Chicago Electric 91482 User manual

10”TILE SAW
24” DEEP CUT - 2.5 HP
Model 91482
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at: http://www.harborfreight.com
Copyright 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
®
©

SKU 91482 For technical questions, please call 1-800-444-3353. Page 2
PRODUCT SPECIFICATIONS
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 18
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
Item Description
Electrical Requirements 120 V / 60 Hz / 1800 W / Single Phase
20 AMP Circuit Breaker
15 Amps
3-Prong, Grounded Power Cord Plug
Motor 2.5 HP / 3,450 RPM
Blade Speed 3,400 RPM
Product Compatibility For use with SKU 91483 Stand (not included).
Cutting Capacity 24” Rip Length / 16” Diagonal / 3-3/4” Maximum Depth
Saw Blade (not included)
Requirements 10” Continuous Rim, Diamond w/ 5/8” Round Arbor Hole *Must Be Rated At 3,500 RPM Or Greater.
Drive Type Belt Drive / Size A660.
Angle Cutting Capacity 45° Left & Right Miter Block / 45° Right Bevel Block.
Water Pump Capacity 3.17 Gallons Per Minute.
Overall Dimensions 41” L x 21” W x 20-1/2” H.
Weight 113 Pounds.
E221466
REV 04/05

SKU 91482 For technical questions, please call 1-800-444-3353. Page 3
3. Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tool should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
2. Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
3. Do not expose unprotected areas to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
4. Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immedi-
ately. Damaged Power Cords increase the risk of electric shock.
5. When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
1. Stay alert. Watch what you are doing, and use common sense when oper-
ating a power tool. Do not use a power tool while tired or under the influ-
ence of drugs, alcohol, or medication. A moment of inattention while operat-
ing power tools may result in serious personal injury.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
WORK AREA
1. Keep your work area clean and well lit. Cluttered and dark work areas
invite accidents.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 4
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
4. Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
6. Use safety equipment. Always wear eye protection. Non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
1. Use clamps (not included) or other practical ways to secure and support
a smaller workpiece to the MainTable (99). Holding the work by hand or
against your body is unstable and may lead to loss of control.
2. Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
3. Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
4. Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
6. Maintain tools with care. Keep tools clean. Properly maintained tools are
easier to control. Do not use a damaged tool. Tag damaged tools “Do not use”
until repaired.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 5
7. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly main-
tained tools.
8. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
1. Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of
electric shock. (See Figure A, next page.)

SKU 91482 For technical questions, please call 1-800-444-3353. Page 6
2. The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
3. Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like that in the following illustration. (See Figure A.)
FIGURE A
3-PRONG PLUG
ELECTRICAL OUTLET
EXTENSION CORDS
1. Grounded tools require a three wire extension cord.
2. As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure B, next page.)
3. The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure B.)
4. When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required.
(See Figure B.)
5. If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure B.)

SKU 91482 For technical questions, please call 1-800-444-3353. Page 7
FIGURE B
6. If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
7. Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it. Protect your extension cords from sharp objects,
excessive heat, and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS
*
(120 VOLT)
NAMEPLATE
AMPERES
(
At Full Load
)
EXTENSION CORD LENGTH
25
Feet 50 Feet 75 Feet 100 Feet 150 Feet
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
* Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.
V ~
A
no
xxxx/min. No Load Revolutions per Minute (RPM)
Amperes
Volts Alternating Current
Underwriters
Laboratories, Inc.
Canadian Standards
Association
Double Insulated
SYMBOLOGY
FIGURE C

