Optimum OPTisaw CS 275 User manual

Operating manual
Version 1.1.3
Circular metal saw
Img.0-1: Circular metal saw CS315

Version 1.1.3 - 2020-07-302 Translation of original operating manual
CS275 | CS315
EN
CS275_CS315_GBIVZ.fm
Table of contents
1 Safety
1.1 Safety instructions (warning notes)...........................................................................................................6
1.1.1 Classification of hazards...........................................................................................................................6
1.1.2 Other pictograms......................................................................................................................................6
1.2 Intended use.............................................................................................................................................7
1.3 Possible dangers caused by the circular metal saw.................................................................................8
1.4 Qualification of the staff............................................................................................................................8
1.4.1 Target group.............................................................................................................................................8
1.4.2 Authorized staff.........................................................................................................................................9
1.5 Operator positions ..................................................................................................................................10
1.6 Safety measures during operation..........................................................................................................10
1.7 Safety devices ........................................................................................................................................11
1.7.1 Protective cover on the saw blade..........................................................................................................11
1.7.2 Lockable main switch..............................................................................................................................12
1.7.3 EMERGENCY-STOP push button..........................................................................................................12
1.7.4 Prohibition, warning and mandatory labels.............................................................................................13
1.8 Personnel protective equipment .............................................................................................................14
1.9 Safety during operation...........................................................................................................................14
1.10 Safety during maintenance.....................................................................................................................14
1.10.1 Disconnecting and securing the circular metal saw................................................................................15
1.10.2 Using lifting equipment ...........................................................................................................................15
1.10.3 Mechanical maintenance work ...............................................................................................................15
1.11 Accident report........................................................................................................................................15
1.12 Electrical system.....................................................................................................................................15
2 Technical data
2.1 Electrical connection...............................................................................................................................16
2.2 Cutting area............................................................................................................................................16
2.3 General...................................................................................................................................................16
2.4 Dimensions.............................................................................................................................................16
2.5 Speed of saw blade................................................................................................................................16
2.6 Environmental conditions........................................................................................................................16
2.7 Operating material..................................................................................................................................16
2.8 Emissions ...............................................................................................................................................17
2.9 Dimensions CS 275................................................................................................................................18
2.10 Dimensions CS 315................................................................................................................................19
3 Delivery, interdepartmental transport, assembly and commissioning
3.1 Notes on transport, installation, commissioning .....................................................................................20
3.1.1 General risks during internal transport....................................................................................................20
3.2 Scope of delivery....................................................................................................................................21
3.3 Installation and assembly .......................................................................................................................21
3.3.1 Requirements to the installation site.......................................................................................................21
3.3.2 Fasten the substructure of the circular metal saw CS275 on the floor...................................................21
3.3.3 Fasten the substructure of the circular metal saw CS315 on the floor...................................................22
3.3.4 Mount the saw on the machine substructure..........................................................................................22
3.3.5 Mount the lever arm................................................................................................................................23
3.3.6 Mount the saw blade...............................................................................................................................24
3.4 First commissioning................................................................................................................................24
3.4.1 Checks....................................................................................................................................................24
3.4.2 Direction of the saw teeth.......................................................................................................................24
3.4.3 Check the oil level in the worm gear.......................................................................................................24
3.4.4 Refill coolant...........................................................................................................................................25
3.4.5 Electrical connection...............................................................................................................................25

