Childcare ASSISTED AUTO CLOSE 089346-003 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
ASSISTED AUTO CLOSE
GATE “WHITE”
#089346-003
730mm - 940mm 749mm

PLEASE NOTE - IMPORTANT NOTICE
Please keep in mind, when removing gate from carton that the gate may
seem visually distorted or faulty; THIS IS NOT THE CASE.
The gate is designed in this shape in order to ensure that when the top
ADJUSTERS are correctly adjusted,the GATE FRAME is straightened ensuring
the correct pressure is acheived.
GATE WHEN REMOVED FROM CARTON
GATE STRAIGHTENED WHEN INSTALLED TO THE WALL
WIDE GAP
NARROW GAP
GATE LOCK
GATE FRAME
ADJUSTER

This gate is designed for children from 6 months to 24 months. Since
each child’s skills develop at different ages,these parameters should be
monitored against your child’s own development.
Read all instructions before assembly and use of the safety gate. Keep
instructions for future use.
Intended for use with children from 6 months through 24 months.
Check the stability of the gate and tighten all hardware and mountings regularly.
To prevent serious injury or death, securely install gate or enclosure and use according to
manufacturer’s instructions.
Install according to the manufacturer’s instructions.
NEVER use with a child able to climb over or dislodge/open the gate or enclosure.
NEVER use if gate is less than 3/4 of child’s height.
DO NOT use if any part of the gate is broken or missing.
This product will not necessarily prevent all accidents.Never leave child unattended.
Use only spare parts available from cnp brands.
NEVER allow child to climb or swing on gate.
Use only with the locking/latching mechanism securely engaged.
NEVER use gate at top of stairs.
Discontinue use if any part of the gate is damaged.
NEVER climb over the gate.
NEVER hang or tie toys,etc,to any part of the gate.
SAFETY PRECAUTIONS
WARNING
730mm - 800mm (no extension)
800mm - 870mm (with 1 extension)
870mm - 940mm (with 2 extensions)
Gate Opening Size:

Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Assisted Auto Close Gate
Congratulations on your purchase of the Assisted Auto
Close Gate“White”
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Gate Section
Lower extension
housing
Spindle Housing
Extension tube
x 1
x 2 x 4
x 4
x 2
x 4
x 2
x 2
x 2
x 2
Bottom Spindle
Top Spindle
Extension Bar
Upper extension
housing
Screw
Plastic Protector
Recommended for use with the Childcare Assisted Auto Close Gate Extension (sold separately).

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate...
1
2
The gate must be installed in a structurally sound
opening.
Never install between two railings or two stair posts.
Ensure mounting surface (wall,door frame, etc) is
strong, rigid and is smooth, clean and grease free.
If mounting onto brick,plaster board or other surfaces,
an optional gate installation kit,wooden board
mounted to the surface or additional hardware may
be necessary to provide a solid,smooth surface.
Measure opening to determine if extensions are
needed.
Correct width will be reached by adjusting all 4 corner
spindles.
Each spindle adjusts individually and may be
extended to varying lengths (up to 45mm) to allow for
moulding,uneven walls etc.
This gate can be used in a closed doorway. Never use
gate at the top of the stairs.
1a.
1b.
1c.
2a.
2b.
2c.
2d.

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
A A
CC
B B
BB
A A
CC
B B
BB
A A
CC
B B
BB
A A
CC
B B
BB
3
4
5
Spindle attachment is different when using extensions
and when not using extensions.
Spindle housings are not used if square extension
tubes are required,If the housings have been inserted,
remove with a screwdriver.
If no extension/s are used,slide
top spindles (A) and bottom
spindles (C) into spindle
housing end (B).
Push assembly into gate
corners.
If using extension/s, insert square extension tubes (f)
into gate ends.
Connect extension bar (g) to one upper extension
housing (d) and one lower extension housing (e).
Push assembly over extension tubes.
There should be no metal showing from extension
tubes.
It may be necessary to apply pressure to tubes to
ensure they are fully inserted into gate ends.
Slide top spindles (a) and bottom spindles (c) into
extension tubes.
3a.
3b.
4a.
4b.
5a.
5b.
5c.
5d.
5e.
5f.

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
6
7
8
9
10
Centre the gate in opening with bottom rail resting on
oor.
Gaps on each side should be equal.
Pull out the two bottom spindles (c) until they touch
the mounting surface and rest on top of oor
moulding (if applicable).
Tighten handwheels TOWARD GATE FRAME as tightly
as possible.
Each spindle adjusts individually and may be
extended to varying lengths to allow for moulding,
uneven walls,etc.
Close walk through door so it is aligned directly above
bottom gate rail.
Pull out top spindle (a) on the hinge side (h) until it
touches mounting surface.
Tighten handwheel TOWARD GATE FRAME.
Pull out top spindle (a) on handle side until it touches
mounting surface and tighten handwheel TOWARD
GATE FRAME.
Take turns tightening both top spindles until tension is
reached and the distance between the handle and
frame is 0.80mm.
To open gate: Pull back release button (i) on handle.
Lift gate door and swing open.
6a.
6b.
7a.
7b.
7c.
8a.
8b.
8c.
9a.
9b.
10a.
IMPORTANT: The gate must be level and straight up and down,otherwise the gate’s
self closing door will not function properly.
.80mm

ASSEMBLY / OPERATING INSTRUCTIONS
To install Safety Gate (continued)...
To use the Hold Open Feature...
11
1
To close gate: The walk through door will automatically
close by itself and the lock will re-engage.
Test the gate door from both directions.
If the gate is lined up properly the door will close
automatically, conrmed with an audible ‘click’.
If it closes from one side and not the other,it means
that the gate is tilted towards the side that it will NOT
close from.
When this is the case,loosen the top spindles and
straighten the gate in the doorway; tighten the
spindles and test again.
Continue to test until gate door automatically closes
from both sides.
Now the gate is in proper working order.
By opening the door to a 90 degree or greater angle, it
will stay open until it is pushed closed.
11a.
1a.

HOW TO CARE FOR YOUR CHILDCARE SAFETY GATE
Cleaning
Maintenance
This product has been designed and developed with safety,comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference. To ensure the long-lasting use of your gate, wipe
down with a damp cloth and use a mild soap solution if necessary.
Do not use abrasive cleaners. Always store product in a clean dry
place.
Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required.To maintain the safety of your
safety gate, seek prompt repairs for bent, torn, worn or broken parts.
Use only those parts and accessories approved by CNP Brands.
If you have any difculties in assembling the safety gate, please
contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand
contact Wainhouse Distribution on 0800 567 5000.

ABOUT US
About CNP Brands
Currently,CNP Brands boasts one of the most diverse brand portfolios
with a combination of company owned brands and distribution
agreements.These include distribution lines for 4moms,Brica,Cybex,
Eveno, Good Baby, Lascal, Maclaren, Motorola, Munchkin, OiOi &
Summer Infant.
Our own brands, including Childcare, have gone from strength to
strength in recent years. Childcare, and our premium brand bebe
care, demonstrate our commitment to quality and continuing
investment in product development.

Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut,VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [email protected].nz