SKU 91482 For technical questions, please call 1-800-444-3353. Page 8
1. Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use the Tile Saw in
areas near flammable chemicals, dusts, and vapors.
2. Maintain labels and nameplates on theTile Saw. These carry important infor-
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.
3. Use the right product for the right job. There are certain applications for which
this product was designed. Do not use small equipment, tools, or attachments to
do the work of larger industrial equipment, tools, or attachments. Do not use this
product for a purpose for which it was not intended.
4. This product must continuously run with cold water. Dry running will cause
serious damage to the Pump seals.
5. CAUTION! Keeps hands and fingers away from cutting area and Saw
Blade. Use an appropriate “push stick” (not included) when necessary.
6. Check Blade Guard for proper upward/downward movement before each
use. Do not operate the Tile Saw if the Blade Guard does not move freely. Never
clamp or tie the Blade Guard into the upper position. If the Tile Saw is accidently
dropped the Blade Guard may be bent. Raise the Blade Guard and make sure it
moves freely and does not touch the Saw Blade or any other part of the Saw, in
all angles and depths of cut.
7. Do not pull or carry theTile Saw by its Power Cord or pull the Cord around
sharp corners or edges. Do not unplug the Tile Saw by pulling on the Cord.
Keep the Cord away from heated surfaces.
8. Keep all guards in place and in proper working order.
9. Do not handle the Power Switch with wet hands.
10. Make sure theTile Saw is mounted on a flat, level, sturdy work surface
capable of supporting the weight of the Saw and workpieces.
11. Always use Continuous Rim, Diamond Saw Blades with a 10”diameter, 5/8”
round arbor hole, and rated at 3,500 RPM or greater. Saw Blades that do not
match the mounting hardware of theTile Saw or that are rated less than the
required minimum RPM will run eccentrically causing loss of control or may fly off
the Saw.
12. Use theTile Saw only for cutting ceramic tile, quarry tile, marble, terra cotta,
and slate with a maximum thickness of 3”.
SPECIFIC SAFETY RULES

SKU 91482 For technical questions, please call 1-800-444-3353. Page 9
13. Do not use theTile Saw for cutting metals or for cutting curves. This may
cause the Saw Blade to break and/or reduce its service life.
14. Make sure the Saw Blade is wet at all times when cutting.
15. Keep all electrical connections dry and off the ground.
16. Use cold water only. Never use hot water. Using hot water can damage the
Pump seals.
17. Never run theTile Saw without a water supply. Running the unit without a
water supply will cause irreparable damage to the Pump, Motor, or Blade.
18. Make sure the water supply used for theTile Saw is not dirty, sandy, and
does not contain any corrosive chemical products. Always add fresh, clean
water before using the unit.
19. Never leave theTile Saw unattended when it is plugged into an electrical
outlet. Turn off the Tile Saw, and unplug it from its electrical outlet after use.
20. Always keep the water level at the recommended level. Fill the Tank with
enough water so that the Pump’s inlet is completely submerged, but not so much
water that the Tank overflows.
21. Never splash water on the Motor, Power Switch, Power Cord, or any other
electrical component. Make sure to stand on a dry, insulated surface such as a
rubber mat while using the Tile Saw.
22. Make sure to clean theTank thoroughly after each use.
23. To avoid accidental injury, always wear heavy duty work gloves when
changing the Saw Blade.
24. Before using theTile Saw, make sure the Saw Blade is properly mounted
on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked
or bent.
25. The Saw Blade may become hot while cutting. Allow the Saw Blade to com-
pletely cool before handling.
26. Allow the Saw Blade to spin up to full speed before feeding a workpiece
into it. When turning off the Tile Saw, allow the Saw Blade to spin down and
stop on its own. Do not press against the Saw Blade to stop it.
27. Do not force the workpiece into the Saw Blade when cutting. Apply moder-
ate pressure, allowing the Saw Blade to cut without being forced.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 10
28. Turn off theTile Saw and allow the Saw Blade to stop on its own if the Saw
Blade is to be backed out of an uncompleted cut.
29. Never attempt to remove material stuck in theTile Saw while it is plugged
in or running.
30. When cutting a large workpiece make sure its entire length is properly
supported.
31. Never stand on theTile Saw. Serious injury can result if the Tile Saw is tipped
or if the rotating Saw Blade is accidently contacted.
32. Industrial applications must follow OSHA requirements.
33. For your safety: In extreme working conditions the Circuit Breaker will auto-
matically switch off the Motor to prevent overheating. In this event, turn the
Power Switch to its “OFF” position. Wait five minutes or until the Motor has
cooled. Depress the Circuit Breaker. Then, turn the Power Switch to its “ON”
position to resume cutting. If the Circuit Breaker continues to trip, have the tool
serviced by a qualified technician.
NEVER attempt to disable the Circuit Breaker.
34. Always turn off theTile Saw, unplug it from its electrical outlet, and allow it
to stop before changing accessories or performing any inspection, mainte-
nance, or cleaning procedures.
35. WARNING! Some dust created by power sanding, sawing, grinding, drill
ing, and other construction activities, contain chemicals known (to the State of
California) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are: lead from lead-based paints, crystalline silica
from bricks and cement and other masonry products, arsenic and chromium from
chemically treated lumber. Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your exposure to these chemicals:
work in well ventilated areas, and work with approved safety equipment such as
those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq.)
36. WARNING! People with pacemakers should consult their physician(s)
before using this product. Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference or failure of the pacemaker.
37. WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 11
ALUMINUM
BASE
(38)
ALUMINUM
COLUMN
(35)
BOLT (30)
LARGE WASHER (32)
BOLT (59)
WASHER (58)
POSITIONTUBE
(57)
SHAFT
(36)
REARVIEW
FIGURE D
KNOB
(31)
ASSEMBLY INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer to the
Assembly Diagram on page 19.
1. WARNING! Always make sure the Power Switch of the Tile Saw is in its “OFF”
position and the unit is unplugged from its electrical outlet prior to assembling the unit,
adding any accessories, or making any adjustments to the unit.
2. Mount theTile Saw to the machine frame by connecting the Aluminum Base (38) to the
AluminumColumn(35), usingtheShaft (36),PositionTube(57), Bolt(30), LargeWasher
(32), Bolt (59), and Washer (58). (See Figure D.)
3. Tighten the Knob (31) to hold the Tile Saw in position. (See Figure D.)
4. At this time remove the Bolts (76) that hold the Pulley Cover (75) on, remove the Cover,
and check that the Belt (74) is tight and in good condition. It should deflect (move) a
little (about 1/2” deflection) when pressed with the thumb.
If the Belt is loose, do the following:
a. Loosen all 4 Nuts (46) that hold down the Motor (45).
b. Gradually tighten the Belt Tension Bolt (41), all the while checking the tension on
the Belt - see Figure D. Tighten the Belt to about 1/2” deflection. Do not over-
tighten; overtightening can cause damage to the bearings in the Motor.
c. Retighten all 4 Nuts (46).
d. Reinstall the Pulley Cover (75) using the Bolts (76).
5. Slide the Water Tank (3) through the slot in the Machine Frame (11) and under the
Aluminum Bar (83), so that the entire Water Tank rests inside the Machine Frame.
(See Figure E, next page.)
BELTTENSION
BOLT (41)

