Cornelius IMD GLACIER 500-30 User manual

COUNTERTOP ICE MAKER IMD GLACIER SERIES
Installation Manual
Release Date: May 11, 2018
Publication Number: 620068501INS
Revision Date: May 11, 2018
Revision: A
Visit the Cornelius web site at www.cornelius-usa.com for all your Literature needs.

The products, technical information, and instructions contained in this manual are subject to change without notice.
These instructions are not intended to cover all details or variations of the equipment, nor to provide for every possible
contingency in the installation, operation or maintenance of this equipment. This manual assumes that the person(s)
working on the equipment have been trained and are skilled in working with electrical, plumbing, pneumatic, and
mechanical equipment. It is assumed that appropriate safety precautions are taken and that all local safety and con-
struction requirements are being met, in addition to the information contained in this manual.
This Product is warranted only as provided in Cornelius’ Commercial Warranty applicable to this Product and is sub-
ject to all of the restrictions and limitations contained in the Commercial Warranty.
Cornelius will not be responsible for any repair, replacement or other service required by or loss or damage resulting
from any of the following occurrences, including but not limited to, (1) other than normal and proper use and normal
service conditions with respect to the Product, (2) improper voltage, (3) inadequate wiring, (4) abuse, (5) accident, (6)
alteration, (7) misuse, (8) neglect, (9) unauthorized repair or the failure to utilize suitably qualified and trained persons
to perform service and/or repair of the Product, (10) improper cleaning, (11) failure to follow installation, operating,
cleaning or maintenance instructions, (12) use of “non-authorized” parts (i.e., parts that are not 100% compatible with
the Product) which use voids the entire warranty, (13) Product parts in contact with water or the product dispensed
which are adversely impacted by changes in liquid scale or chemical composition.
Contact Information:
To inquire about current revisions of this and other documentation or for assistance with any Cornelius product contact:
www.cornelius.com
800-238-3600
Trademarks and Copyrights:
This document contains proprietary information and it may not be reproduced in any way without permission from
Cornelius.
This document contains the original instructions for the unit described.
CORNELIUS INC
101 Regency Drive
Glendale Heights, IL
Tel: + 1 800-238-3600
Printed in U.S.A.
Correct Disposal of this Product
RECYCLE
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this product for environmental safe
recycling.

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. Publication Number: 620068501INS
TABLE OF CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Read and Follow ALL Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Different Types of Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Qualified Service Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Shipping And Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mounting in or on a Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Noise Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Fire Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remove Ice maker from Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacked Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cabinet Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Auger Engagement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation of Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Water Inlet Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Drain Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Initial Start Up, Checks & Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cabinet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Guide To Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ice maker Cleaning and Sanitizing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Monthly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Quarterly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Semi-Annually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Water Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
How Water Level Control Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Purpose of Water Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To Replace Water Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To Replace Water Level Safety Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ice Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Refrigeration System Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Adjustment and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gear Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auger & Extruding Head Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation And Shaft Seal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Upper Nut and Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To Replace Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS © 2018, Cornelius Inc.
Troubleshooting Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Electrical Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Overload Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Compressor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Capacitor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting Gear Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The Gear motor will not run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The Gear motor Starts but Trips Repeatedly on the Overload Protector . . . . . . . . . . . . . . . . . 25
The Motor Runs but Output Shaft does not Rotate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Overload Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Motor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Safety Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Guide To Good Ice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Trouble shooting instructions for IMD Gacier 500-30, 230v / 50Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Trouble Shooting Instructions for IMD Gacier 600-30, 115v / 60hz . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Wiring Schematic for IMD Gacier 500-30, 230v / 50hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Wiring Schematic IMD Glacier 600-30, 115v / 50hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Motor Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 1 - Publication Number: 620068501INS
SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Safety Overview
• Read and follow ALL SAFETY INSTRUCTIONS in this manual and any warning/caution labels on the unit
(decals, labels or laminated cards).
• Read and understand ALL applicable OSHA (Occupational Safety and Health Administration) safety regu-
lations and/or national and local codes before operating this unit.
Recognition
Different Types of Alerts
!
DANGER:
Indicates an immediate hazardous situation which, if not avoided, WILL result in serious injury, death or equipment
damage.
!
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in serious injury, death, or equipment
damage.
CAUTION:
!
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury or equipment
damage.
SAFETY TIPS
• Carefully read and follow all safety messages in this manual and safety signs on the unit.
• Keep safety signs in good condition and replace missing or damaged items.
• Learn how to operate the unit and how to use the controls properly.
• Do not let anyone operate the unit without proper training. This appliance is not intended for use by very
young children or infirm persons without supervision. Young children should be supervised to ensure that
they do not play with the appliance.
• Keep your unit in proper working condition and do not allow unauthorized modifications to the unit.
NOTE: The dispenser is not designed for a wash-down environment and MUST NOT be placed in an area
where a water jet could be used.
Recognize Safety Alerts
This is the safety alert symbol. When you see it in this manual or on the unit, be
alert to the potential of personal injury or damage to the unit.
!

