Chard HZB-15/BF User manual

USER MANUAL
ICE MAKER
Model: HZB-15/BF
HZB-22/BF
INSTRUCTION MANUAL
It is important that you read these instructions before using your portable ice maker and we
strongly recommend that you keep them in a safe place for future reference.

1
IMPORTANT SAFETY INSTRUCTIONS……………………………………………….…2
PREPARING YOUR ICE MAKER FOR USE
IMPORTANT SAFETY TIPS…………………………………………………………………….3
GETTING TO KNOW YOUR UNIT………………………………………………………..5
OPERATING PROCEDURES & MAINTENANCE………………………………………6
UNPACKING YOUR ICE MAKER………………….…………………………………………...6
CONNECTING YOUR ICE MAKER……………….……….…………………………………...7
CLEANING AND MAINTAINING YOUR ICE MAKER….………………………………………..7
USING YOUR ICE MAKER……………….……..………………………………………...8
TROUBLESHOOTING…………………………….……………………………………………9
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM……………………..….………..9
TABLE OF CONTENTS
TABLE OF CONTENTS

2
DANGER
WARNING
Your safety and the safety of others are very important.
We have provided many important safety messages manual and your appliance.
Always read and obey all safety messages.
This is the safety alert symbol:
!
All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.
These words mean:
You can be killed or seriously injured if you don’t immediate follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance
of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS

3
When using electrical appliances, basic safety precautions should be followed to reduce the
risk of fire, electric shock, and injury to persons or property. Read all instructions before using
any appliance.
Do not operate this，or any other appliance with a damaged cord.
Connect to properly polarized outlets only. No other appliance should be plugged into the
same outlet. Be sure that the plug is fully inserted into the receptacle.
Do not run the power cord over carpeting or other heat insulators. Do not cover the cord.
Keep cord away from traffic areas, and do not submerge in water.
We do not recommend the use of an extension cord, as it may overheat and become a risk
of fire. If you must use an extension cord, use No.14 AWG minimum size and rated no less
than 1875 watts.
Unplug the ice maker before cleaning or making any repairs or servicing.
Exercise caution and use reasonable supervision when appliance is used near children.
Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and
make sure that there is at least 4 inches of space between the back of your unit and wall.
Keep a minimum distance of 4 inches on each side of your unit free.
Do not use other liquid to make the ice-cube other than water.
Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or
explosion.
Do not tip over.
If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to
room temperature before plugging it in.


DANGER – Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use Mechanical
Devices To Defrost Ice Maker. Do Not Puncture Refrigerant Tubing.
CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair Manual
/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions
Must be Followed.
DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be
Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
PREPARING YOUR ICE MAKER FOR USE
IMPORTANT SAFETY TIPS

4
CAUTION – Risk Of Fire Or Explosion. Dispose Of Property In Accordance With Federal Or
Local Regulations. Flammable Refrigerant Used .
CAUTION-Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing;Follow Handling
Instructions Carefully. Flammable Refrigerant Used.
The ice maker should be installed in accordance with the safety standard for Refrigeration
Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public
buildings.
If the unit is with problem need to be maintained, that replacing with like components and
that servicing shall be done by factory authorized service personnel, so as to minimize the
risk of possible ignition due to incorrect parts or improper service.
WARNING: This appliance must be earthed.
WARNING: fill with potable water only.
IMPORTANT:
The wires in this mains lead are colored in accordance with the following code:
Green or Green with a strip yellow: Grounding
White: Neutral
Black: Live
To avoid a hazard due to instability of the appliance, it must be placed at a even or flat
surface.

5
UNIT
SMART CORE FOR
THE WATER BOTTLE
ICE CUBE BASKET
OPERATION PANEL
WATER DRAIN CAP
(Need to be pop up by the button
near the operation panel)
COLD WATER FAUCET
AIR OUTLET
Can be pulled out
BUTTON TO POP UP
THE WATER FAUCET
OPERATION PANEL
Small Size of
Ice-cube Light
Medium Size of
Ice-cube Light
Large Size of
Ice-cube Light
Water Dispensing Button
ICE-FULL Indicating Light
Means that there is no
water in the unit
WATER Indicating Light
POWER Indicating Light
Use to start or stop
the unit
Use to select the desired
size of the ice-cube.
ON/OFF Button
SELECT Button
GETTING TO KNOW YOUR UNIT

