ChildLife PG134 User manual

817 Maxwell Avenue • Evansville, IN 47711 • 1-800-GO-SWING • www.escaladesports.com • ©2015 Escalade Sports
REQUIRED TOOLS:
(2) 3/4" Sockets and Ratchets
3/4" Wrench
11/16” Wrench
1/2" Socket and Wrench
9/16" Socket and Wrench
5/16" Allen Wrench
Drill with Phillips Driver Bit
3/8" Drill Bit
1/8" Drill Bit
Hammer
Tape Measure
Utility Knife
2 ft level
Carpenters Square
6' to 8' Step Ladder
RECOMMENDED TOOLS:
Impact Driver
(2) Saw Horses
(4) Bar Clamps or C-Clamps
PG-MA-0034-01
Lion’s Den (PG134)
Assembly Instructions

Here are some maintenance tips required to insure safe enjoyment of your equipment for years to come.
A. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed,
swing seats, chains, ladders, slides, rope and wood components for signs of deterioration and replace if necessary.
B. On a yearly basis, we recommend that you coat your playset with a sealant or preservative. You may also want to spot
sand any areas prior to sealing. Be sure that the sealant you select is non-toxic and child safe.
C. Do not use line trimmers or “weed eaters” around your play equipment. The line will remove both stain and wood
from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited
warranty.
D. Remove plastic swing seats and take indoors or do not use when the temperature drops below 0º F.
Welcome to our family of ready-to-build backyard play equipment. CHILDLIFE playsets are designed with ease of
assembly in mind and we provide these step-by-step installation instructions.
After reading the information below, locate your structure site and carefully unpack parts. As you unpack your playset,
keep the parts identification sheet handy and become familiar with each part before beginning assembly. Remember that
a little extra time spent familiarizing yourself with the parts and instructions before you begin will help you avoid mistakes
and save you time later.
Choosing A Location For Your Playset
Do not install home playground equipment indoors,
or over concrete, asphalt, packed earth, grass, carpet
or any other hard surface. A fall onto a hard surface
can result in serious or fatal injury.
Responsible on-site adult supervision is one of the
most important contributions to children’s safety that
you can make. CHILDLIFE strongly recommends on-
site adult supervision of children of all ages. Safe
swinging and climbing skills need to be taught to
children, just like any other physical activity.
The weight limit for any single user on CHILDLIFE play
equipment is 200 pounds. Limit the number of users
to one on each swing. The tower portion of the play
system will accommodate four (4) additional users.
When the time comes to disassemble and dispose of
the play equipment, do so in such a way that no
hazards will exist at the time the equipment is
discarded.
If you have any questions about your playset, or are in need of replacement parts, call 1-800-GO-SWING.
Please keep these instructions for future reference.
Maintaining Your Playset
I N T R O D U C T I O N
2
When selecting your structure site, always keep the
child’s safety in mind. Here are some recommendations
to help you create a safe play area.
A. The playset should be located on level ground. The
stationary components such as ladders and slides are
REQUIRED to be a minimum of six feet from any structure
or obstruction such as a fence, garage, house, tree or
overhanging branches, electrical wires or clotheslines.
Any swinging equipment is also to be a REQUIRED
minimum distance twice the height of the swing beam
away from these obstructions or structures as well. We
also recommend that you do not install your playset
near a lake, river, swimming pool or other water hazard.
B. The U.S. Consumer Product Safety Commission (CPSC)
recommends that you install and maintain a resilient
surface under your play equipment. The CPSC’s
Consumer Information Sheet for Playground Surfacing
Materials at the end of this manual. A resilient surface,
should be installed after the equipment has been
completely assembled according to these instructions.
The equipment must rest on solid ground. Please note
that this product has a maximum fall height of 8’.