SKU 91482 For technical questions, please call 1-800-444-3353. Page 12
WATER TANK
(3) MACHINE
FRAME
(11)
FIGURE E
BOLT
(93)
EXTENSION
TABLE
(94)
MAINTABLE
(99)
FIGURE G
FIGURE F
ELECTRICAL RECEPTACLE
PUMP
(105)
PUMP POWER CORD
WATER HOSE
(PRE-ATTACHED)
(PLACE PUMP IN REAR
OF WATER TANK)
6. Plug the Power Cord of the Pump (105) into the electrical receptacle located on the
back of the Motor. Then, set the Pump (105) in the rear of theWaterTank (3), using the
four suction feet on the bottom of the Pump. (See Figure F.)
7. Attach the Extension Table (94) to the Main Table (99), using the four Bolts (93).
(See Figure G.)
8. If desired, this saw can be mounted to a Stand (ITEM 91483, not included). See the
manual included with the stand for installation instructions.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 13
CHANGING OR INSTALLING A SAW BLADE
1. WARNING! Always make sure the Power Switch of the Tile Saw is in its “OFF”
position and the unit is unplugged from its electrical outlet prior to assembling the
unit, adding any accessories, or making any adjustments to the unit.
2. Loosen the Knob (53) located on the side of the Blade Guard (60) and raise the
Blade Guard. (See Figure H.) Then, retighten the Knob to lock the Blade Guard in
the “up” position.
FIGURE H
BLADE GUARD
(60)
KNOB
(53)
(DOWN POSITION)
3. Depress the Brake Shaft (68) while turning the Saw Blade (65) (or Spindle (80) if you
have not yet installed a Saw Blade) until the Brake Shaft (68) depresses fully. This
will prevent the Spindle from spinning.
(See Figure I, next page.)
4. Using the accessory Wrench, unscrew the Nut (67) counterclockwise and remove it
and the Outer Flange (66). (See Figure J, next page.)
5. Using heavy duty gloves to avoid accidental cuts, remove the old Saw Blade (65) and
install a new Saw Blade. Always use Continuous Rim, Diamond Saw Blades
with a 10”diameter, 5/8”round arbor hole,and rated at 3,500 RPM or greater.
(See Figure K, next page.)
6. NOTE: When installing a Saw Blade (65), make sure the“ARROW” depicted on
the upper side of the Saw Blade points to the front of the Tile Saw.
(See Figure K.)

