Chesapeake & midlantic Bmt-75wa User manual

Page 1of 2

Figure 1 - BMT-75WA Exploded View with BDH-7500 Shown

INSTALLATION MANUAL –BMT-75WA

Wall Arm Mount Accessory for BDH-7500

WARNING: Before beginning installation of this product, carefully review

the safeguards and precautions found on page 2 of this manual.

Unpacking

Unpack carefully. This is mechanical equipment and should

be handled with care. If an item appears to have been

damaged in shipment, replace it properly in its carton and

notify the shipper. If any items are missing, notify the

shipper. The shipping carton is the safest container in which

the unit may be transported. Save it for possible future use.

Service

If the unit ever needs repair service, the customer should

contact Chesapeake & Midlantic Marketing for a return

materials authorization (RMA) and shipping instructions.

Care and Maintenance

Perform routine maintenance to keep the unit dust free.

Model Designation

BMT-75WA WALL ARM MOUNT w/ ADAPTER PLATE for

BDH-7500

Description

The BMT-75WA accessory enables the BDH-7500 to be

installed on a wall. The wall mount is constructed of powder

coated aluminum with stainless steel fasteners.

Hardware Kit

4 x Lock Nut, ¼-20

4 x Washer, ¼” Rubber Bonded

Tools Required

7/16”Socket & Driver

RTV Sealant

Certification

Installation should be performed by a licensed professional

and conform to the National Electrical Code (NEC) and any

applicable local codes.

Installation

1. Remove unit from packaging.

2. Hold wall mount up to installation surface and use as a

template to mark the hole pattern. Drill out installation

surface with appropriate sized drill bit for fasteners and

anchors being used.

3. Run network cable to installation site leaving enough

slack at the end of the pole to allow cable entry through

the mount and housing to the camera.

4. Attach mount to installation surface using customer-

supplied fasteners (max 1/4" diameter). Each fastener

should have a minimum 200 lbs pull-out strength.

5. Apply a bead of RTV sealant to the edge of the adapter

plate on the bottom surface.

6. Prepare BDH-7500 housing per instructions included with

the unit treating BMT-75WA as the installation surface.

7. Attach housing to conduit base using the rubber washers

and ¼-20 nuts from the kit. Ensure the rubber side of

the washer faces the base.

Mount and

adapter plate are

pre-assembled.

Page 2of 2

IMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating instructions should be read before the unit is operated.

2. Retain Instructions - The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Cleaning - Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury to a person and serious

damage to the unit. Use only with a stand, tripod, bracket, or mount recommended by the manufacturer or sold with the product. Any mounting of the

unit should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

8. Ventilation - Openings in the enclosure, if any, are provided for ventilation, to ensure reliable operation of the unit, and to protect it from overheating.

These openings must not be blocked or covered. This unit

should not be placed in a built-in installation unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

9. Power Sources - This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power

supply you plan to use, consult your appliance dealer or local power company. For units intended to operate from battery power or other sources, refer

to the operating instructions.

10. Grounding or Polarization - This unit may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This

plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If

the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

Alternatively, this unit may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-

type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do

not defeat the safety purpose of the grounding-type plug.

11. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against

them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

12. Power Lines - An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall

into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines or circuits as

contact with them might be fatal. U.S.A. models only - refer to the National Electrical Code Article 820 regarding installation of CATV systems.

13. Overloading - Do not overload outlets and extension cords as this can result in a fire or electric shock.

14. Object and Liquid Entry - Never push objects of any kind into this unit through openings, as they may touch dangerous voltage points or short out parts

that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

15. Servicing - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

16. Damage Requiring Service - Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions,

as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to

its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f. When the unit exhibits a distinct change in performance--this indicates a need for service.

17. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or

have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

18. Safety Check - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in

proper operating condition.

19. Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. U.S.A. models only--Section 810 of the

National Electrical Code, ANSI/NFPA No.70-1981, provides information with respect to proper grounding of the mount and supporting structure,

grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit,connection to grounding electrodes, and requirements

for the grounding electrode.

20. Lightning - For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from

the wall outlet and disconnect the cable system. This will prevent damage to the unit due to lightning and power line surges.

FCC NOTICE

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's

instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing

device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Relocate the monitor away from the TV/radio receiver.