CHIEF Kontour KRA243 User manual

I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
(shown with K2C120)
Kontour™ Interface Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KRA243

KRA243 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Kontour™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the Kontour Arm with the KRA243
accessory up to (and including) the display does not exceed
the weight limits for that mount. Use with products heavier
than the maximum weight indicated may result in collapse of
the mount and its accessories causing possible injury.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The KRA243 accessory is designed to
be used only with K1 Series Kontour mounts. Do NOT
attempt to install onto any other mounting system.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
INTERFACE ROTATION
TENSION SCREW
4.55
115.6
4.55
115.6
MOUTING PATTERN
COMPATIBILITY
100X100
75X75
INTERFACE
ROTATION
RANGE
90
0.80
20.2

Installation Instructions KRA243
3
TOOLS / PARTS FOR INSTALLATION
A (1)
[KRA243 faceplate]
1/8" (included)
C (4)
B (4) D (4)
E (1) G (1)
1/8"
F (1)
M4x10mm M4x20mm M10x5.3x10
#10-32 x 3/8"
M4 x 4mm
ASSEMBLY AND INSTALLATION
Mounting to K1 Mounts
1. Refer to K1 Series Installation Instructions to use hardware
B-D to mount display(s) to faceplate(s) (A).
2. Position display with faceplate (A) attached above mount.
(See Figure 1)
3. Slide faceplate (A) onto mounting head until quick release
tab clicks into place. (See Figure 1)
Figure 1
Rotational Adjustment
NOTE: (Optional) Rotational adjustment may be locked by
installing rotational locking screw (F) into back of
faceplate. (See Figure 2)
Figure 2
4. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
2)
5. Use Phillips screwdriver to adjust rotational adjustment
screw to adjust rotational tension. (See Figure 2)
Display Removal Security Screw
NOTE: In order to prevent display from being easily removed
from mount using the quick release lever, install
M4x4mm security screw (F) into lower hole on back of
faceplate. (See Figure 3)
Figure 3
3
(F)
5
(F)

KRA243 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003108 Rev00
2018 Milestone AV Technologies
www.milestone.com
11/18