S A F E T Y I N S T R U C T I O N S
In Addition, Adults Must:
• Not to walk close to, in front of, behind, or between
moving items.
• Not to twist the swing ropes, or loop them over the
top support bar, since this may reduce the strength
of the rope.
• Not to swing empty swing seats.
• Not to swing sideways into the path of adjacent
swings.
• Not to use the equipment in a manner other than
that for which it is intended.
• Not to get off the equipment while it is
in motion.
• Not to jump off the tower.
• Not to climb or swing when they are wet or when the
equipment is wet.
• Not to stand in the swing seats.
• Not to ride or leave bicycles or other toys in the
swing area.
• Not to use hammers, saws, nails, or wrenches on
the equipment.
• Not to swing so high that chains become slack, or
above the height of the swing support.
• Not to jump on a slide.
• Not to climb on top of the swing support.
• Not to attach to the playground equipment any item
that is not specifically designed for use with the
equipment, such as (but not limited to) jump ropes,
clotheslines, pet leashes, cables, and chains. These
may become strangulation hazards.
• To sit in the center of the swings with their full.
weight on the seats.
• To hold on to swings and climbers with.
both hands.
• To slide feet first, never head first..
• To watch for other children while swinging or playing.
near the equipment.
• Limit climbing and swinging heights to each child’s
ability.
• Verify that suspended climbing ropes are secured at
both ends.
• Verify that suspended climbing ropes cannot be
looped back on themselves.
• Dress children appropriately for play. Use well-fitting
shoes that do not have slippery soles.
Avoid ponchos, scarves, hoods, loose-fitting clothing,
neckties, and any clothing with a drawstring. Serious
injury could result should any part of the children’s
clothing become entangled in the equipment.
• Do not allow children to play wearing helmets.
• Remember that children are inventive. When they
develop games that are unsafe, be alert and change
the rules.
Teach Children:
3

PARTS LIST
4
PART NUMBER DESCRIPTION QTY.
1 84" ROCK WALL SIDE 2
20 73 7/8" MAIN BEAM 4
3 84" LADDER SIDE (RIGHT) 1
4 84" LADDER SIDE LEFT 1
5 94" HORIZONTAL ROOF SUPPORT 2
6 34 1/4" CORNER POST 12
7 80 1/4" CENTER ROOF SUPPORT 2
8 46 1/4" TOP HORIZONTAL ROOF SUPPORT 1
9 52 7/8" SIDE HORIZONTAL ROOF SUPPORT 2
10 66 1/4" BASE 1
11 90" BASE LADDER 1
12 14" 45 DEGREE ANGLE BRACE RIGHT 2
13 14" 45 DEGREE ANGLE BRACE LEFT 2
14 83 3/8" ROPE LADDER ARM 1
15 LADDER ROPE 3
16 24" ROPE LADDER RUNG 6
17 41 3/8" CORNER POST 4
18 66" LADDER SIDE CENTER 1
19 21 3/8" LADDER RUNG 5
21 86 7/8" ACCESSORY ARM 1
22 46" LONG 2"X6" DECK BOARD 6
23 46" LONG 2"x4" DECK BOARD 2
24 39 3/8" SHORT 2"x4" DECK BOARD 4
25 39 3/8" SHORT 2"x6" DECK BOARD 2
26 56 3/4" DECK FRAME 1
27 70" DECK BACKBOARD 1
28 30" DECK FRAME HALF 1
29 63 7/8" CLIMBING WALL BACKBOARD 1
30 SMALL HANDLE 6
31 LONG HANDLE 3
32 SHIPS WHEEL 1
33 TELESCOPE 1
34
35
#8 X 1.25" ROUND HEAD SCREW 18
36
CLIMBING ROPE 1
37
LADDER BRACKET 2
38
20" STEP
4
39
VINYL ROOF 1
PG-44-0070
PG-26-0005
PG-44-0067
PG-44-0069
PG-44-0072
PG-24-0066
PG-24-0067
PG-24-0022
PG-24-0023
PG-44-0027
PG-44-0022
PG-44-0015R
PG-44-0015L
PG-44-0023
PG-AC-0012
PG-24-0013
PG-44-0071
PG-44-0068
PG-ST-0003
PG-44-0017
PG-26-0008
PG-24-0015
PG-24-0014
PG-26-0007
PG-24-0021
PG-24-0017
PG-24-0024
PG-24-0065
PG-AC-0002
PG-AC-0015
PG-AC-0005
PG-AC-0004
PG-HW-S002
PG-AC-0006
PG-HW-M010
PG-26-0004
PG-AC-0013
PG-HW-S004 #8X2" FLAT HEAD WOOD SCREW 198
NO.
ITEM
40 PG-HW-W003 5/16" FLAT WASHER 48
41 PG-HW-L005 5/16 x 4" Hex Lag Screw 8
42 PG-HW-L006 5/16" x 5" LAG SCREW 21
43 #8X4" FLAT HEAD WOOD SCREW 16
44 5/16" x 3" LAG SCREW 5
45 3/8" FLAT WASHER 74
PG-HW-S010
PG-HW-L004
PG-HW-W004
46 3/8"-16 X 6" HEX BOLT 12 PG-HW-B006

