Chauvet Hurricane Haze 2 User manual

User Manual

Hurricane™ Haze 2 User Manual 2 10/1/2010 5:13 PM
CHAUVET®, 2010, All Rights Reserved
Information and specifications in this User Manual are subject to change without notice.
CHAUVET® assumes no responsibility or liability for any errors or inaccuracies that may appear
in this manual.
Author: Anthony Chiappone
Revision: 01
Release Date: 10-01-2010
TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
ACPOWER...........................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 4
FEATURES............................................................................................................................................................................................4
DMXCHANNEL SUMMARY.....................................................................................................................................................................4
PRODUCT OVERVIEW ............................................................................................................................................................................5
3. SETUP............................................................................................................................................................................... 6
FUSE REPLACEMENT.............................................................................................................................................................................6
FIXTURE LINKING ..................................................................................................................................................................................6
DATA CABLING......................................................................................................................................................................................6
DMX Data Cable........................................................................................................................................................... 6
Cable Connectors......................................................................................................................................................... 7
3-Pin to 5-Pin Conversion Chart................................................................................................................................... 7
SETTING UP A DMXSERIAL DATA LINK...................................................................................................................................................7
MOUNTING ...........................................................................................................................................................................................8
Orientation .................................................................................................................................................................... 8
Rigging.......................................................................................................................................................................... 8
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 8
DMXMODE..........................................................................................................................................................................................8
DMXCHANNEL VALUES ........................................................................................................................................................................8
WIRED REMOTE (HH1)(INCLUDED)........................................................................................................................................................9
CONTACT US......................................................................................................................................................................................10
5. APPENDIX....................................................................................................................................................................... 10
DMXPRIMER .....................................................................................................................................................................................10
SETTING THE DMXSTARTING ADDRESS...............................................................................................................................................11
DMX Quick Reference Chart ...................................................................................................................................... 12
GENERAL TROUBLESHOOTING..............................................................................................................................................................13
TECHNICAL SUPPORT..........................................................................................................................................................................13
RETURNS PROCEDURE........................................................................................................................................................................15
CLAIMS ..............................................................................................................................................................................................15
TECHNICAL SPECIFICATIONS ................................................................................................................................................................16

Hurricane™ Haze 2 User Manual 3 10/1/2010 5:13 PM
1.BEFORE YOU BEGIN
What is included
¾1 x Hurricane™ Haze 2
¾1 x Wired Remote (HH1)
¾1 x Power Cord
¾1 x Warranty Card
¾1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the
source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure
that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the voltage rating on your unit matches the line voltage applied. Damage
to your fixture may result if the line voltage applied does not match the voltage
indicated on the rating. All fixtures must be connected to circuits with a suitable
Earth Ground.

Hurricane™ Haze 2 User Manual 4 10/1/2010 5:13 PM
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C).
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
Use only CHAUVET® HFG fluid!
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET® at: 954-929-1115.
2. INTRODUCTION
Features
•2-channel DMX hazer
•Adjustable haze output via DMX, wired remote or control panel on rear
•Adjustable fan speed via DMX, wired remote or control panel on rear
Additional Features
•True continuous output
•Variable output angle
•Low fluid indicator
•Wired multi-function remote included
•Water-based hazer
DMX Channel Summary
C HANNEL F UNCTION
1
Haze output
2
Blower/fan speed
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.

Hurricane™ Haze 2 User Manual 5 10/1/2010 5:13 PM
Product Overview
Remote
control
DIP switches
DMX
LED
“Heating”
LED
Power
switch
No fluid LED
in
d
i
cato
r
DMX out
DMX in
Fuse holder
Power
input
Back door handle
for fluid container
& remote control
storage
Use only
CHAUVET® HFG

Hurricane™ Haze 2 User Manual 6 10/1/2010 5:13 PM
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
3.SETUP
Fuse Replacement
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To
comply with the EIA-485 standard no more than 32 fixtures should be
connected on one data link. Connecting more than 32 fixtures on one serial
data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
Type: shielded, 2-conductor twisted pair
Maximum capacitance between conductors: 30 pF/ft
Maximum capacitance between conductor and shield: 55 pF/ft
Maximum resistance: 20 ohms/1000 ft
Nominal impedance: 100 – 140 ohms
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.

