Champ SG300RFM User manual

SG300RFM
WIRELESS HAND HELD SCANNER
User Manual

1
We Value Your ID’s.
Notice
The manufacturer shall not be liable for technical or
editorial errors or omissions contained herein; nor for
incidental or consequential damages in connection with
the furnishing, performance or use of the publication.
EMEA
SCANTECH-ID BV
Amersfoortsestraat 124
3769 AN Soesterberg
The Netherlands
Tel:[phone]
Fax:[phone]
E-mail:[email protected]
www.scantech-id.com
CHINA
CHAMPTEK INCORPORATED
#901, No. 39, Wuzhong Rd., Shanghai
200235, China
Tel: [phone]
Fax: [phone]
HQ
CHAMPTEK INCORPORATED
5/F, No.2 Alley 2, Shin-Wei Lane,
Chung Cheng Rd., Hsin Tien City 231,
Taipei, Taiwan
Tel:[phone]
Fax:[phone]
E-mail:[email protected]
www.champtek.com

2
Content
1.Safety & Caution ....................................................................1
2.FCC Warning..........................................................................2
3.Introduction.............................................................................3
3.1 Product Description.....................................................3
3.2 Shipment Package......................................................3
3.3 Product Portfolio..........................................................3
3.4 Illustration....................................................................4
3.5 Cradle Installation To The Host Device.......................5
3.6 Cradle/Dongle Installation...........................................8
3.7 Indicator Status ...........................................................9
3.8 Environment Requirement ..........................................9
4.Specification.........................................................................10

1
Safety & Caution
1. Please read the following safety statement carefully.
2. Please preserve this user manual for reference sometime.
3. Before cleaning SG300RFM, the users must cut off all AC
power. Do not use liquid or spray type of detersive to clean
SG300RFM. Please use dampish cotton cloth to clean
SG300RFM.
4. The outlet must be set nearby SG300RFM for connecting
power easily.
5. Keep SG300RFM dry to avoid short circuit.
6. During installation, you must fix this equipment at solid table
to avoid damage caused by falling .
7. Before inserting power please ensure the voltage is healthy
to the equipment.
8. For safety please tie wire well and don’t put anything on the
wire.
9. If you don’t use this equipment for long time, please cut off
the power to avoid damage from surge power.
10. Don’t spray any liquid on this machine because it may cause
a fire or short circuit.
11. Please do not open the equipment. For safety only the
qualified serviceman can open the equipment.
12. If there are the following situations please contact with the
qualified serviceman to check this equipment.
(a) The damage of wire or pin of power supply.
(b) Some liquid infiltrate into the equipment.
(c) The equipment has been exposed to wet environment.
(d) The equipment can’t work well.
(e) The equipment has any obvious damage, making the
SG300RFM working abnormally.
13. Don’t storage SG300RFM at the temperature lower then
-20℃(-4°F) or higher then +70℃(158°F) to avoid any
damage.
1

2
FCC Warning
This equipment complies with the requirements in Part 15 of
FCC.
Any operation must complies with the conditions below:
(a) The equipment will not cause any severe interference.
(b) The equipment can avoid any interference from
environment.
Statement:
This product is classified as A class product.
In environment this product may cause some
interference. In this situation the user may do
something to avoid interference.
2

3
Introduction
3.1 Product Description
This wireless hand-held long-range CCD scanner features a
freedom of scanning without the limitation of cable. Thanks to
the user-friendly two-way communication, the operator will be
alarmed if the scanned result was not reached the receiving
Cradle. With the most advanced narrow-band RF technology,
this scanner can be operated at 15 Meters range(Open space)
and features one Cradle that supports multiple
scanners (Maximum 8 scanners). The receiving Cradle includes
RF receive module and Batteries charger.
SG300RFM packaging comes with complete package including
scanners (one or more, max to 8 scanners), receiver and power
supply. Be suitable for any location where a scanning for long
distance is needed. The shipment package has two types:
“Master” and “Salve” those packages as following:
(P.S: First time using please charge the battery for 8 hours.)
3.2 Shipment Package
A.Master：
a. Hand-held wireless scanner(Include Lithium-ion Battery)
b. Wireless receiving cradle
c. Power adaptor
d. User manual
e. Programming Menu
f. Cable(One of three interface:RS232, Keyboard, USB)
B.Slave：
a. Hand-held wireless scanner
b. Rechargeable Cradle*1 (only recharge function)
c. Power adaptor
3.3 Product Portfolio
Portfolio Product content
One to one 1 Master
One to two 1 Master + 1 Slave
One to four 1 Master + 3 Slave
If the package is incomplete or something broken, please
contact the local agent or sales representative immediately.
3

4
3.4 Illustration
Master
Slave

5
3.5 Cradle Installation To The Host Device
RS232
1. Turn off the host device.
2. Connect the 10-pin RJ45 male connector into the 10-pin
modular jack on the bottom of the cradle.
3. Connect the 9-pin D-type Female connector of the RS232
cable to the proper COM port of the host device.
4. Plug the external power supply into the power jack on the
bottom of the cradle.
5. Plug the power supply into the AC outlet. The red LED on
the rear of the cradle will stay on.
6. Turn on the host device.