Version 1.1.3 - 2020-07-30 3Translation of original operating manual
CS275 | CS315 EN
CS275_CS315_GBIVZ.fm
3.4.6 Electrical connection ..............................................................................................................................25
3.4.7 Check the running direction of the saw blade ........................................................................................25
4Operation
4.1 Safety.....................................................................................................................................................26
4.2 Control and indicating elements CS 275/ CS 315..................................................................................26
4.3 Inserting the workpiece ..........................................................................................................................27
4.4 Saw blade speed CS 275/ CS 315.........................................................................................................28
4.4.1 Speed change........................................................................................................................................28
4.4.2 Select the toothing and the shape of the tooth.......................................................................................29
4.5 Switch on the machine...........................................................................................................................30
4.6 Switching off the machine ......................................................................................................................30
4.7 Sawing of angles....................................................................................................................................31
4.8 Cooling...................................................................................................................................................32
5 Maintenance
5.1 Safety.....................................................................................................................................................33
5.1.1 Preparation.............................................................................................................................................33
5.1.2 Restarting...............................................................................................................................................33
5.2 Inspection and maintenance ..................................................................................................................34
5.3 Mounting and replacing the saw blade...................................................................................................36
5.3.1 Dimensions of sawing flange..................................................................................................................38
5.4 Repair.....................................................................................................................................................38
5.4.1 Customer service technician..................................................................................................................38
6 Ersatzteile - Spare parts
6.1 Ersatzteilbestellung - Ordering spare parts............................................................................................39
6.2 Hotline Ersatzteile - Spare parts Hotline ................................................................................................39
6.3 Service Hotline.......................................................................................................................................39
6.4 Einzelteile - Spare parts.........................................................................................................................40
6.5 Schaltplan - Wiring diagram...................................................................................................................42
6.6 Ersatzteilliste - Spare parts list - CS275.................................................................................................43
6.7 Ersatzteilliste - Spare parts list - CS315.................................................................................................47
7 Malfunctions
7.1 Malfunctions on the circular metal saw ..................................................................................................50
8Annex
8.1 Copyright................................................................................................................................................51
8.2 Terminology/Glossary ............................................................................................................................51
8.3 Change information manual ...................................................................................................................51
8.4 Liability claims for defects / warranty......................................................................................................51
8.5 Storage...................................................................................................................................................52
8.6 Advice for disposal / Options of re-use...................................................................................................53
8.7 Decommissioning...................................................................................................................................53
8.7.1 Disposal of the packaging of the new machine......................................................................................53
8.7.2 Disposal of the used machine ................................................................................................................53
8.7.3 Disposal of electrical and electronic components ..................................................................................53
8.7.4 Disposal of lubricants and cooling lubricants .........................................................................................54
8.8 Disposal via municipal collecting points.................................................................................................54
8.9 Product follow-up....................................................................................................................................54

Version 1.1.3 2020-07-30Page 4 Translation of the original instructions
CS275 | CS315GB
_preface_GB.fm
OPTIMUM
MASCHINEN - GERMANY
®
Preface
Dear customer,
Thank you very much for purchasing a product made by OPTIMUM.
OPTIMUM metal working machines offer a maximum of quality, technically optimum solutions and convince
by an outstanding price performance ratio. Continuous enhancements and product innovations guarantee
state-of-the-art products and safety at any time.
Before commissioning the machine please thoroughly read these operating instructions and get familiar with
the machine. Please also make sure that all persons operating the machine have read and understood the
operating instructions beforehand. 
Keep these operating instructions in a safe place nearby the machine.
Information
The operating instructions include indications for safety-relevant and proper installation, operation and main-
tenance of the machine. The continuous observance of all notes included in this manual guarantee the safety
of persons and of the machine.
The manual determines the intended use of the machine and includes all necessary information for its eco-
nomic operation as well as its long service life.
In the paragraph "Maintenance" all maintenance works and functional tests are described which the operator
must perform in regular intervals.
The illustration and information included in the present manual can possibly deviate from the current state of
construction of your machine. Being the manufacturer we are continuously seeking for improvements and
renewal of the products. Therefore, changes might be performed without prior notice. The illustrations of the
machine may be different from the illustrations in these instructions with regard to a few details. However,
this does not have any influence on the operability of the machine. 
Therefore, no claims may be derived from the indications and descriptions. Changes and errors are reserved!
Your suggestion with regard to these operating instructions are an important contribution to optimising our
work which we offer to our customers. For any questions or suggestions for improvement, please do not hesi-
tate to contact our service department.
If you have any further questions after reading these operating instructions and you are not able to solve your
problem with a help of these operating instructions, please contact your specialised dealer or directly the
company OPTIMUM.
Optimum Maschinen Germany GmbH
Dr.- Robert - Pfleger - Str. 26
D-96103 Hallstadt
Mail: [e-mail]
Internet: www.optimum-maschinen.com