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 2 - © 2018, Cornelius Inc.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit. ALL WIRING
AND PLUMBING MUST CONFORM TO NATIONAL AND LOCAL CODES. FAILURE TO COMPLY COULD
RESULT IN SERIOUS INJURY, DEATH OR EQUIPMENT DAMAGE.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE
AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD.
SAFETY PRECAUTIONS
This unit has been specifically designed to provide protection against personal injury. To ensure continued protection,
observe the following:
!
WARNING:
Disconnect power to the unit before servicing following all lock out/tag out procedures established by the user. Verify
all of the power is off to the unit before any work is performed.
Failure to disconnect the power could result in serious injury, death or equipment damage.
CAUTION:
!
Always be sure to keep area around the unit clean and free of clutter. Failure to keep this area clean may result in
injury or equipment damage.
SHIPPING AND STORAGE
CAUTION:
!
Before shipping, storing, or relocating the unit, the unit must be sanitized and all sanitizing solution must be drained
from the system. A freezing ambient environment will cause residual sanitizing solution or water remaining inside the
unit to freeze resulting in damage to internal components.
MOUNTING IN OR ON ACOUNTER
!
WARNING:
When installing the unit in or on a counter top, the counter must be able to support a weight in excess of 400 lbs. (182
kg.) to insure adequate support for the unit.
Failure to comply could result in serious injury, death or damage to the equipment.
NOISE LEVEL
This unit emits acoustical noise with an A-weighted sound pressure level no greater than 75dB, as measured in
accordance with ED 60335-2-75.
FIRE HAZARD WARNING
!
WARNING:
50Hz unit contains a flammable refrigerant. Keep all flammable materials away from the compressor area. Always be
sure to keep the area around the unit clean and free of clutter. Failure to keep this area clean may result in a fire
hazard, injury or equipment damage.

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 3 - Publication Number: 620068501INS
!
WARNING:
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
!
WARNING:
Do not damage the refrigerant circuit.

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 4 - © 2018, Cornelius Inc.
GENERAL INFORMATION
Models Condensing
UnitVAC Hz Ph Comp
RLA
Fan
Amps Grmtr Amps
Refrigerant Circuit
Fuse
Oz. Grams Type
IMD Glacier
500-30
Air Cooled 220/
240
50 15.7 0.5 1.25 4.8 136 R290 20
IMD Glacier
600-30
Air Cooled 115 60 116 11.25 22 623.7 R404a 20
SPECIFICATION CHART
NOTE: Unit intended for use in a commercial environment for food service or similar application such as
restaurants, kitchens, cafeterias, convenience stores etc...
Shipping WT (IMD Glacier 500-30) 240 lbs (109 Kg’s). (APPROX)
Shipping WT (IMD Glacier 600-30) 240 lbs (109 Kg’s). (APPROX)
.
Figure 1. Dimension Drawing IMD Glacier 500-30/600-30
Dimensions shown in the [ ] are in mm.