Hurricane™ Haze 2 User Manual 7 10/1/2010 5:13 PM
This drawing provides
a general illustration of
the DMX Input/Output
panel of a lighting
fixture.
Universal DMX Controller
Continue the link
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
CAUTION Do not allow contact between the common and the fixture’s chassis ground.
Grounding the common can cause a ground loop, and your fixture may
perform erratically. Test cables with an ohmmeter to verify correct polarity and
to make sure the pins are not grounded or shorted to the shield or each other.
3-Pin to 5-Pin Conversion Chart
Note! If you use a controller with a 5-pin DMX output connector, you will need to use
a 5-pin to 3-pin adapter.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART
Conductor 3-Pin Female (Output) 5-Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Not used Pin 4
Not used Pin 5
Setting up a DMX Serial Data Link
1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female)
3-pin connector to the input connector of
the next fixture consisting of a (male) 3-pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CO
MM
O
N
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) on
the output of the
last fixture.
DMX connector configuration
To avoid signal transmission
problems and interference, it is
always advisable to connect a
DMX signal terminator.

Hurricane™ Haze 2 User Manual 8 10/1/2010 5:13 PM
Hanging Clamp
Note!
Clamp is sold separatel
y
.
Mounting
Orientation
This fixture may be mounted in a hanging or sitting position, provided there is adequate room for
ventilation.
Rigging
It is important never to obstruct the vents pathway. Mount the fixture using,
a suitable “C” or “O” type clamp.
•When selecting installation location, take into consideration fluid
replacement, access, and routine maintenance.
•Safety cables must always be used.
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
4. OPERATING INSTRUCTIONS
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the “DMX Primer section” in the Appendix of this manual.
1) This fixture will automatically switch to DMX mode, once a DMX controller has been plugged into
the 3-pin DMX input.
2) Use DIP switches 1~9 to set the DMX address.
DMX Channel Values
CHANNEL VALUE FUNCTION
1
000 Ù255 Haze output 0% Ù100%
2
000 Ù255 Blower/fan speed 0% Ù100%

Hurricane™ Haze 2 User Manual 9 10/1/2010 5:13 PM
Wired Remote (HH1) (Included)
This is the controller that comes with the Hurricane™ Haze 2. There are three functions of this remote. Please
see the below instructions for details on each of these operations.
Timer Function
1) Plug in the haze machine to power and turn the power switch to the fixture on.
2) Plug in the timer remote to the Manual Controller socket on the rear of the haze machine.
3) Press the <TIMER ON/OFF> button on the timer remote. The LED above the button should light, indicating
activation of function.
4) You may now set the INTERVAL & DURATION adjustment knobs to the desired position.
Note: The< INTERVAL> is the time in between bursts of haze.
Note: The <DURATION> is the time that the haze machine will run during the burst.
Manual Function
1. Press the <MANUAL> button, and the haze machine will output haze for as long as you hold down the button,
at full blower speed and 100% output.
Continuous Function
1. Press <CONTINUOUS>.
2. Adjust the <OUTPUT ADJUSTMENT KNOB> to desired position.
Note: The <INTERVAL> and <DURATION ADJUSTMENT> knobs will have no effect while the
CONTINUOUS function is activated.
Note: The blower fan remains at full and the <OUTPUT ADJUSTMENT> knob controls the haze
output.
Continuous LED
Duration adjustment
Interval adjustment
Output
adjustment
Timer active LED
Timer on/off
button
Manual/ready
LED
Manual button
Continuous
button

Hurricane™ Haze 2 User Manual 10 10/1/2010 5:13 PM
Contact Us
World Wide
General Information CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
5.APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).