PARTS LIST
5
PART NUMBER
DESCRIPTION QTY.
NO.
ITEM
47 3/8" NYLON LOCKNUT 36
48 3/8"-16 ACORN NUT 15
65
136" 3 POSITION HEAD BEAM 1
66 ANGLE BRACKET 2
67 112" A-FRAME LEG 2
68 65" A-FRAME CROSSBRACE 1
69 U-JOINT CENTER SPACE BLOCK 1
70 U-JOINT OUTSIDE 2
71 DUCTILE SWING HANGER 8
72 TRIANGLE SWING BEAM PLATE 1
73 1/2"-13 ACORN NUT 2
74 1/2" FLAT WASHER 6
75 1/2"-13 x 10" HEX BOLT 1
76 1/2" NYLON LOCKNUT 2
77 1/2"-13 x 11.5" HEX BOLT 1
78 3/8"-16 x 9" HEX BOLT 1
79 5/16”-16 X 2.5” CARRIAGE BOLT 2
80
CHAINS / EYE BOLTS / SWIVEL
1
81 5/16” STANDARD NUT 2
82 5/16” LOCK WASHER 2
83 5/16”-16 ACORN NUT 2
84 #8 X 2.5” WOOD SCREW 12
85 3/8” STANDARD WASHER 1
86
PG-HW-N001
PG-HW-N003
PG-46-0004
PG-HW-M003
PG-44-0073
PG-44-0005
PG-44-0008
PG-44-0007
PG-HW-M002
PG-HW-M004
PG-HW-N005
PG-HW-W005
PG-HW-B004
PG-HW-N004
PG-HW-B005
PG-HW-B003
PG-HW-B007
PG-HW-M009
PG-HW-N006
PG-HW-W006
PG-HW-N007
PG-HW-S009
PG-HW-W007
PG-AC-0017 TIRE 1
87 PG-HW-B009 3/8” -16 X 4.5” HEX BOLT 4
50 3/8"-16 x 6.5" HEX BOLT 20
51 #8 X 1 Round Head Screw 8
52 5/16" X 2.5" LAG SCREW 12
54 LONG DECK BOARD WITH HOLE 2
55 #10 FLAT WASHER 42
56 #10 X 1" ROUND HEAD SCREW 28
57 46" CLIMBING WALL BOARD CENTER 4
58 46" CLIMBING WALL BOARD SINGLE 5
59 46" CLIMBING WALL BOARD DOUBLE 2
60 46" CLIMBING WALL BOARD ROPE 1
61 CLIMBING ROCK 14
62
3/8"-16 X 1/2" T-NUT 14
63
3/8- 16 x 2" Socket Head Screw 14
PG-HW-B001
PG-HW-S007
PG-HW-L003
PG-26-0019
PG-HW-W001
PG-HW-S001
PG-26-0011
PG-26-013
PG-26-0009
PG-26-0010
PG-AC-0003
PG-HW-N002
PG-HW-B010
53 1/4" FLAT WASHER 1 PG-HW-W002
64
#10 X 2” Self Tapping Screw 10 PG-HW-S006
88 1
89
TRAPEZE SET
BELT SWING-GREEN 1
90 CHILDLIFE NAME PLATE 1
91 SPRING CLIP 9
92 TIRE SWING SWIVEL 1
BELT SWING-YELLOW 2
PG-AC-0010
PG-AC-0008
PG-AC-0011
PG-HW-M008
PG-HW-M014
PG-AC-0009
104” 2 POSITION HEAD BEAM 1 PG-46-0005
93 20”-45° ANGLE BRACKET (LEFT) 1
94 20”-45° ANGLE BRACKET (RIGHT) 1
PG-4X4-020-BRL
PG-4X4-020-BRR

