CHIEF OLCB1U User manual

I N S T A L L A T I O N I N S T R U C T I O N S
OLCB1U
(Shown installed to
ODAC Series extension column)
Back-to-Back Large Flat Panel Outdoor Ceiling
Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
OLCB1U

OLCB1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
OLCB1U mounts does not exceed 250 lbs (113.4 kg) total or
125 lbs (56.7 kg) per display.
NOTE: "Moment" ratings have NOT been evaluated by UL.
WARNING: Exceeding the maximum moment can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the mounting system
does not exceed a moment of 2000 ft-lbs. See table below for
specific column specifications.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Use this mounting system with other outdoor
products only.
WARNING: Always use two people or a mechanical lifting
device to safely lift and position equipment.
NOTE: The OLCB1U flat panel floor/ceiling mounts are
intended to be used with UL Listed ODAC Series
columns (not included): ODAC0203, ODAC0304,
ODAC0405, ODAC0506, ODAC0708.
--SAVE THESE INSTRUCTIONS--
COLUMN
MODEL
Weight
capacity
Moment
Length (IN)
(ML)
Max
Design
Moment
(FT-LBS)
(MDM)
ODAC0203B 300 lbs (136 kg) 23 min - 36 max 2000
ODAC0304B 300 lbs (136 kg) 33 min - 48 max 2000
ODAC0405B 300 lbs (136 kg) 45 min - 60 max 2000
ODAC0506B 300 lbs (136 kg) 57 min - 72 max 2000
ODAC0708B 300 lbs (136 kg) 81 min - 96 max 2000
125
125

Installation Instructions OLCB1U
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]
1.91
48.4
0° HOLE
LOCKOUT
+5°AND -15°
HOLE LOCKOUT
-5° AND -20°
HOLE LOCKOUT
+7.6° HOLE
LOCKOUT
- 10°
2.48
63.0
-10° HOLE
LOCKOUT

OLCB1U Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main

Installation Instructions OLCB1U
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/2"
5/32" (included)
9/16”
D (4)
E (4)
[Interface Bracket Hardware Kit] - 2 (Qty per bag)
B (4) C (4)
A (4)
F (4) G (4)
J (1)
M6x25mm M8x20mm M8x30mm
M6x16mm
.750x.323x.250.750x.344x.500 5/16"
L (4)
[Interface bracket]
1/4-20 x 1 1/4"
H (1)
[Mount assembly]
P (1)
5/16-18 x 2"
W (4)
3/8"
N (1)
1/4-20 x 2"
Q (1)
1/4-20
R (1)
5/16-18 S (2)
5/16" T (2)
1/4"
U (2)
3/8-16 x 4" V (2)
3/8-16
M (1)
#10-24 x 1/2"
[Interface Lockout Bag] - (4) - (Qty per bag)
[Box-column Hardware Kit]
K (1)
5/32"

OLCB1U Installation Instructions
6
INSTALLATION
IMPORTANT ! : The following procedure assumes that:
• a UL Listed ODAC Series Floor/Ceiling Column
(not included) has been properly installed
following instructions provided with plate and
pipe.
Attaching Mount to ODAC Series Column
CAUTION: WATCH FOR PINCH POINTS! Do not place
fingers between movable parts.
1. Slide mount assembly (H) onto ODAC Series Floor/Ceiling
Column. (See Figure 1) or (See Figure 2)
2. Use two 3/8-16 x 4" hex head tapping bolts (U), four 3/8"
washers (W) and 3/8-16 hex nuts (V). (See Figure 1) or
(See Figure 2)
Figure 1
Figure 2
3. Install 1/4-20 x 1 1/4" button head cap screw (J) into mount
assembly (H) to prevent column from rattling. (See Figure 3)
Figure 3
1
2
(U) x 2
(W) x 4
(V) x 2
2
(H)
(To Ceiling)
1
2
(U) x 2
(W) x 4
(V) x 2
2
(H)
(To Floor)
(J)
3
(H)