6
Keyboard Wedge
1. Turn off the host device.
2. Connect the 10-pin RJ45 male connector into the 10-pin
modular jack on the bottom of the cradle.
3. Disconnect the keyboard from host.
4. Connect the “Y” ends of the communication cable to the
keyboard and keyboard port on the host device. If necessary,
use the male/female adapter cable supplied with the scanner
for the proper connections.
5. Plug the external power supply into the power jack on the
bottom of the cradle.
6. Plug the power supply into the AC outlet. The red LED on the
rear of the cradle will stay on.
7. Turn on the host device.
8. Establish communication between the scanner and cradle.

7
USB
1. Turn off the host device.
2. Connect the 10-pin RJ45 male connector into the 10-pin
modular jack on the bottom of the charger cradle.
3. Connect the USB A type connector to the USB port on the
host device.
4. Plug the power supply into the power jack on the bottom of
the cradle.
5. Plug the power supply into the AC outlet. The red LED on the
rear of the cradle will stay on.
6. Turn on the host device.
7. Establish communication between the scanner and cradle.

8
3.6 Cradle/Dongle Installation
Skip resistant Pad position.
Connect cable and adaptor and lock up the iron panel. The
other side of cable will be connected with Host PC.
Lock the iron panel of Cradle by screwdriver.
.

9
3.7 Indicator Status
Operating status of LED and Sound indicator is shown as below.
Light SIGNAL STATUS
1 Blink and 1 beep Good Read
2 Blink and 2 beeps Good Read
But Transmit Fail
Green 4 Blink 2 times and 4
beeps 2 times Battery Need To Charge
Continuous on In Charging
a) Scanner
Red Off Charging Finished
Light SIGNAL STATUS
Green 1 Successful Transmission Follow
with 1 Blink Good Transmission
Red Continuous on Power on
b) Receiver
Yellow 1 Failed Transmission Follow
with 1 Blink Failed Transmission
3.8 Environment Requirement
Software
Operation System：win 98 / 2000 / XP / Vista
Hardware
I. Interface: RS232, KBW, USB
II. Power Supply: 5V
P.S. The setting of SG300RFM has been set before shipment.
It can plug and play without any setting. (Other settings
please refer to Programming menu.)

10
Specification
Electrical Characteristics
Supply Voltage DC +3.7V ±5%
Battery Type Li-ion battery (1100mAh)
Recharge Time 5 Hours
Operating 30,000 times scan at
continuous mode
Current Draw
Power On (Typ.) 180mA
Stand by (Typ.) 0.1mA
a) Scanner
Operation (Typ.) 180mA
Supply Voltage DC +5V ±5%
Current Draw
Power On (Typ.) 60mA
Stand by (Typ.) 60mA
b) Receiver
Operation (Typ.) 60mA
Performance Light Source 639 nm Red LED
Sensor Linear CCD Sensor
Processor Type 8051 compatible
Operating Freq. 36.864 MHz
Scan Rate 270 scans/sec
Reading Distance 270 mm
Width of Field 80 mm
Print Contrast Ratio PCS [email protected]mm
Resolution 0.1mm @ PCS 0.9
Ambient Light 100000 Lux Max. @
Direct sun light
ReadingAngle Test Conditions:Code
39, 10mil, PCS 0.9
Forward & Backward ± 70 Degree
Left & Right ± 60 Degree
a) Scanner
Characteristics
Dead Zone ± 5 Degree
Frequency Baud 426MHZ~442MHZ
/1MHZ step
Frequency Stability ±30KHZ @ -20oC
~+85oC
Modulation Method FSK (Frequency Shift
Keying)
Working BandWidth Below 250KHz
Data Rate 19.2Kbps
Stray Power -50dBm
Emission Power 3.5±1dBm
Receiving Sensitivity ≦-90dBm
b) Radio
Characteristics
Radio Range 15m for Open Air
Environmental
Operating Temperature -10 oC to 40 oC (32 oF to 102 oF)
Storage Temperature -20 oC to 70 oC (-4 oF to 158 oF)
Relative Humidity 20% to 95% (Non-condensing)
4