SKU 91482 For technical questions, please call 1-800-444-3353. Page 14
FIGURE I
BRAKE SHAFT
(68)
FIGURE K
SAW
BLADE
(65)
FIGURE L KNOB
(53)
BLADE
GUARD
(60)
FIGURE J
NUT
(67)
OUTER
FLANGE
(66)
WRENCH
7. Refasten the Outer Flange (66) and Nut (67). Make sure to tighten the Nut fully
before using the Tile Saw. (See Figure J.)
8. Loosen the Knob (53). Lower the Blade Guard (60) fully. Then, retighten the Knob to
lock the Blade Guard in position. (See Figure L.)]
ROTATION
ARROW

SKU 91482 For technical questions, please call 1-800-444-3353. Page 15
OPERATING INSTRUCTIONS
1. Place the Saw (or saw and stand, if the optional stand is installed) on a level, even
surface, capable of supporting the tool and any forces exerted during work. Fill the
Water Tank (3) with enough cold water so that the Pump (105) is completely sub-
merged, but not so much water that the Water Tank overflows.
NOTE: To prevent excessive wear on the Saw Blade (65), make sure to maintain a
continuous flow of water over the entire Saw Blade while cutting. Never cut anything
if the water flow is not continuous.
2. To attach the Parallel Guide (84), loosen the Knob (86) on the side of the Guide.
Place the hooked portion of the Guide over the upturned edge of the Main Table (99).
Slide the Guide horizontally to the right or left until the desired width of cut is ob-
tained (allowing space for grout). Then, tighten the Knob to lock the Guide in posi-
tion. (See Figure M.)
FIGURE M
KNOB
(86)
PARALLEL
GUIDE
(84)
MAIN
TABLE
(99)
3. Attach the Angle Block (85) as you did the Parallel Guide, using the two Knobs (86)
on the side of the Guide. Use the cutting groove in the middle of the MainTable to
brace the edge of the tile as the tile is slid underneath the Saw Blade (65).
(See Figure N.)
ANGLE BLOCK
(85)
KNOB
(86)
FIGURE N

SKU 91482 For technical questions, please call 1-800-444-3353. Page 16
4. Attach the 45° Miter Block (108) as you did the Parallel Guide, using the Knob (86)
on the side of the Guide. (See Figure O.)
FIGURE O
45° MITER
BLOCK
(108)
KNOB
(86)
5. Plug the Power Cord of the Tile Saw into the nearest, 120 volt, grounded, electrical
outlet.
6. Make sure to wear an ANSI approved safety impact full face shield over ANSI
approved safety glasses and a dust mask when cutting tile. At all times, keep
hands and fingers away from the spinning Saw Blade (65).
7. Place the marked tile on the Main Table (99) and brace it against the Guide you have
chosen to use. Then, align the cut mark with the Saw Blade (65).
8. Turn the Flow Control Lever (105D) all the way down.Turn the Power Switch to its
“ON” position, and allow the Saw Blade (65) to spin up to full speed. Adjust the Flow
Control on the Pump until the water reaches the edge of the Blade just before the
Blade would contact the material being cut. Make sure the Pump (105) is supplying
a continuous flow of water to the entire Saw Blade. (See Figure O.)
9. Make sure the Blade Guard (60) is in place and in proper working order. Hold the tile
firmly against the Guide with one hand. With the other hand, move the Main Table
(99) and tile slowly underneath the Saw Blade (65).
10. Continue moving the MainTable (99) and tile underneath the Saw Blade (65) until
the cut is completed.
11. Once the cut is completed turn the Power Switch to its “OFF” position, and allow the
Saw Blade (65) to stop on its own. Then remove the cut tile and debris from the
Main Table (99), and unplug the Power Cord from the electrical outlet.
12. NOTE: If the Motor (45) stops suddenly while cutting, turn the Power Switch to
its “OFF” position. Wait approximately 5 minutes. Then reset the Circuit Breaker
to resume cutting. (See Figure O.)
POWER SWITCH CIRCUIT BREAKER