Safety
Version 1.1.3 - 2020-07-30 5Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
1 Safety
Representation Conventions
This part of the operating instructions
explains the meaning and use of the warning notices included in these operating instruc-
tions,
defines the intended use of the circular metal saw,
points out the dangers that might arise for you or others if these instructions are not
observed,
informs you about how to avoid dangers.
In addition to these operation instructions, please observe
the applicable laws and regulations,
legal regulations for accident prevention,
the prohibition, warning and mandatory signs as well as the warning notes on the circular
metal saw.
European standards must be kept during installation, operation, maintenance and repair of the
circular metal saw.
If European standards are not applied at the national legislation of the country of destination,
the specific applicable regulations of each country are to be observed.
If necessary, the required measures must be taken to comply with the specific regulations of
each country before the circular metal saw is used for the first time.
Always keep this documentation close to the circular metal saw.
INFORMATION
If you are unable to solve a problem using these operating instructions, please contact us for
advice:
Optimum Maschinen Germany GmbH
Dr. Robert-Pfleger-Str. 26
D-96103 Hallstadt
email: [email protected]
gives additional advices
calls on you to act
enumerations

Safety
Version 1.1.3 - 2020-07-306 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_1.fm
1.1 Safety instructions (warning notes)
1.1.1 Classification of hazards
We classify the safety instructions into different levels. The table below gives an overview of the
classification of symbols (pictograms) and signal words for the specific danger and its (possible)
consequences.
1.1.2 Other pictograms
Pictogram Signal word Definition/Consequences
DANGER! Imminent danger that will cause severe injury of death to the staff.
WARNING! A danger that might cause severe injury to the staff or can lead to death.
CAUTION! Danger of unsafe procedure that might cause injury to the staff or property
damages.
ATTENTION!
Situation that could cause damage to the machine and products and other
types of damage.
No risk of injury to the staff.
INFORMATION
Application tips and other important or useful information and notes.
No dangerous or harmful consequences for the staff or objects.
In case of specific dangers, we replace the pictogram by
or
general danger with warning of injuries to hands, hazardous
electrical voltage, rotating parts.
Warning: danger of
slipping! Warning: risk of stumbling! Warning: hot surface! Warning: biological hazard!
Warning: automatic start-
up! Warning: tilting danger! Warning: suspended loads! Caution, danger of explosive substances!

Safety
Version 1.1.3 - 2020-07-30 7Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
1.2 Intended use
WARNING!
In the event of improper use, the circular metal saw
will endanger personnel,
the machine and other material property of the operating company will be endan-
gered,
the correct function of the machine may be affected.
The circular metal saw is designed and manufactured to be used in environments where there
is no potential danger of explosion.
The circular metal saw is designed and manufactured to saw cold metal, cast material and plas-
tics or other material that are not health hazardous and do not generate dust.
The circular metal saw must not be used on wood.
The pieces to be cut must be of a shape that will allow them to be securely attached in the
workholder vice and ensure that the piece does not come loose when it is being sawed.
The circular metal saw must only be installed and operated in a dry and ventilated place.
If the circular metal saw is used in any way other than described above, modified without
authorization of Optimum Maschinen Germany GmbH, then the circular metal saw is being
used improperly.
We do not take any liability for damages caused by intended use.
We expressly point out that the guarantee or CE conformity will expire due to any constructive
technical or procedural changes which had not been performed by the company Optimum
Maschinen Germany GmbH.
It is also part of intended use that
observe the limits of the circular metal saw,
the operating manual is constantly observed,
observe the inspection and maintenance instructions.
 Technical data on page 16
The decisive factor for achieving efficient cutting and the necessary angular tolerance is the
correct choice of parameters such as the saw blade, feed, cutting pressure, cutting speed and
cooling agent.
Switching on forbidden! Read the operating
instructions before
commissioning!
Pull out the mains plug! Wear protective glasses!
Wear protective gloves! Wear safety shoes! Wear a protective suit! Use ear protection!
Protect the environment! Contact address

