Chatsworth Products CUBE-IT+ CABINET User manual

THIS STEP IS OPTIONAL, THE CABINET CAN BE
MOUNTED WITH THE REAR PANEL ATTACHED
1
STEP 1. DETERMINE WHICH SIDE THE CABINET WILL HINGE FROM. THE
CABINET IS SHOWN WITH THE HINGE ON THE LEFT SIDE, INVERT THE
CABINET IF YOU WANT THE HINGE ON THE RIGHT SIDE.
STEP 2. UNLOCK THE REAR FRAME AND OPEN IT TO GET ACCESS TO
THE HINGE BOLT NUTS.
STEP 3. REMOVE THE CENTER BOLT FROM THE BOTTOM HINGE ONLY.
LOOSEN THE OTHER TWO BOLT NUTS ON THE BOTTOM HINGE. DO
NOT REMOVE OR LOOSEN THE BOLTS ON THE TOP HINGE.
STEP 4. SLIDE THE BOTTOM HINGE PIN UP UNTIL THE LOOSENED
BOLTS REACH THE END OF THE SLOT. REMOVE THE REAR FRAME BY
MOVING THE BOTTOM OF THE FRAME TO THE REAR AND THEN
DOWNWARD TO DISENGAGE IT FROM THE TOP HINGE PLATE.
REMOVING REAR PANEL FROM CABINET
THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO
CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE
OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT
AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.
INSTALLATION
INSTRUCTIONS,
CUBE-IT+ CABINET
IIS-711890, SHEET 1 OF 4 - INSTALLATION INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS. 6 - CPI/BK
A
DETAIL A
REMOVE CENTER NUT FROM
INSIDE THEN REMOVE BOLT
SLIDE HINGE PIN UP
TO END OF SLOTS
LOOSEN NUTS FROM
INSIDE, DO NOT
REMOVE BOLTS

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO
CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE
OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT
AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.
INSTALLATION
INSTRUCTIONS,
CUBE-IT+ CABINET
IIS-711890, SHEET 2 OF 4 - ASSEMBLY INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS.6 - CPI/BK
16.00
31.87 FOR 36" HIGH CAB
44.12 FOR 48" HIGH CAB
19.62 FOR 24" HIGH CAB
MOUNTING REAR PANEL TO WALL
STEP 1. INSURE THAT THE WALL OR MOUNTING SURFACE HAS
SUFFICIENT STRENGTH TO SUPPORT THE CABINET AND
THE EXPECTED CABINET PAYLOAD. THE MOUNTING
SURFACE MUST ALSO BE FLAT AND EXTEND BEYOND THE
TOP, BOTTOM, LEFT, AND RIGHT EDGES OF THE REAR PANEL.
STEP 2. DRILL 11/64" PILOT HOLES FOR THE FOUR 1/4-10 X 2" LAG
SCREWS TO THE DIMENSIONS SHOWN ON THE DRAWING OR
USE THE MOUNTING TEMPLATE PROVIDED.
THE SCREWS SHOULD GO DIRECTLY INTO THE WALL STUDS.
STEP 3. INSTALL THE LAG SCREWS INTO THE HOLES. THE SCREW HEAD
SHOULD PROTRUDE ABOUT 3/8" FROM THE WALL.
STEP 4. MOUNT THE REAR FRAME TO THE WALL BY HOOKING
THE KEYHOLES OVER THE SCREWS. TIGHTEN THE
SCREWS SECURELY.
STEP 5. INSTALL THE REMAINING 2 LAG SCREWS IN THE HOLES
BELOW THE TOP TWO KEYHOLES.
2
MOUNTING KEYHOLES
SCREWS SHOULD
PROTRUDE 3/8"
3/4" PLYWOOD
BACKBOARD
WALL STUDS 16"
ON CENTER
THE REAR FRAME MUST BE SECURED TO WALL USING
ALL 6 LAG SCREWS PROVIDED. THE SCREWS ARE
INTENDED TO GO THROUGH 3/4" PLYWOOD
BACK-BOARD AND THEN INTO WOOD WALL STUDS.
FOR MASONRY SURFACE, THE INSTALLER MUST
PROVIDE APPROPRIATE HARDWARE.
NOTE:
INSTALL 2 LAG SCREWS IN HOLES
BELOW TOP KEYHOLES AFTER THE REAR
FRAME HAS BEEN MOUNTED TO WALL

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO
CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE
OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT
AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.
INSTALLATION
INSTRUCTIONS,
CUBE-IT+ CABINET
IIS-711890, SHEET 3 OF 4 - ASSEMBLY INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS. 6 - CPI/BK
3
MOUNTING CABINET TO REAR PANEL
STEP 1. HOOK THE TOP HINGE PLATE ONTO THE TOP HINGE PIN.
STEP 2. ALIGN THE BOTTOM HINGE PLATE HOLE WITH THE BOTTOM
HINGE PIN. SLIDE THE HINGE PIN DOWN INTO THE HINGE HOLE
AS FAR AS POSSIBLE.
STEP 3. REINSTALL THE CENTER BOLT AND NUT. TIGHTEN ALL THREE
BOTTOM NUTS SECURELY.
THE CENTER BOLT MUST BE REPLACED TO
INSURE THAT THE HINGE PIN DOES NOT
SLIP DURING OPERATION
24.00
36.25,
OR 48.50
24.00,
24.00,
OR 36.00
18.00,

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO
CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE
OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT
AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.
INSTALLATION
INSTRUCTIONS,
CUBE-IT+ CABINET
IIS-711890, SHEET 4 OF 4 - INSTALLATION INSTRUCTIONS, CUBE IT CABINET - 1:5 - 1-28-03 - ISS. 6 - CPI/BK
A
RUBBER GROMMETS (FOUR PROVIDED) CAN
BE INSTALLED IN LARGEST KNOCKOUT HOLE.
SLIT GROOVES WITH KNIFE TO ALLOW CABLE
PASS THROUGH
THE DOOR CAN BE HINGED FROM EITHER SIDE OF THE CABINET.
1. REMOVE THE FOUR SCREWS AND NUTS FROM THE HINGES.
2. TURN THE DOOR OVER.
3. REINSTALL THE SCREWS AND NUTS ON THE OPPOSITE SIDE.
1/2" AND 3/4" CONDUIT KNOCKOUTS
THE 1/2" MUST BE PUNCHED OUT FROM THE INSIDE
THE 3/4" MUST BE PUNCHED OUT FROM THE OUTSIDE
2" AND 2 1/2" CONDUIT KNOCKOUTS
THE 2" MUST BE PUNCHED OUT FROM THE INSIDE
THE 2 1/2" MUST BE PUNCHED OUT FROM THE OUTSIDE DETAIL A
USE COMBINATION OF SLOTS
TO GET DESIRED RAIL DEPTH
MOUNTING EQUIPMENT RAIL
MOUNTING RAIL DEPTH CAN BE ADJUSTED BY
REMOVING NUTS AND MOVING THE RAIL TO
THE DESIRED POSITION. USE A COMBINATION
OF ONE OF THE TWO SLOTS ON THE RAIL AND
ONE OF THE SLOTS ON THE SIDE PANELS.
4