6
LADDER SIDE RIGHT
PG-44-0067
#03
(1)
ROCKWALL SIDE
PG-44-0070
#01
(2)
#01
(2)
LADDER SIDE LEFT
PG-44-0069
#04
(1)
HORIZONTAL ROOF SUPPORT
PG-44-0072
#05
(2)
CORNER POST
PG-24-0066
#06
(12) CENTER ROOF SUPPORT
PG-24-0067
#07
(2)
TOP HORIZONTAL ROOF SUPPORT
PG-24-0022
#08
(1)
BASE
PG-44-0027
#10
(1)
BASE LADDER
PG-44-0022
#11
(1)
SIDE HORIZONTAL ROOF SUPPORT
PG-24-0023
#09
(2)
45 DEGREE ANGLE BRACE RIGHT
PG-44-0015R
#12
(2)
STANDARD PARTS

7
45 DEGREE ANGLE BRACE LEFT
PG-44-0015L
#13
(2)
ROPE LADDER ARM
PG-44-0023
#14
(1) PG-AC-0012
LADDER ROPE
#15
(3)
ROPE LADDER RUNG
PG-24-0013
#16
(6)
CORNER POST
PG-44-0071
#17
(4)
#18
(1)
LADDER SIDE CENTER
PG-44-0068
LADDER RUNG
PG-ST-0003
#19
(5)
MAIN BEAM
PG-26-0005
#20
(4)
#21
(1)
ACCESSORY ARM
PG-44-0017
#22
(6)
LONG 2” X 6” DECK BOARD
PG-26-0008
#23
(2)
LONG 2”x4” DECK BOARD
PG-24-0015 SHORT 2”x4” DECK BOARD
PG-24-0014
#24
(4)
SHORT 2”x6” DECK BOARD
PG-26-0007
#25
(2)
STANDARD PARTS
#54
(2)
LONG 4” X 6” DECK BOARD W/HOLE
PG-26-0019

8
DECK FRAME
PG-24-0021
#26
(1)
DECK FRAME HALF
PG-24-0024
#28
(1)
SMALL HANDLE
PG-AC-0002
#30
(6)
CLIMBING WALL BACKBOARD
PG-24-0065
#29
(1)
PG-24-0017
DECK BACKBOARD
(1)
#27
LONG HANDLE
PG-AC-0015
#31
(3)
PG-AC-0005
SHIPS WHEEL
(1)
#32
TELESCOPE
PG-AC-0004
(1)
#33
CLIMBING ROPE
PG-AC-0006
(1)
#35
LADDER BRACKET
PG-HW-M010
(2)
#36
PG-26-0004
STEP
#37
(4)
VINYL ROOF
#38
PG-AC-0013
(1)
CLIMBING WALL BOARD CENTER
PG-26-0011
#57
(4)
CLIMBING WALL BOARD - SINGLE
PG-26-013
#58
(5)
PG-26-0009
CLIMBING WALL BOARD - DOUBLE
#59
(2) PG-26-0010
CLIMBING WALL BOARD - ROPE
#60
(1)
PG-AC-0003
CLIMBING ROCK
#61
(14)
STANDARD PARTS
20" - 45 Degree Angle Brace Left
PG-4X4-020-BRL
20" - 45 Degree Angle Brace Right
PG-4X4-020-BRR