Safety
Version 1.1.3 - 2020-07-308 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_1.fm
WARNING!
Extremely severe injuries.
It is forbidden to make any modifications or alternations to the operation values of the
circular metal saw ! They could endanger the staff and cause damage to the circular
metal saw.
1.3 Possible dangers caused by the circular metal saw
The circular metal saw is state-of-the-art, nevertheless, there is a residual risk as the circular
metal saw operates with,
electrical voltage and currents,
a running circular metal saw blade.
We have used construction resources and safety techniques to minimize the health risk for the
staff resulting from these hazards.
If the circular metal saw is used and maintained by the staff who are not duly qualified, there
may be a risk resulting from incorrect or unsuitable maintenance of the circular metal saw.
INFORMATION
All staff involved in assembly, commissioning, operation and maintenance, must
be duly qualified,
strictly follow these operating instructions.
In the event of intended use
there is a risk for the employee,
the circular metal saw and further property might be endangered,
the correct function of the circular metal saw may be affected.
Always disconnect the circular metal saw if cleaning or maintenance work is being carried out.
WARNING!
The circular metal saw may only be used with the safety devices activated.
Disconnect the circular metal saw immediately whenever you detect a failure in the
safety devices or when they are not mounted!
All additional devices installed by the operator have to be equipped with the prescribed
safety devices.
This is your responsibility being the operating company!
 Safety devices on page 11
1.4 Qualification of the staff
1.4.1 Target group
This manual is addressed to
the operating companies,
the operators,
the staff for maintenance works.
Therefore, the warning notes refer to both operation and maintenance of the circular metal saw.
Determine clearly and explicitly who will be responsible for the different activities on the
machine (operation, maintenance and repair).
Unclear responsibilities constitute a safety risk!
Disconnect the main plug of the circular metal saw and secure the circular metal saw against
restarting.
The qualifications of the staff for the different tasks are mentioned below:

Safety
Version 1.1.3 - 2020-07-30 9Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
Operator
The operator is instructed by the operating company about the assigned tasks and possible
risks in case of improper behaviour. Any tasks which need to be performed beyond the opera-
tion in the standard mode must only be performed by the operator if it is indicated in these
instructions and if the operating company expressively commissioned the operator.
Electrical specialist
Due to his professional training, knowledge and experience as well as his knowledge of respec-
tive standards and regulations the electrical specialist is able to perform works on the electrical
system and to recognise and avoid any possible dangers himself.
The electrical specialist is specially trained for the working environment in which he is working
and knows the relevant standards and regulations.
Specialist staff
Due to his professional training, knowledge and experience as well as his knowledge of rele-
vant regulations the specialist staff is able to perform the assigned tasks and to recognise and
avoid any possible dangers himself.
Instructed persons
Instructed persons were instructed by the operating company about the assigned tasks and any
possible risks in case of improper behaviour.
1.4.2 Authorized staff
CAUTION!
Inappropriate operation and maintenance of the circular metal saw constitutes a danger
for the staff, objects and the environment.
Only authorized staff may operate the circular metal saw !
Persons authorized to operate and maintain should be trained technical staff and instructed by
the ones who are working for the operating company and for the manufacturer.
The operating company must
Obligations of the
operating
company
train the staff,
instruct the staff in regular intervals (at least once a year) on
- all safety standards that apply to the machine,
- the operation,
- accredited technical guidelines,
check staff‘s state of knowledge,
document the trainings/instructions,
require staff to confirm participation in training/instructions by means of a signature,
check whether the staff is working safety- and risk-conscious and observe the operating
instructions.
The operator must
Obligations of the
operator
have obtained a training regarding the handling of the circular metal saw,
know the function and mode of action,
before taking the machine in operation
- have read and understood the operating manual,
- be familiar with all safety devices and instructions. Further
requirements to
the qualification
For work on the following parts there are additional requirements:
Electric components or operating materials: Must only be performed by a qualified electri-
cian or person working under the instructions and supervision of a qualified electrician.

Safety
Version 1.1.3 - 2020-07-3010 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_1.fm
Before starting work on electrical parts or operating agents, following measures need
to be performed in the following order.
- disconnect all poles.
- secure against switching-on
- check dead circuit
1.5 Operator positions
The operator position is in front of the circular metal
saw.
INFORMATION
The mains plug of the circular metal saw must be
freely accessible.
Img.1-1: Operator positions
1.6 Safety measures during operation
CAUTION!
Risk by inhaling health hazardous dusts and fogs.
Depending on the materials which need to be treated and the agents which are used,
dusts and fogs may be generated which endanger your health.
Make sure that the generated health hazardous dusts and fogs are safely sucked-off at
the place of origin and that they are dissipated or filtered. To do so, use a suitable
extraction unit.
CAUTION!
Risk of fire and explosion by using inflammable materials or cooling-lubricating agents.
Before processing inflammable materials (e.g. aluminium, magnesium) or using
inflammable auxiliary materials (e.g. spirit) it is necessary to take additional preventive
measures in order to safely avoid health risks.