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 5 - Publication Number: 620068501INS
INSTALLATION INSTRUCTIONS
REMOVE ICE MAKER FROM PACKAGING
1. Keep the unit in the upright position, first remove the top panel (No:1) of the wooden package by un-stapling/
un-screwing.
2. Remove the staples/screws from the right panel (No:2) of the package to remove the right side panel.
3. Remove the staples/screws from the left panel (No:3) of the package to remove the left side panel.
4. Remove the staples/screws from the front panel (No:4) of the package to remove the front panel.
5. Remove the staples/screws from the back panel (No:5) of the package to remove the back panel.
6. Remove the two bolt (No:6) that secures the unit on the pallet (Can be located at the bottom of the pallet). To
un-bolt it tilt the unit to its side (either left or right) so that the 3/8” (M10) bolts are easy to access.
NOTE: Make sure that the unit side is not touching the floor.
NOTE: To unbolt a Socket head wrench is needed.
7. Inspect the unit for damage, upon inspection of unit, if any damage is found, file a claim with carrier immedi-
ately.
8. Locate Start-up Card either on outside of container or on plastic liner. Fill in proper information and send one
copy to factory, and other copy to Distributor. Postage is prepaid.
NOTE: Do not lay the unit on its side or back. This may cause vital oils to drain from the compressor
resulting in damage during start-up and consequently voiding the warranty
Figure 2.

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 6 - © 2018, Cornelius Inc.
UNPACKED UNIT
Figure 3

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 7 - Publication Number: 620068501INS
CABINET REMOVAL
CAUTION:
!
Disconnect the power before removing the panels.
1. Un-screw the two screws as shown in Figure 4
on either side of the Ice Bin Cover. To remove
the ice bin cover hold it up firmly then lift the ice
bin cover up slightly and pull back.
Figure 4.
2. To Remove the splash panel-
a) Remove the ice chute cover first by removing
the two screws that secure it as shown in Figure 5
b) Un-screw the 3 screws that is shown in Fig-
ure 5A. To remove the splash panel cover hold it up
firmly then lift the splash panel up slightly and pull
back.
NOTE: Disconnect the dispense switch har-
ness after removing splash panel
from unit.
Figure 5
.
Figure 5A

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 8 - © 2018, Cornelius Inc.
3. Remove both the screws, as shown in Figure 6,
after unscrewing pull out the drip tray.
Figure 6.
4. Remove the top cover by pushing it back and
lifting it up as shown in the Figure 7.
Figure 7.
Alternative : Only to remove the top cover
Unscrew the 4 screws and lift it up as shown in
Figure 7A.
Figure 7A

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 9 - Publication Number: 620068501INS
5. Remove all the six screw that secures both the
side panels from either side of the machine as
shown in Figure 8. To remove the panels pull
out the panel gently at the front side and slide it
back to dis-engage it.
NOTE: The side panel can also be removed
without having to remove the
Splash Panel & Ice Chute. By
removing the top cover as explained
in “Step 4” and removing the 6
screws holding side panel as shown
in Figure 8A
NOTE: Before Removing the top panel
remove the screw which is fixing
splash panel and top cover Shown
as S in Figure 8A.
Figure 8.
Figure 8A.

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 10 - © 2018, Cornelius Inc.
AUGER ENGAGEMENT
Be certain that auger is fully engaged to lower drive and that extruding head is fully engaged to evaporator before
running the unit / assembling the components back.
8. Assemble back the hopper / storage bin cover but do not put / tighten the screws yet.
9. All the parts need to be assembled back only after finishing the drain connection set-up and initial start-up and
adjustment.
6. Remove the storage bin cover by un-screwing
all the four screw as shown in Figure 9.
NOTE: Dis-engage the motor harness
before lifting up the top lid of bin.
7. Remove the cardboard / shipping insert from
the hopper as shown in the Figure 9A.
Figure 9
Figure 9A.