6
1. Remove the exterior and interior packaging. Check that ice scoop is included. If any parts
are missing, please contact our customer service.
2. Clean the interior with lukewarm water and a soft cloth. Take out the ice basket and clean
it .
3. Find a location for your ice maker that is protected from direct sunlight and other sources of
heat (i.e.: stove, furnace, radiator). Place the ice maker on a level surface. Maker sure that
there is at least 4 inches of space between the back and sides of your ice maker and the
wall.
4. Allow one hour for the refrigerant fluid to settle before plugging ice maker in.
5. The appliance must be positioned so that the plug is accessible.
6. Before placing water bottle on the unit, be sure that the drain plug on the back is tightly
fastened.
7. Hold the water bottle vertically and upside down (over the unit) and place the water bottle
into the SMART CORE for the water bottle. Apply slightly pressure in order to pierce the
bottle cap with the spigot. This unit accepts two, three or five gallon water bottle with
pierceable sealed caps.
PLACE BOTTLE
VERTICALLY
STRAIGHT DOWN
OPERATING PROCEDURES & MAINTENANCE
UNPACKING YOUR ICE MAKER

7
DANGER
* Improper use of the grounded plug can result in the risk of electrical shock. If the
power cord is damaged please call our customer service.
1. This unit should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug which mates with standard three prong wall outlets to
minimize the possibility of electric shock.
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under
any circumstances, cut or remove the third (ground) prong from the power cord. Any
questions concerning power and/or grounding should be directed toward a certified
electrician.
3. This appliance requires a standard 110~120 volt, 60Hz electrical outlet with three-prong
ground.
Before using your ice maker, it is strongly recommended to clean it thoroughly.
1. Take out the ice basket.
2. Clean the interior with diluted detergent, warm water and a soft cloth.
3. Then use the water to rinse the inside parts, and drain out the water by unplugging the
drain cap on the side.
4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and
warm water.
5. Dry the interior and exterior with a soft cloth.
6. When the machine is not in use, open water drained cap to drain water completely from
water reservoir.
CONNECTING YOUR ICE MAKER
CLEANING AND MAINTAINING YOUR ICE MAKER

8
MAKING THE ICE -CUBE
1. Select the size of the ice cube by pressing the “Select” button. If the room temperature is
lower than 60℉, it is recommended to select the small or medium ice sign button in order to
avoid ice sticking together.
2. Press “Power” on the control panel to begin the ice making cycle.
3. The ice making cycle lasts 6 to 12 minutes, depending on the size of the ice cube selection.
4. If water pump can’t inject water, the ice maker will stop automatically, and the “ADD
WATER” indicator will be on on the operation panel. Please check the water bottle and
replace a new bottle full of water.
Press “Power” button again to start the unit again.
Allow the refrigerant liquid inside the compressor at least 3 minutes to settle before
restarting.
5. The ice maker automatically stops working when the ICE light on the operarion panel is on
means that ice basket is full.
ENJOY THE COLD WATER ( For HZB-15/BF model only)
The cold water can be enjoyed only after the ice-making have worked for more than half hour.
1. Press the button to pop up the cold water faucet.
2. Press the “WATER” Water Dispensing Button on the operation button to dispense the
cold water to your cup. Release pressing till your cup is full of the cold water.
Push this button to
let the cold water
faucet pop up.
USING YOUR ICE MAKER

9
Model
HZB-15/BF
HZB-22/BF
Description Ice maker using bottled water, with cold water dispensing function
Power Rating 115V~, 60Hz
Ice-making Rated Current 2.0A
Ice-harvest Rated Current 2.7A
Refrigerant R290 1.16Oz/33g
Design Pressure High Side 290Psig
Low Side 88Psig
Enclosure Stainless steel or cold rolled sheet metal steel with plastic cover
Dimension 357mm(W)*423mm(D)*452mm(H)
Net Weight 15.2Kg
PROBLEM POSSIBLE CAUSE SOLUTION
“Water” indicator is on. Lack of Water.
Stop the ice maker, replace with a
new bottle full of water, and then
restart it.
“Ice” indicator is on. The ice basket is full of the
ice-cube. Pull the ice basket and empty it.
Ice cubes stick together.
The ice cycle is too long.
Stop the ice maker, and restart it
when the ice blocks melt. Select
the small ice button.
Water temperature in inner
tank is too low.
Change the water in the inner
Tank. Temperature of water is
better set between 45℉-90℉.
Ice making cycle is normal
but no ice is made.
Ambient temperature or
water temperature in inner
tank is too high.
Please run the ice maker below
90 ℉and pour colder water into
tank.
Refrigerant liquid leakage. Verify by a qualified technician.
Pipe in the cooling system
is blocked. Verify by a qualified technician.
TROUBLESHOOTING
TECHNICAL PARAMETERS
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM

10
CIRCUIT DIAGRAM