Safety
Version 1.1.3 - 2020-07-30 11Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
1.7 Safety devices
Use the circular metal saw only with properly functioning safety devices.
Stop the circular metal saw immediately if there is a failure on the safety device or if it is not
functioning for any reason.
It is your responsibility!
If a safety device has been activated or has failed, the circular metal saw must only be used if
you
have removed the cause of the failure,
have verified that there is no danger resulting for the staff or objects.
WARNING!
If you bypass, remove or override a safety device in any other way, you are endangering
yourself and other persons working on the circular metal saw. The possible
consequences are
injuries may occur due to workpiece or parts of workpieces flying off,
contact with rotating and revolting parts,
fatal electrocution.
WARNING!
The separating protective equipment which is made available and delivered together
with the machine is designed to reduce the risk of workpieces or fractions of them which
being expelled, but not to remove them completely. Always work carefully and observe
the limit values of your chipping process.
1.7.1 Protective cover on the saw blade
The saw blade of the circular metal saw is equipped with a protective cover. The protective
cover covers the circulatory saw blade.
WARNING!
Danger of injury! The teeth of the saw blade are sharp. Take great care when opening the
protective cover to change the saw blade.
Wear protective gloves.
Img.1-2: Protective cover
Protective cover

Safety
Version 1.1.3 - 2020-07-3012 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_1.fm
1.7.2 Lockable main switch
In the position " 0 " the lockable main switch can be secured against accidental or non-author-
ized switching-on by means of a padlock.
When the main switch is switched-off, the current supply is interrupted.
Except for the areas marked by the pictogram in the margin.
Img.1-3: Main switch
WARNING!
Dangerous voltage even if the main switch is switched-off. In the areas marked by
pictogram in the margin, there might be voltage, even if the main switch is switched-off.
1.7.3 EMERGENCY-STOP push button
The EMERGENCY-STOP button switches the circular metal saw off.
INFORMATION
After actuation turn the EMERGENCYSTOP button clockwise in order turn the circular metal
saw on again.
Img.1-4: EMERGENCY-STOP push button
Main switch
EMERGENCY-STOP push
button

Safety
Version 1.1.3 - 2020-07-30 13Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
1.7.4 Prohibition, warning and mandatory labels
INFORMATION
All warning signs must be legible.
Check them regularly.
Position of labels on the circular metal saw:
Img.1-5: Circular metal saw CS 275/ CS 315
Check the circular metal saw at least once per shift. Inform the person responsible immediately
of any damage, defect or change in the operating function.
Check all safety devices
at the beginning of each shift (with the machine stopped),
once a week (with the machine in operation),
after every maintenance and repair work.
Check that prohibition, warning and information signs and the labels on the circular metal saw
are legible (clean them, if necessary),
are complete.

Safety
Version 1.1.3 - 2020-07-3014 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_1.fm
1.8 Personnel protective equipment
For some works you need personnel protective equipment as protective equipment. These are
safety helmet,
protective glasses or face guard,
protective gloves,
safety shoes with steel caps,
ear protection.
Before starting work, make sure that the prescribed protective equipment is available at the
workplace.
CAUTION!
Dirty or contaminated personnel protective equipment can cause diseases. Clean it each
time after use and once a week.
Personal protective equipment for special works
Protect your face and eyes: wear a safety helmet with facial protection when performing works
where your face and eyes are exposed to hazards.
Use protective gloves when handling pieces with sharp edges.
Use safety shoes when you assemble, disassemble or transport heavy components.
1.9 Safety during operation
We specially point out the specific dangers when working with and on the circular metal saw.
CAUTION!
Before switching on the circular metal saw make sure that there are
no dangers generated for persons,
no objects are damaged.
Avoid any risky working practices:
Make sure that nobody is endangered by your work.
The instructions mentioned in these operating instructions have to be strictly observed dur-
ing assembly, operation, maintenance and repair.
Do not work on the circular metal saw, if your concentration is reduced, for example,
because you are taking medication.
Observe the accident prevention regulations issued by your Employers Liability Insurance
Association or other competent supervisory authority, responsible for your company.
Stay at the circular metal saw until all movements have come to a complete standstill.
Use the prescribed personnel protective equipment. Make sure to wear a well-fitting work
suit and, if necessary, a hairnet.
Inform the supervisor about all endangerments or errors.
1.10 Safety during maintenance
Report and
document any
changes
Inform the operators on time of any maintenance and repair work.
Report all safety relevant changes and performance details of the circular metal saw. Document
all changes, have the operating instructions updated accordingly and train machine operators.