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 11 - Publication Number: 620068501INS
PREPARATION OF INSTALLATION SITE
The refrigeration system on air cooled units requires airflow, so a well-ventilated area should be chosen. Ice Maker
should not be placed in direct sunlight or in close proximity of any object placing additional heat load on
refrigeration system.
TOP LOUVERS ARE ONLY FOR IMD GLACIER 600-30
AIR OUT
AIR IN
AIR IN AIR OUT
Figure 10. Air Flow
1. Minimum clearance must be maintained, free of any obstruction, for air flow. Refer the below table for the clear-
ances required for the specific model.
Model Minimum Clearance required free of obstructions, in Inches (mm). Climate class
Top Sides Back
IMD Glacier 500-30 06 (152.4) 6 (152.4) T
IMD Glacier 600-30 12 (304.8) 6 (152.4) 6 (152.4)
!
WARNING:
Keep ventilation openings in the appliance enclosure or in the built-in structure, clear of obstruction.
2. With template provided make the necessary provisions in the counter (as shown in Figure 11 on page 14) for
drain. Provisions for water inlet & Electrical connections are available at rear side of the unit.

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 12 - © 2018, Cornelius Inc.
NOTE: Drain connection should be completed before step 3.
3. Units placed on a counter must either use minimum of 4 inch (101.6mm) high legs (Provided in the installation
kit along with the unit) or be sealed to the counter top all around the base except Drip Tray with NSF listed seal-
ant / food grade sealant as per local codes. To avoid disturbing the seal, complete the installation prior to seal-
ing.
WATER INLET HOOK-UP
1. Water Inlet - Fitting is a 1/4” (6.35mm) SAE male flare located at the rear of the unit. Connect water supply
with a 1/4” (6.35mm) or larger copper or flexible tubing.
CAUTION:
!
Unit must be installed with only potable water.
NOTE: A shut-off valve with a loop of additional tubing for service is recommended.
2. Water Pressure - Unless otherwise specified, the unit is designed to operate on water pressures between 10
P.S.I. (0.69 Mpa) and 90 P.S.I. (0.62 Mpa)A recommended water supply is with temperatures between
50° F - 90° F (10° C - 32° C) with a pressure between 20-70 p.s.i (0.138 - 0.48 Mpa).
NOTE: For pressures above 90 P.S.I. (0.62 Mpa) a regulator must be installed.
NOTE: This equipment must be installed with adequate backflow protection to comply with applicable
federal state and local codes.
3. Filter - IMF (Phosphate Feeder) Water Filters and Scale inhibitors are not recommended for use with the Con-
tinuous Flow Ice-Maker, Taste & Odour only should be used. Total dissolved solids in the water should be within
the below specified limit
MIN dissolved solids = 270 PPM(TDS).
Max dissolved solids = 500 PPM(TDS).
NOTE: Water inlet for the Ice Maker should not be with RO Filtration System.
NOTE: Unit must be installed per local plumbing code.
ELECTRICAL SUPPLY
1. Power Access - Connect the unit with power cord provided. An adapter plug for the particular country needs to
be provided by the installer.
2. Fused Line - Should be a dedicated circuit checked and sized according to electrical rating shown on unit
nameplate.
3. This unit should not be connected to a GFI / GFCI receptacle.
NOTE: Unit must be installed per local electrical code.
NOTE: This equipment is intended for use only in premises with a service current capacity > 100A per
phase. User and/or installer must determine the service capacity is sufficient, on consultation
with the supply authority is necessary.

Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 13 - Publication Number: 620068501INS
DRAIN CONNECTION
1. Complete the drain connection as per the Figure 12 or Figure 12A illustrated in page 15, by using the parts in
the installation kit provided along the unit.
2. Big oval cut out (1) on the counter below the drip tray is to pass the drain line from drip tray.
3. Circular cut out (2) at the center left on the counter top is to pass the drain line from hopper.
4. Above two drain lines can be connected to the floor drains separately or can be combined using the ‘Tee’ con-
nection given in the installation kit to make a single drain line to the floor.
5. When using the Elbow & Tee connections to make the joints between the drain lines ensure the joints are tight
and leak proof using the clamp provided in the installation kit.
NOTE: If the unit is mounted directly to the counter and not on the legs, it should be sealed all around
the base except Drip Tray using a NSF approved sealant.

Installation kit for recommended drain cutout
Refer the sheet 620068502 provided in the
MINIMUM CLEARANCE
Dimensions shown in the [ ] are in mm.
MINIMUM
CLEARANCE
MINIMUM
CLEARANCE
Refer “Minimum Clearance Table” provided on page No.11 for recommended minimum clearance.
Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 14 - © 2018, Cornelius Inc.
Figure 11. Counter Preparation

COUNTER
ELBOW
TUBING
T-FITTING
1”( 25.4MM)
TUBING
1/2” - 1”(12.7-25.4MM)
ELBOW
1”( 25.4MM)
Figure 12. Drain connection (Type 1)
COUNTER
ELBOW
T-FITTING
1”( 25.4MM)
TUBING
Figure 12A. Drain connection (Type 2)
Countertop Icemaker IMD Glacier Series Installation Manual
© 2018, Cornelius Inc. - 15 - Publication Number: 620068501INS
INITIAL START UP, CHECKS & ADJUSTMENT INSTRUCTIONS
NOTE: Do not start unit before completing above Installation Instructions.
Turn on water supply and main power switch (located on top of electric box). All IMD Glacier series units are
equipped with a 45 second delay timer. This means that the refrigeration system will not start until 45 seconds of
dispense are accumulated in the timer. Start the refrigeration system by depressing the ice dispense lever for 45
seconds. Make the following system checks:
NOTE: If unit will not start be sure water reservoir is full. Low water safety control must be properly
adjusted to start and shut down unit. If water level drops below bottom of reservoir, unit must
shut down. Adjustment is made by moving magnet up or down.
Water Level - If necessary, adjust float by bending float arm up or down as needed. Push float assembly down until
unit stops running. Release float and unit will restart. Keep water in reservoir at level line while unit is in operation.
See Figure 13 page No 16.

Countertop Icemaker IMD Glacier Series Installation Manual
Publication Number: 620068501INS - 16 - © 2018, Cornelius Inc.
Figure 13. Float Assembly
Low Water Safety Control - Adjust magnet by bending magnet arm as shown in Figure 13 to shut down unit if the
water level drops below the line on the side of the reservoir.
Bin Control - Lift the ice bin cover (Make sure ice bin cover screws are removed from the bin cover) so bin control
plate can be manually lifted until unit shuts down. Release plate and unit will restart. Replace screws.
Dispense Switch and Mechanism - By depressing the dispense lever, the dispense mechanism door on the stor-
age bin will open, and agitator will rotate counterclockwise.
NOTE: If any of these checks or adjustments cannot be achieved, refer to Troubleshooting Section of
this manual or call our Technical Support Center for assistance at 1-800-238-3600.
CABINET ASSEMBLY
After all the set-up and installation is completed and ensuring the unit is running and performing correctly start to
assemble the parts back.
1. Assemble back the Side Panels tightening all the (6) screws.
2. Slide back the Drip Tray to original position to assemble it with (2) screws.
3. Replace the Splash Panel & Top Cover and secure them with the (1 and 4) screws.
4. Fix the Ice chute cover back and tighten the (2) screws.
5. Replace the Ice-bin cover and tighten the (2) side screws.
6. Place the Ice Tray & Cup rest on the Drip tray from the installation kit provided.
Figure 14