CHIEF FMSITL User manual

I N S T A L L A T I O N I N S T R U C T I O N S
FCASFP
FMSIML
FMSITL
Menu Board Interface Kits
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCASFP / FMSIML / FMSITL

FCASFP / FMSIML / FMSITL Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all parts are properly
assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which the mounting system is
attached can support five times the combined weight of all
equipment.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the accessory does not exceed
the weight capacity listed in Table 1.
Table 1: Weight Capacity
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
Maximum Weight Allowed
FCASFP 75 lbs (34.0 kg)
FMSIML 125 lbs (56.7 kg)
FMSITL 125 lbs (56.7 kg)
TABLE OF CONTENTS
FMSITL.........................................................11
FMSIML..........................................................7
FCASFP..........................................................3

Installation Instructions FCASFP / FMSIML / FMSITL
3
DIMENSIONS
LEGEND
12.50
317.5
DIMENSIONS: INCHES
[MILLIMETERS]
FCASFP
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
FCASFP

FCASFP / FMSIML / FMSITL Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION - FCASFP
PARTS - FCASFP
#2
3/8"
A (4)
M4x12mm B (4)
M4x20mm C (4)
M4x25mm
E (4)
M5x20mm F (4)
M5x25mm G (4)
M6x12mm
I (4)
M6x25mm
J (4)
M8x12mm K (4)
M8x20mm
M (4)
[Nesting spacer] N (4)
[Universal washer]
Locking Hardware Kit
P (2)
10-24 x 5/8"
Q (2)
10-24
R (1)
[Left interface bracket]
S (1)
[Right interface bracket]
DISPLAY ATTACH HARDWARE BAG
(Letters correspond to letters on bag)
D (4)
M5x12mm
H (4)
M6x20mm
L (4)
M8x30mm

Installation Instructions FCASFP / FMSIML / FMSITL
5
INSTALL INTERFACE BRACKETS TO
DISPLAYS
1. Raise the latch mechanism on both interface brackets (R
and S) to the OPEN position. (See Figure 1)
Figure 1
2. Place displays face down on a soft, non-abrasive surface.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
3. Select screw diameter by examining hardware (A-L) and
comparing with mounting holes on display. (See Figure 2)
4. Select spacers:
• Spacers are NOT required if mounting holes are
not recessed and interface brackets (R and S)
can lay flat against display.
• Nesting spacers (M) ARE required if mounting
holes are recessed, or if protrusions prevent
interface brackets (R and S) from laying flat.
5. Select screw length: (See Figure 2)
• By hand, insert SHORTEST length screw of
selected diameter (A, D, G or J) through universal
washer (N - if required), bracket (R or S), selected
spacer (M-if required), into display mounting hole.
Do NOT thread screw into hole at this time.
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (N) ONLY with M4, M5
and M6 screws.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
6. Align the center of the interface brackets (R and S) with
center of screen. (See Figure 2)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
7. Use selected screws (A-L), universal washers (N-if required)
and nesting spacers (M-if required), to connect interface
brackets (R and S) to back of display. (See Figure 2)
Figure 2
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (N) only with M4, M5
and M6 screws.
NOTE: The nesting spacers (M) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 3)
Figure 3
1
Latch
mechanism
(R)
(S)
Latch
mechanism
already raised
LATCH CLOSED
LATCH OPEN
(N)
Center of
bracket
(A-L)
7
6
(MA or MB)
NOTE: Use universal washer (N) ONLY with M4, M5 and
M6 screws.
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]

FCASFP / FMSIML / FMSITL Installation Instructions
6
ATTACH DISPLAYS TO MOUNTING RAIL
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays must
be located approximately evenly across the length of the rail.
1. Ensure that the latch mechanisms on interface brackets (R
and S) are already raised to the OPEN position. (See
Figure 1)
CAUTION: BEFORE adding displays to the mounting rails,
ensure end caps (FMSECAP) are in place at BOTH ends of
mounting rail following instructions included with the
FMSECAP.
2. While supporting both sides of display, lower display onto
mounting rail, hooking top of interface brackets onto top of
mounting rail. (See Figure 4)
3. Lower the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 4)
Figure 4
4. Repeat for remaining interface bracket.
Interface Bracket Adjustment
CAUTION: ALWAYS keep a small distance between
screens when making adjustments! Damage to screens
possible if placed too close together.
Tilt
The interface brackets allow 0° to 20° tilt, and can be locked at
0°, 10° and 20° tilt.
5. If necessary, loosen button head tilt friction bolt (located on
side of interface bracket). (See Figure 5)
6. Adjust tilt as required. (See Figure 5)
7. The tilt may be locked at 0°, 10° and 20° using one
10-24 x 5/8" Phillips head screw (P) and one 10-24 lock nut
(Q) per interface bracket. (See Figure 5)
8. Tighten tilt friction bolt as necessary.
Figure 5
OPTIONAL: Security
1. OPTIONAL: Add padlock (not included) to each interface
bracket to lock display to mounting rail. (See Figure 6)
Figure 6
23
Latch
mechanism
Lock at
Lock at
Lock at
Tilt
friction
bolt
5
6
8
(Displays not shown)
7
(P)
(Q)
0° tilt
10° tilt
20° tilt
Padlock
(Optional)
(Displays not shown)