9
STANDARD PARTS
PG-44-0073
118” A-FRAME LEG
#67
(2)
PG-44-0005
65” A-FRAME CROSSBRACE
#68
(1)
PG-46-0004
136” 3 POSITION HEAD BEAM
#65
(1)
PG-44-0007
U-JOINT OUTSIIDE
#70
(2)
PG-44-0008
U-JOINT CENTER SPACE BLOCK
#69
(1)
PG-HW-M003
ANGLE BRACKET
#66
(2) PG-HW-M004
TRIANGLE SWING BEAM PLATE
#72
(1)
PG-HW-M002
DUCTILE SWING HANGER
#71
(8)
PG-HW-M009
CHAINS / EYE BOLTS
#80
(1)
PG-AC-0017
TIRE
#86
(1)
PG-AC-0011
NAME PLATE
#90
(1)
#89
Belt swing green w/chain
PG-AC-0008 (1)
Belt swing Yellow w/chain
PG-AC-0009
(2)
#88
TRAPEZE SET
PG-AC-0010
(1)
#92
TIRE SWING SWIVEL
PG-HW-M014
(1)
#91
SPRING CLIP
PG-HW-M008
(9)
OR
#65
104” 2 POSITION
HEADBEAM
PG-46-0005
(1)

10
#50
3/8”-16 x 6.5” HEX BOLT
PG-HW-B001
0
1
2
3
4
5
6
7
8
9
Measurement taken from bottom of bolt head to the bottom of bolt
(18)
#49
1/4"” x 4.5" LAG SCREW
PG-HW-L002
(1)
#44
5/16” x 3" LAG SCREW
PG-HW-L004
(5)
PG-HW-B006
3/8”-16 x 6” HEX BOLT
(12)
5/16” x 4" LAG SCREW
PG-HW-L005
#41
5/16” x 5" LAG SCREW
PG-HW-L006
(17)
#42
#46
10
(8)
#79
5/16”-16 X 2.5” CARRIAGE BOLT
PG-HW-B007
(2)
#52
5/16” x 2.5" LAG SCREW
PG-HW-L003
(12)
PG-HW-S006
#64
#10 X 2” Self Tapping Screw
(10)
3/8" X 4" Lag Screw
PG-HW-L013
#95
(8)

11
0
1
2
3
4
5
6
7
8
9
Measurement taken from bottom of bolt head to the bottom of bolt
PG-HW-B005
1/2”-13 X 11.5” HEX BOLT
#77
(1)
PG-HW-B004
1/2”-13 X 10” HEX BOLT
#75
(1)
PG-HW-B003
3/8”-16 X 9” HEX BOLT
#78
(1)
PG-HW-N004
#76
½” NYLON LOCK NUT
(2)
PG-HW-N005
#73
1/2”-13 ACORN NUT
(2)
PG-HW-W005
#74
½” FLAT WASHER
(6)
11
PG-HW-B009
3/8”-16 X 4.5” HEX BOLT
#87
(4)
#93
PG-HW-B011
3/8 X 6.5” Carriage Bolt
(2)
3/8” LOCK WASHER
(2)
PG-HW-W007
#94
#95
PG-HW-N008
3/8” STANDARD NUT
(2)