Safety
Version 1.1.3 - 2020-07-30 15Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_1.fm
1.10.1 Disconnecting and securing the circular metal saw
Disconnect the main plug of the circular metal saw and secure the circular metal saw against
restarting.
Place a warning sign on the machine.
1.10.2 Using lifting equipment
WARNING!
The use of unstable lifting and load suspension gear that might break under load can
cause severe injuries or even death.
Check that the lifting and load suspension gear is
sufficient load capacity
and that it is in perfect condition.
Observe the accident prevention regulations issued by your Employers Liability
Insurance Association or other competent supervisory authority, responsible for your
company.
Fasten the loads properly.
Never walk under suspended loads!
1.10.3 Mechanical maintenance work
Remove or install protection safety devices before starting any maintenance work and re-install
them once the work has been completed.This includes:
Covers,
Safety indications and warning signs,
Earth (ground) connections.
If you remove protective or safety devices, re-fit them immediately after the completing the
work.
Check if they are working properly!
1.11 Accident report
Inform your superiors and Optimum Maschinen Germany GmbH immediately in the event of
accidents, possible sources of danger and any actions which almost led to an accident (near
misses).
There are many possible causes for "near misses".
The sooner they are notified, the faster the causes can be eliminated.
INFORMATION
We point out the specific dangers when performing works with and on the circular metal saw
when describing such works.
1.12 Electrical system
Have the machine and/or the electrical equipment checked regularly, at least every six months.
Immediately eliminate all defects such as loose connections, defective wires, etc.
A second person must be present during work on live components to disconnect the power in
the event of an emergency.
Disconnect the circular metal saw immediately if there is a malfunction in the power supply !
 Maintenance on page 33,  Schaltplan - Wiring diagram on page 42

Technical data
Version 1.1.3 - 2020-07-3016 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_2.fm
2 Technical data
The following information are the dimensions and indications of weight and the manufacturer‘s
approved machine data.
2.1 Electrical connection CS 275 CS 315
Connection 400 V ~ 50 Hz (~60Hz)
2 KW / 1.4 KW 400 V ~ 50 Hz (~60Hz) 1.5 KW / 0.75 KW
Cooling pump 400 V ~ 50 Hz
40 W 400 V ~ 50 Hz 40 W
2.2 Cutting area CS 275 CS 315
900round, max. 60 mm 85 mm
900rectangular, max. 100 x 60 mm 130 x 70 mm
900square, max. 60 x 60 70 x 70
450round, max. 60 mm 85 mm
450rectangular, max. 70 x 60 mm 90 x 70 mm
450square, max. 60 x 60 70 x 70
Cutting angle -450-+450
2.3 General CS 275 CS 315
Cutting angle adjustment over turnable bearing block
Feed manually
Material tension manual in the quick-action vice
2.4 Dimensions CS 275 CS 315
Saw blade diameter [mm] 275 315
 Dimensions of sawing flange on page 38
Range vice 110 mm 145 mm
2.5 Speed of saw blade CS 275 CS 315
Two-step drive engine [m/min] 41 (~50Hz) 82 (~50Hz) 19 (~50Hz) 38 (~50Hz)
2.6 Environmental conditions CS 275 CS 315
Temperature 5-35 °C
Humidity 5 - 80 %
2.7 Operating material CS 275 CS 315
Worm gear Mobilgear 629, viscosity 40°C 150 mm2/s , at 100°C 16 mm2/
s ISO VG 150
Spindle of the machine vice Commercial heavy grease