11
Readable Symbologies
Readable Default Enable
All UPC/EAN/JAN V V
EAN128 Code V V
Code 39 V V
Code 39 Full ASCII V
Code32 / Italian Pharmacy V
Code 128 V V
CODABAR/NW7 V V
Interleave 25 V V
Industrial 25 V
Matrix 25 V
MSI/PLESSEY V
Telepen V
Code 93 V
Code 11 V
China Postage V
RSS-14 V
RSS Limited V
RSS Expanded V
Reliability
Life Time
Light Source 40,000 hours
Trigger Switch 1,000,000 times
MTBF(Calculated) N/D
Thermal Shock
High Temp. 50 oC (122 oF)
Low Temp. -20oC (-4 oF)
Cycle time 7 minutes for high temp. , 7 minutes for low temp.
Cycles 24 cycles
Mechanical Shock 40inch (100 cm) drops on Concrete Surface
Battery charge time 500 times
Safty CE, FCC
Packing
Dimension
Unit 27.5 cm X 11.5 cm X 14 cm
Carton 55.5 cm X 49 cm X 30 cm
Weight
Unit N.W. 654g (USB)
Unit G.W. 766.4g (USB)
Carton 13.26Kg ( Q’ty :16 pcs 1 to 1) (USB)
Storage
Temperature -20
oC to 70 oC (-4 oF to 158 oF)
Humidity 20% to 95% (Non-condensing)
Product Frequency P/N
Receiver P/N Receiver 434MHZ 7185

12

0
SG300RFM
無線手持式條碼掃瞄器
操作說明書

1
We Value Your ID’s.
版權宣告
阿丹電子企業股份有限公司有權更改本手冊的內容，如手冊內容與實際產品不符，以
實際產品為準，恕不另行通知。沒有本公司的書面許可，您不得為任何目的而使用任
何形式或方法（電子或機械）複製或傳送本手冊的任何部分。
分公司/營業處 (歐洲)
SCANTECH-ID BV
Amersfoortsestraat 124
3769 AN Soesterberg
The Netherlands
Tel:[phone]
Fax:[phone]
E-mail:[email protected]
www.scantech-id.com
營業處 (中國區)
阿丹貿易(上海)有限公司
中國上海市徐匯區吳中路39號901室(郵編 200235)
Tel: [phone]
Fax: [phone]
總公司/工廠/營業處 (亞洲)
阿丹電子企業股份有限公司
臺灣台北縣新店市(231)中正路四維巷 2弄2號5F
Tel:[phone]
Fax:[phone]
E-mail:[email protected]
www.champtek.com

2
目錄
1.安全注意事項..........................................................................1
2.FCC 安全警告.........................................................................2
3.產品介紹.................................................................................3
3.1 產品說明......................................................................3
3.2 出貨說明......................................................................3
3.3 組合方式......................................................................3
3.4 圖示說明......................................................................4
3.5 連線方式......................................................................5
3.6 接收器/充電座 蓋板安裝方式 ......................................8
3.7 燈號及警示音說明........................................................9
3.8 工作環境需求...............................................................9
4.產品規格...............................................................................10

1
安全注意事項
安全與警告
1. 請仔細閱讀以下安全說明。
2. 請保存好此使用手册以供日後参考。
3. 在清潔本產品之前，首先要切斷所有電源，不要用液體或是
氣體清潔劑進行清洗，使用微濕的棉布清潔即可。
4. 電源插座必須安裝在本產品附近，以方便接通電源。
5. 保持設備乾燥，以防潮濕。
6. 安裝過程中，須將本產品放置在穩定的桌面，若發生跌落將
會造成損壞。
7. 在連接電源之前請確認產品使用電壓與電源電壓是否相同。
8. 請將電源線綁好，以防止被踩到，不要在電源線上放置任何
物體。
9. 請認真閱讀產品上的任何小心和警告内容。
10. 如果長時間不使用本產品，請切斷電源以防瞬間高壓衝擊造
成損害。
11. 請不要在機器上倒任何液體，因為可能導致火花或是電源短
路。
12. 請不要拆卸本產品，基於安全的原因，只有專業資格的維修
人員才能拆卸本產品。
13. 如有以下情况發生，請專業維修人員檢查本產品：
(a)電源線或者插頭損壞
(b)有液體渗入產品内部
(c)產品已經暴露在潮濕的環境中
(d)產品不能正常工作，或者不能使其按照使用說明手冊方
式使其正常工作
(e)產品跌落或是損害
(f)產品有任何明顯損壞的跡象
14. 不要將產品儲存在温度低於-20℃(-4°F)或者高於+70℃(158°F)
的環境中，以免造成損壞。
1

2
FCC 安全警告
依據 FCC 規範的第 15 部分，本產品已經過測試並符合 Class A 裝
置之限制要求。
這些限制是設計用來提供合理的保護，以避免居住環境遭受電波
干擾傷害。此裝置產生、使用並能夠散發無線電頻率能量，若是
未依照指示進行安裝或是使用時，可能會引起電波通信干擾的問
題產生。然而，我們並不保證在某些特定安裝情況時，將不會發
生干擾問題。
FCC警告：
更改或是變更此裝置是不被允許的，因為契約中
的承諾可能會造成使用者喪失操作此裝置的權
力。
2