (out of range)).
• Toggle (Output) – After the button is pressed, this func-
tion changes the status of the selected PGM output (ON or
OFF, depending on the previous status). KeyBoB’s internal
buzzer will emit 1 quick beep sound, LED indicator (green)
will quickly ash once, conrming a transferred command
to ELDES alarm system via wireless connection (action
success). Otherwise, key fob’s internal buzzer will emit 1
long beep sound and LED indicator (red) will light up or
ash quickly, informing user about unsuccessful attempt
to transfer command (due to the system’s violation (action
failed) or the wireless connection loss (out of range)).
• Panic alarm – After the button is pressed, this function
triggers virtual panic alarm (NOTE: this action is available
only for Long Press setting). LED indicator (red) will light
up and therefore conrm a transferred command to ELDES
alarm system via wireless connection, while KeyBoB’s in-
ternal buzzer will remain silent (in case when Panic action
is set, key fob’s buzzer is always disabled due to security
reasons). Otherwise,key fob’s LED indicator (red) will ash
quickly, informing user about unsuccessful attempt to
transfer command (due to the wireless connection loss
(out of range)).
• Pulse ON output – PGM output state will be instantly
changed (turned ON) for a determined time period and
automatically turned OFF when the time period expires.
• Pulse OFF Output – PGM output state will be instantly
changed (turned OFF) for a determined time period and
automatically turned ON when the time period expires.
4. PAIRING KEY FOB WITH ALARM SYSTEM
In order to pair the device with the alarm system, you’ll
have to complete the following:
1) Run ELDES Utility software.
3) In software’s menu, open Peripheral Devices section
to see the list of all wireless devices;
2) When in Peripheral Devices section, press the key fob
button one time (any button on your key fob) and
your key fob will instantly appear in the list;
3) Click Add to System button, located next to the un-
paired wireless key fob icon (grey icon);
4) Press the key fob button (again, any button on your
key fob) once to complete the pairing process.
5) If the pairing is successful, key fob’s LED indicator
(green) will light up, and the icon next to the device will
turn GREEN.
6) Your KeyBob is ready for use.
NOTE: If you are unable to pair the wireless device,
please restore the parameters of the wireless
device to default and try again (see chapter 6.
RESTORING DEFAULT PARAMETERS).
KeyBoB
WIRELESS Key fob
EN

5. BATTERY REPLACEMENT
1. Open key fob’s enclosure.
2. Remove the old battery from the battery slot.
3. Insert the new battery according to the appropriate po-
larity of the battery.
4. Battery is replaced.
6. SAFETY INSTRUCTIONS
Please read and follow these safety guidelines in or-
der to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with
other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical
environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
ATTENTION: Only CR2450 3V or CR2320 3V (with
specially adapted battery holder) battery can be used.
Install only new, high quality and unexpired batteries.
ATTENTION: In order to avoid re or explosion haz-
ards, special care must be taken when connecting posi-
tive and negative battery terminals. Dispose old bat-
teries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-
time using ELDES Utility software.
7. RESTORING DEFAULT PARAMETERS
1. Launch Eldes Utility software, go to Peripheral Devices
section, remove previously added key fob by clicking Re-
move, located next to the paired wireless device icon.
2. Press and hold and buttons simultane-
ously.
3. Hold those buttons pressed (approx. for 10 seconds) un-
til LED indicator (red) and the buzzer provide several short
ashes and beeps simultaneously.
4. Release the buttons.
5. Default parameters are restored.
8. ADDITIONAL INFORMATION
Warranty procedures
Warranty and out of warranty service should be obtained
by contacting the system integrator/dealer/retailer/ e-
tailer or distributor where the customer purchased the
product. When requesting for service, the proof of pur-
chase and the product serial number must be provided.
The return of the defective product should be strictly
through the original route of purchase, and the custom-
ers shall pack the product appropriately to prevent the
returned product from suering in the transportation.
Technical support
In order to ensure continuous and proper operation of Key-
BoB device and uninterrupted service, it is the responsibil-
ity of the User to make sure that: (I) the product is properly
installed, and (II) there is constant internet or GSM connec-
tion and electrical supply (low battery must be replaced in
time). If you experience diculty during the installation or
subsequent use of the system, you may contact ELDES, JSC
distributor or dealer in your country/ region. For more infor-
mation see eldesalarms.com
Limited Liability
The buyer must agree that the system will reduce the
risk theft, burglary or other dangers but does not provide
guarantee against such events. ELDES, JSC will not assume
any responsibility regarding personal or property, or rev-
enue loss while using the system. ELDES, JSC will also as-
sume no liability due to direct or indirect damage or loss,
as well as unreceived income when using the system, in-
cluding cases, when the damages arise due to the above
mentioned risks; when due to breakdown or malfunction
the user is not informed in a timely manner about a risk
which has arisen. In any case, the liability of ELDES, JSC, as
much as it is allowed by the laws in force, shall not exceed
the price of acquisition of the product.
Manufacturer Warranty
ELDES, JSC warrants this system only to the original pur-
chaser and only in case of defective workmanship and
materials under normal use of the system for a period of
twenty four (24) months from the date of shipment by
ELDES, JSC (Warranty Period). Warranty obligations do
not cover expandable materials (power elements and/or
batteries), holders and enclosures. The warranty remains
valid only if the system is used as intended, following all
guidelines outlined in this manual and in accordance with
the operating conditions specied. The warranty is void
if the system has been exposed to mechanical impact,
chemicals, high humidity, uids, corrosive and hazardous
environments or force majeure factors.
Consumer protection laws
FOR CONSUMERS WHO ARE COVERED BY CONSUM-
ER PROTECTION LAWS OR REGULATIONS IN THEIR
COUNTRY OF PURCHASE OR, IF DIFFERENT, THEIR
COUNTRY OF RESIDENCE, THE BENEFITS CONFERRED
BY THIS WARRANTY ARE IN ADDITION TO ALL RIGHTS
AND REMEDIES CONVEYED BY SUCH CONSUMER
PROTECTION LAWS AND REGULATIONS. This war-
ranty grants upon you specic legal rights, and you
may also have other rights that vary by country, state
or province.
Copyright © ELDES, JSC,
2020. All rights reserved
It is strictly forbidden to copy and distribute the
information contained in this document or to
pass thereof to a third party without an a priori
written authorization obtained from ELDES,
JSC. ELDES, JSC reserves the right to update or
modify this document and/or related products
without an a priori warning. ELDES, JSC hereby
declares that the mentioned product KeyBoB
(certied as EWK3) is in compliance with the es-
sential requirements and other relevant provi-
sions of the Directive RED 2014/53/EU, Annex
III. The certicate is available at:
www.eldesalarms.com/keybob
The WEEE (Waste Electrical and Electronic
Equipment) symbol on this product (see
left) means it must not be disposed of in
household waste. To prevent possible harm
to human health and/or the environment,
you must dispose of this product in an ap-
proved and environmentally safe recycling
facility. For further information contact
your system supplier, or your local waste
authority.