Installation Instructions OLCB1U
7
Attaching Interface Brackets to Display
1. Lower the latch mechanism on each interface bracket (L).
(See Figure 4)
Figure 4
2. Align the center of the interface bracket (L) with center of
screen. (See Figure 5)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
Figure 5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
3. Select correct screws, spacers (if necessary) and universal
washers from the hardware bag (A-G) and attach brackets
(L) to back of screen. (See Figure 5)
Attaching Display to Ceiling Mount
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
OLCB1U mounts does not exceed 250 lbs (113.4 kg) total or
125 lbs (56.7 kg) per display.
1. Ensure that the latch mechanisms on interface brackets (L)
are already lowered. (See Figure 4)
2. While supporting both sides of display, lower display onto
ceiling mount, hooking top of interface brackets onto front of
ceiling mount. (See Figure 6)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The display MUST
be centered on the ceiling mount.
3. Raise the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 6)
Figure 6
(L) x 2
1
Latch
mechanism
Center of
bracket
(E or F) x 4
(A-D) x 4
(L) x 2
3
2
(G) x 4
(if necessary)
2
3
Latch
mechanism

OLCB1U Installation Instructions
8
4. Fasten brackets against ceiling mount extrusion using #10-
24 x 1/2" socket head cap screws (M). (See Figure 7)
5. Repeat for other interface bracket.
Figure 7
6. Repeat Steps 1-5 to install display to the other side of the
mount.
Adjustments
CAUTION: Watch for pinch points! Do not place fingers
between movable parts.
Yaw
The ceiling mounts allows yaw adjustment in 45° increments in
each direction.
1. Remove two bolts and washers connecting column collar to
mount assembly box. (See Figure 8)
2. Adjust yaw in 45° increment until desired position is
achieved. (See Figure 8)
3. Reinstall bolts and washers removed in Step 1. (See Figure
8)
Figure 8
Tilt
CAUTION: Watch for pinch points! Do not place fingers
between movable parts.
The interface brackets allow -7.6° to 20° tilt, and can be locked
at -7.6°, -5°, 0°, 5°, 10°, 15° and 20° tilt. (See Figure 9)
Figure 9
4
(M)
(wind shield hidden for clarity)
1
column collar
3
2
+/- 45°
1.91
48.4
0° HOLE
LOCKOUT
+5°AND -15°
HOLE LOCKOUT
-5° AND -20°
HOLE LOCKOUT
+7.6° HOLE
LOCKOUT
- 10°
2.48
63.0
-10° HOLE
LOCKOUT

Installation Instructions OLCB1U
9
4. If necessary, loosen button head tilt friction bolt (located on
side of interface bracket). (See Figure 10)
5. Adjust tilt as required. (See Figure 10)
6. The tilt may be locked at -7.6°, -5°, 0°, 5°, 10°, 15° and 20°
using one 1/4-20 x 2" Phillips head screw (N), one 1/4-20
lock nut (Q) and two 1/4" washers (T) per interface bracket.
(See Figure 9) and (See Figure 10)
NOTE: Use of washers (T) is optional.
7. Tighten button head tilt friction bolt as necessary.
Figure 10
Roll
1. Adjust roll adjustment screw to change roll position.The roll
may be adjusted 3° in either direction. (See Figure 11)
Figure 11
Latch Lock/Security
IMPORTANT ! : In order to prevent interface latch from
getting loose due to strong winds, the latch MUST be
locked either using a padlock or locking bolt (N) and 5/
16-18 hex nuts (Q). This is NOT optional!
Using Padlocks (Security)
1. Add padlock (not included) to each interface bracket to lock
latch and to provide security for displays. (See Figure 12)
Figure 12
Using Bolts/Nuts
NOTE: This will keep latch from opening but does not provide
additional security for the displays.
1. Use 5/16-18 x 2" hex head carriage bolt (P), 5/16-18 hex nut
(R) and two 5/16" washers (S) to lock each interface bracket
latch in place. (See Figure 13)
Figure 13
Tilt
friction
bolt
4
4
7
(Displays not shown)
6
(N)
(Q)
0° tilt
20° tilt
5
(T) x 2
roll adjustment screw
or
Padlock
(Optional)
(P)
(R)
(S) x 2

OLCB1U Installation Instructions
10