Hurricane™ Haze 2 User Manual 11 10/1/2010 5:13 PM
Setting the DMX Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address"
from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses 6 DMX channels and was addressed to start on
DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start addresses
so that the channels used do not overlap, and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX-512 control protocol, we suggest jumping to the
Appendix Section and reading the heading “DMX Primer section”. It contains very useful information that will
help you understand its use.
Set the start address using the group of DIP switches located usually on bottom of the fixture. Each DIP switch
has an associated value. Adding the value of each switch in the ON position will provide the start address.
Figuring out which switches to toggle ON given a specific start address can be accomplished by determining
which switch values will add up to the address value, and turning these switches on. Do so by doing the
following:
1) Determine the largest value switch that is less than the start address. Turn this switch on.
2) Subtract the value of the DIP switch you just turned on from the starting address number.
3) Determine the largest value switch that is less than the remainder from the previous subtraction. Turn this
switch on.
4) Subtract the value of the switch you just turned on from the remainder of the previous subtraction.
5) Repeat steps three and four until you have a remainder of zero.
EXAMPLE STARTING ADDRESS
Address 10
Switch # 4 = 8
Switch # 2 = 2
Total = 10
Address 26
Switch # 5 = 16
Switch # 4 = 8
Switch # 2 = 2
Total = 26
Resolving address
using simple math.
Address 233
233 – (128) = 105, Turn ON DIP # 8
105 – (64) = 41, Turn ON DIP # 7
41 – (32) = 9, Turn ON DIP # 6
9 – (8) = 1, Turn ON DIP # 4
1 – (1) = 0, Turn ON DIP # 1
DIP SWITCH (DMX
V
ALUE)
1
2
3
4
5
6
7
8
9
1
2
4
8
16
32
64
128
256
13456789 ON
OFF
1 2 4 8
16 32 64
128 256
13456789 ON
OFF
1 2 4 8
16 32 64
128 256
13456789 ON
OFF
1 2 4 8
16 32 64
128 256
13456789 ON
OFF
1 2 4 8
16 32 64
128 256
13456789 ON
OFF
1 2 4 8
16 32 64
128 256
12222223456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256
123456789 ON
OFF
1 2 4 8
16 32 64
128 256

Hurricane™ Haze 2 User Manual 12 10/1/2010 5:13 PM
DMX Quick Reference Chart
DMX Address Quick Reference Chart
DIP Switch Position
DMX DIP
SWITCH SET #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
1=ON #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
X=OFF or ON #6 0 1 0 1 0 1 0 1 0 1 01 0 1 0 1
#1 #2 #3 #4 #5
0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481
0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
1 1 0 0 0 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483
0 0 1 0 0 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484
1 0 1 0 0 5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485
0 1 1 0 0 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486
1 1 1 0 0 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487
0 0 0 1 0 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488
1 0 0 1 0 9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489
0 1 0 1 0 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490
1 1 0 1 0 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491
0 0 1 1 0 12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492
1 0 1 1 0 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493
0 1 1 1 0 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494
1 1 1 1 0 15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495
0 0 0 0 1 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496
1 0 0 0 1 17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497
0 1 0 0 1 18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498
1 1 0 0 1 19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499
0 0 1 0 1 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500
1 0 1 0 1 21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501
0 1 1 0 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502
1 1 1 0 1 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503
0 0 0 1 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504
1 0 0 1 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505
0 1 0 1 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506
1 1 0 1 1 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507
0 0 1 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508
1 0 1 1 1 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509
0 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510
1 1 1 1 1 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511
DIP Switch Position DMX Address

Hurricane™ Haze 2 User Manual 13 10/1/2010 5:13 PM
General Troubleshooting
Symptom Solution(s)
Auto shut off Check thermal switch reset
Breaker/Fuse keeps
blowing Check total load placed on device
Device has no power Check for power on Mains.
Check device’s fuse. (internal and/or external)
Fixture is not responding Check DMX Dip switch settings for correct addressing Check DMX cables
Check polarity switch settings
Fixture is on but there is
no movement to the audio
Make sure you have the correct audio mode on the control switches. If
audio provided via ¼” jack, make sure a live audio signal exists
Adjust sound sensitivity knob
Loss of signal Use only DMX cables Install terminator
Note: Keep DMX cables separated from power cables or black lights.
Remote does not work Make sure connector is firmly connected to device
Stand alone mode All CHAUVET® lighting fixtures featuring stand-alone functions do not require additional settings, simply power the fixture and it will
automatically enter into this mode
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support at the location below.
Technical Support
Address: Service Dept.
5200 NW 108th Ave
Sunrise, FL 33351
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com