SKU 91482 For technical questions, please call 1-800-444-3353. Page 17
INSPECTION, MAINTENANCE, AND CLEANING
1. WARNING! Make sure the Power Switch of the Tile Saw is in its “OFF” position
and that the unit is unplugged from its electrical outlet before performing any inspec-
tion, maintenance, or cleaning procedures.
2. Before each use, inspectthegeneral conditionof theTile Saw. Checkforloosescrews,
misalignment or binding of moving parts, damaged electrical wiring, damaged Hose,
and any other condition that may affect its safe operation. If abnormal noise or vibra-
tion occurs, have the problem corrected before further use. Do not use damaged
equipment.
3. Before each use, inspect the Diamond Saw Blade. Using a dull Saw Blade will cause
excessive wear on the Motor, and will not produce a satisfactory cut. Replace with a
new Saw Blade when needed.
4. Before each use,inspect the mounting Screws on all Safety Covers and the Arbor Nut
on the Saw Blade Shaft. If necessary, retighten all loose Screws and Nuts.
5. NOTE: The Pump is non-serviceable. If the Pump should fail, first try clearing the
intake of debris and make sure the hole is not plugged. If the Pump still does not
operate properly, it must be replaced.
6. To clean the exterior parts: Use only a clean cloth and mild detergent to clean the
body of the Tile Saw. Do not use solvents. Do not immerse any electrical part of the
tool in liquid.
7. When storing, always completely empty the Tile Saw of water. Frost will damage the
Pump if the unit contains water. Store the Tile Saw indoors in a dry, frost-free room.
8. Periodically, remove the Pulley Cover (75) as explained under Assembly Instruc-
tion 4 on page 11 and check the condition and tightness of the Belt (74). If the belt
appears damaged (frayed, cracked, or partially broken) or is broken, loosening the 4
Nuts (46) and the Belt Tension Bolt (41), replace the Belt (74) and retighten it as ex-
plained on page 11.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT, ORTHAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSEDTECHNICIANS,AND NOT BYTHE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE-
MENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.

SKU 91482 For technical questions, please call 1-800-444-3353. Page 18
PARTS LIST
Part # Description Qty. Part # Description Qty.
1 Washer 4 61 Screw 3
2 Nut 2 62 Rubber Pad 1
3 Water Tank 1 63 Bearing 2
4 Elastic Washer 4 64 Inner Flange 1
5 Bolt 2 65 Saw Blade (not included) 1
6 Rubber Insert 1 66 Outer Flange 1
7 Aluminum Guide 1 67 Nut 1
8 Plastic Insert 2 68 Brake Shaft 1
9 Pressing Plate 2 69 Screw 2
10 Screw 4 70 Brake Holder 1
11 Machine Frame 1 71 Retaining Ring 1
12 Nut 4 72 Spring 1
13 Bolt 2 73 Washer 3
14 Bolt 2 74 Belt 1
15 Elastic Washer 2 75 Pulley Cover 1
16 Washer 2 76 Bolt 2
17 Adjusting Plate 2 77 Position Plate 1
18 Carrying Handle 2 78 Bolt 3
27 Plastic Insert 1 79 Spindle Pulley 1
28 Bolt 2 80 Spindle 1
29 Bolt 1 81 Spindle Sleeve 1
30 Bolt 1 82 Sliding Guide 1
31 Knob 1 83 Aluminum Bar 1
32 Large Washer 1 84 Parallel Guide 1
33 Position Tube 1 85 Angle Block 1
34 Washer 1 86 Knob 4
35 Aluminum Column 1 87 Bolt 1
36 Shaft 1 88 Rolling Wheel 1
37 Coach Bolt 4 89 Bolt 1
38 Aluminum Base 1 90 Steel Plate 1
39 Motor Adjusting Bar 1 91 Front Table 1
40 Large Washer 1 92 Bolt 2
41 Belt Tension Bolt 1 93 Bolt 4
42 Motor Pulley 2 94 Extension Table 1
43 Screw 2 95 Nut 2
44 Key 2 96 Bolt 2
45 Motor 1 97 Elastic Washer 2
46 Nut 4 98 Washer 2
47 Elastic Washer 4 99 Main Table 1
48 Washer 4 100 Linear Bearing 2
49 Screw 1 101 Retaining Ring 2
50 Three-Way Tube 1 102 Steel Insert 2
51 Rubber Plate 1 103 Nylon Insert 2
52 Washer 1 104 Sliding Tube 1
53 Knob 1 105 Pump 1
54 Screw 1 105A Pump Body 1
55 Connecting Plate 1 105B Impeller 1
56 Small Shaft 1 105C Cover 1
57 Position Tube 1 105D Flow Control Lever 1
58 Washer 1 106 Rubber Pad 1
59 Bolt 1 107 Water Supply System 1
60 Blade Guard 1 108 45° Miter Block 1

SKU 91482 For technical questions, please call 1-800-444-3353. Page 19
ASSEMBLY DIAGRAM
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
105A
105B
105C
105D