Technical data
Version 1.1.3 - 2020-07-30 17Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_2.fm
2.8 Emissions
The generation of noise emitted by the circular metal saw is less than 80 dB(A).
If the circular metal saw is installed in an area where various machines are in operation, the
noise exposure (immission) on the operator of the circular metal saw at the working place may
exceed 85 dB(A).
INFORMATION
This numerical value was measured on a new machine under proper operating conditions.
Depending on the age respectively on the wear of the machine it is possible that the noise
behaviour of the machine changes.
Furthermore, the factor of the noise emission is also depending on manufacturing influencing
factors,e.g. speed, material and clamping conditions.
INFORMATION
The mentioned numerical value is the emission level and not necessarily a safe working level.
Though there is a dependency between the degree of the noise emission and the degree of the
noise disturbance it is not possible to use it reliably to determine if further precaution measures
are required or not.
The following factors influence the actual degree of the noise exposure of the operator:
Characteristics of the working area, e.g. size or damping behaviour,
Other noise sources, e.g. the number of machines,
Other processes taking place in the proximity and the period of time during which the op-
erator is exposed to the noise.
Furthermore, it is possible that the admissible exposure level might be different from country to
country due to national regulations.
This information about the noise emission shall allow the operator of the machine to more eas-
ily evaluate the endangering and risks.
CAUTION!
Depending on the overall noise exposure and the basic limit values the machine
operators must wear an appropriate hearing protection.
We generally recommend to use a noise protection and a hearing protection.
Slide bearing Commercial heavy grease
Bare steel parts e.g. machines oil (Mobil Oil, Fina, ...) motor oil, motor oil is
acid-, stain- and resin-free.
2.7 Operating material CS 275 CS 315

Technical data
Version 1.1.3 - 2020-07-3018 Translation of original instruction
CS275 | CS315
EN
CS275_CS315_GB_2.fm
2.9 Dimensions CS 275
Img.2-1: Dimensions CS 275

Technical data
Version 1.1.3 - 2020-07-30 19Translation of original instruction
CS275 | CS315 EN
CS275_CS315_GB_2.fm
2.10 Dimensions CS 315
Img.2-2: Dimensions CS 315

Delivery, interdepartmental transport, assembly and commissioning
Version 1.1.3 - 2020-07-3020 Translation of original instruction
EN
in-house_transport_en.fm
3 Delivery, interdepartmental transport, assembly and
commissioning
3.1 Notes on transport, installation, commissioning
Improper transport, installation and commissioning is liable to accidents and can cause damage
or malfunctions to the machine for which we do not assume any liability or guarantee.
Transport the scope of delivery secured against shifting or tilting with a sufficiently dimen-
sioned industrial truck or a crane to the installation site.
WARNING!
Severe or fatal injuries may occur if parts of the machine tumble or fall down from the
forklift truck or from the transport vehicle. Follow the instructions and information on the
transport box.
Note the total weight of the machine. The weight of the machine is indicated in the "Tech-
nical data" of the machine. When the machine is unpacked, the weight of the machine
can also be read on the rating plate.
Only use transport devices and load suspension gear that can hold the total weight of
the machine.
WARNING!
The use of unstable lifting and load suspension equipment that might break under load
can cause severe injuries or even death. Check that the lifting and load suspension gear
has sufficient load-bearing capacity and that it is in perfect condition.
Observe the accident prevention regulations issued by your Employers Liability Insur-
ance Association or other competent supervisory authority, responsible for your com-
pany. Fasten the loads properly.
3.1.1 General risks during internal transport
WARNING: TILTING DANGER!
The machine may be lifted unsecured by a maximum of 2 cm.
Employees must be outside the danger zone, i.e. the reach of the load.
Warn employees and advise them of the hazard.
Machines may only be transported by authorized and qualified persons. Act responsibly during
transport and always consider the consequences. Refrain from daring and risky actions.
Gradients and descents (e.g. driveways, ramps and the like) are particularly dangerous. If such
passages are unavoidable, special caution is required.
Before starting the transport check the transport route for possible danger points, unevenness
and faults.
Danger points, unevenness and disturbance points must be inspected before transport. The
removal of danger spots, disturbances and unevenness at the time of transport by other
employees leads to considerable dangers.
Careful planning of interdepartmental transport is therefore essential.