Hurricane™ Haze 2 User Manual 14 10/1/2010 5:13 PM
Warning!
This Haze Machine must only be used with CHAUVET® HFG Haze Fluid!
Failure to use the proper fluid with this product may cause damage to the product and may also
void the CHAUVET® warranty.
All haze machines are prone to clogging due to the thick consistency of the fog liquid and the high
temperature at which it vaporizes. However, a properly maintained fog machine should provide
years of reliable use. Cleaning your fog machine regularly will help reduce costly replacement and
repair charges.
Maintenance
Do not allow the haze machine to become contaminated. After every 40 hours of continuous operation, it is
recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the
system to prevent the accumulation of particulate matter in the heating element.
The recommended cleaning procedure is as follows:
1. Empty all fog liquid from the machine. Add cleaning solution to tank. Plug unit in and begin warm
up.
2. Run the unit in a well-ventilated area until the tank is almost empty. Do not allow the pump to run
dry.
3. Replace nozzle.
4. Cleaning is now complete. Refill with fog liquid. Run the machine for 30-60 seconds, or until all
fluid has been removed from the system.
Storage
When storing the machine, run distilled water (not tap water) through the system as described in the cleaning
regiment above. This will help avoid any particles condensing inside the pump or heater. Then, empty the fluid
reservoir. Run the machine for 30-60 seconds, or until all fluid has been removed from the system.
It is required to test-run the machine on a monthly basis in order to achieve its best hazing
condition. After testing, be sure to clean and drain the system prior to storing.
Never store the machine with fluid in the lines.
Never place the hazer on any flammable material (i.e. carpet, fabric etc.) during operation. All
fog/hazer machines should always be on a non-flammable surface, such as concrete or tile.
All haze machines are capable of setting off smoke detectors, as they may detect the water-based
particles as smoke. Never disable a smoke detector.

Hurricane™ Haze 2 User Manual 15 10/1/2010 5:13 PM
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from
inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is
always a safe method to use.
Note: If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

Hurricane™ Haze 2 User Manual 16 10/1/2010 5:13 PM
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 11.1 in (284 mm)
Width ............................................................................................................................ 10.5 in (267 mm)
Height.............................................................................................................................. 14 in (360 mm)
Weight ............................................................................................................................18.7 lbs (8.5 kg)
POWER
Voltage-specific power input ...........................................................115 VAC, 60 Hz or 230 VAC, 50 Hz
Power Consumption@ 120 V......................................................................................504 W, 4.1 A max
Inrush Current@ 120 V ................................................................................................................... 4.1 A
Power Factor@ 120 V.......................................................................................................................0.98
OUTPUT/FLUID CONSUMPTION
Output.......................................................................................................................................1,200 cfm
Fluid consumption ....................................................................................................................21 ml/min
FUSE
115 VAC.............................................................................................................F 5 A, 250 V (fast blow)
230 VAC.............................................................................................................F 3 A, 250 V (fast blow)
COMPATIBLE FLUID
Haze Fluid .................................................................................................................. CHAUVET® HFG
INDOOR/OUTDOOR
Rating........................................................................................................................For indoor use only
THERMAL
Maximum ambient temperature.........................................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input................................................................................................locking 3-pin XLR male socket
Data output...........................................................................................locking 3-pin XLR female socket
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................DMX-512 USITT
DMX Channels .......................................................................................................................................2
ORDERING INFORMATION
Hurricane™ Haze 2.................................................................................................HURRICANEHAZE2
Haze Fluid (gallon) ...........................................................................................................................HFG
WARRANTY INFORMATION
Warranty..............................................................................................................1-year limited warranty