FCASFP / FMSIML / FMSITL Installation Instructions
7
DIMENSIONS
LEGEND
1.75
44.5
2.54
64.6
0.69
17.5
0.63
15.9
15.75
400.0
7.87
200.0
0.34
8.7
0.49
12.5
1.97
50.0
1.59
40.5
6.00
152.4
3.13
79.6
2.41
61.1
3/4" TOTAL
HEIGHT ADJUST
3/4" TOTAL
IN/OUT ADJUSTMENT
3/4" TOTAL
IN/OUT ADJUSTMENT
ADJUSTMENTS SHOWN
AT MIDPOINT
DIMENSIONS: INCHES
[MILLIMETERS]
FMSIML
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
FMSIML

Installation Instructions FCASFP / FMSIML / FMSITL
8
TOOLS REQUIRED FOR INSTALLATION - FMSIML
PARTS - FMSIML
#2
3/16"
K (1)
[Left interface bracket]
J (1)
[Right interface bracket]
A (4)
M6 x 12mm B (4)
M6 x 16mm C (4)
M6 x 30mm D (4)
1/4" E (4)
.750x.344x.500
F (4)
M8 x 12mm
G (4)
M8 x 16mm H (4)
M8 x 25mm
I (2)
1/4-20 x 1-1/4"
DISPLAY ATTACH HARDWARE BAG
(Letters correspond to letters on bag)

Installation Instructions FCASFP / FMSIML / FMSITL
9
INSTALL INTERFACE BRACKETS TO
DISPLAYS
1. Place displays face down on a soft, non-abrasive surface.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select screw diameter by examining hardware (A-C and
F-H) and comparing with mounting holes on display. (See
Figure 6)
3. Select spacers:
• Spacers are NOT required if mounting holes are
not recessed and interface brackets (J and K) can
lay flat against display.
•Spacers (E) ARE required if mounting holes are
recessed, or if protrusions prevent interface
brackets (J and K) from laying flat.
4. Select screw length: (See Figure 6)
• By hand, insert SHORTEST length screw of
selected diameter (A or F) through 1/4" washer
(D), bracket (J or K), selected spacer (E, if
required), into display mounting hole. Do NOT
thread screw into hole at this time.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
5. Align the center of the interface brackets (J and K) with
center of screen. (See Figure 6)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
6. Use selected screws (A-C or F-H), washers (D) and spacers
(E), if necessary, to connect interface brackets (J and K) to
back of display. (See Figure 6)
Figure 6
(E) x 4, if required
(K)
(J)
(A-C or F-H) x 4
6
(D) x 4
Match diamond with
center of display
5

FCASFP / FMSIML / FMSITL Installation Instructions
10
ATTACH DISPLAYS TO MOUNTING RAIL
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays must
be located approximately evenly across the length of the rail.
1. Ensure that the latch mechanisms on interface brackets (J
and K) are already raised to the OPEN position. (See
Figure 7)
CAUTION: BEFORE adding displays to the mounting rails,
ensure end caps (FMSECAP) are in place at BOTH ends of
mounting rail following instructions included with the
FMSECAP.
2. While supporting both sides of display, lower display onto
mounting rail, hooking top of interface brackets onto top of
mounting rail. (See Figure 7)
Figure 7
3. Raise latch on interface bracket and close into place against
mounting rail. (See Figure 7)
4. Fasten latch into place using one 1/4-20 x 1-1/4" socket
head screw (I). (See Figure 7)
NOTE: Socket head screws (I) must engage through both
holes to be fully secured. (See Figure 7)
5. Repeat for each interface bracket on the mounting rail.
Interface Bracket Adjustment
CAUTION: ALWAYS keep a small distance between
screens when making adjustments! Damage to screens
possible if placed too close together.
6. Move displays so that screens are nearly flush and level
with each other.
7. Use upper knob on back of interface brackets (J and K) to
adjust the height of each display. (See Figure 8)
NOTE: Adjust both brackets in order to maintain a level mount.
8. Use middle and lower knobs on back of interface brackets
(J and K) to make plumb adjustments to each display. (See
Figure 8)
Figure 8
1
Latch
4
(I) x 2
3
NOTE: Secure
screw (I)
through both
holes.
OPEN
Latch
CLOSED
7
8
8
(Display not shown for clarity)
7