12
0
1
2
3
4
5
6
7
8
9
#62
3/8"-16 X 1/2" T-NUT
PG-HW-N002
(14)
#48
3/8”-16 Acorn Nut
PG-HW-N003
(15)
#45
3/8" Flat Washer
PG-HW-W004
(72)
#40
5/16" Flat Washer
PG-HW-W003
(48)
#34
#8 X 1.25” Round Head Screw
PG-HW-S002
(18)
#47
3/8” Nylon Locknut
PG-HW-N001
(36)
#63
3/8”- 16 x 2" Socket Head Screw
PG-HW-B010
(14)
#43
#8X4” PH FLAT HD WDSCR
PG-HW-S010
(16)
#39
#8X2” PH FLAT HD WDSCR
PG-HW-S004
(198)
#55
#10 Flat Washer
PG-HW-W001
(24)
#53
1/4" Flat Washer
PG-HW-W002
(18)
#8 X 1” ROUND HEAD SCREW
(8)
12
#51
PG-HW-W006
5/16” STANDARD NUT
PG-HW-N006
#81
(2)
#82
(2)
5/16” LOCK WASHER
#10 X 1” ROUND HEAD SCREW
PG-HW-S001
#56
(28)
#83
5/16”-16 Acorn Nut
PG-HW-N007
(2)
3/8” STANDARD WASHER
#85
PG-HW-W007
(1)
#84
#8X2.5” PH FLAT HD WDSCR
PG-HW-S009
(6)
PG-HW-S007

13
LADDER ASSEMBLY
PARTS NEEDED
#04 84” LADDER SIDE LEFT (1)
#18 64” LADDER SIDE CENTER (1)
#37 WOOD LADDER THREAD (4)
1. Attach Ladder Threads #37 to Ladder Side #18 and #04
Using Wood Screws #43.
2. There should be 7/8" overhang on both sides
of item #18 and item #04. See Detail 1.
HARDWARE NEEDED
#43 #8x4” FLAT HEAD WOOD SCREW (16)
#18
7/8”
7/8”
DETAIL 1
Angle side faces up
Holes face up

14
#04
#12
#13
#11
#42
#40
10"
2"
FLUSH
#04
3. Attach item #11 to the backside of ladder assembly
approximatley 2" from bottom of items #01, #04, and #18.
extend 10" past item #04.
4. Attach items #12 and #13 to items #03 and #04 with angled
surface flat against items #04 and #03. Attach items #11, #12,
and #13 using hardware items #40 and #44.
PIPE RUNG
ASSEMBLY
HARDWARE NEEDED
#40 5/16” FLAT WASHER (7)
#41 5/16” X 4” LAG SCREW (2)
#42 5/16” X 5” LAG SCREW (5)
#64 #10 X 2” SELF TAPPING SCREW (10)
using hardware items #40 and #44. Left end of item #11 should
#41
#42
#40
PARTS NEEDED
#03 84” LADDER SIDE LEFT (1)
#12 45 DEGREE ANGLE BRACE (RIGHT) (1)
#13 45 DEGREE ANGLE BRACE (LEFT) (1)
#19 21 3/8” LADDER RUNG (5)
1. Slide Ladder Rungs #19 into Ladder center #18
and Ladder Side #03 onto rungs #19 as shown.
24 5/8”
2.
Angle sides face up
Secure Ladder Rungs #19 with Self Tapping Screws
#64 as shown. The ladder should have a width of
24 5/8” as shown.
FLIP STEP 2 ASSEMBLY OVER AND CONTINUE WITH STEP 3.

15
1. Place all Climbing Wall Boards items #57, #58, #59, and
into pre-drilled holes as shown. Use a hammer or rubber
#58
#59
#62
ROCK WALL BOARD
HARDWARE INSTALLATION
PARTS NEEDED
#57 CLIMBING WALL BOARD (CENTER) (4)
#58 CLIMBING WALL BOARD (SINGLE) (5)
#59 CLIMBING WALL BOARD (DOUBLE) (2)
#60 CLIMBING WALL BOARD (ROPE) (1)
HARDWARE NEEDED
#62 3/8”-16 X 1/2” T-NUT (14)
12
ROCK WALL
ASSEMBLY
#60 on a flat surface and install hardware items #63
mallet to gently tap hardware into place as needed.
HARDWARE NEEDED
#39 #8 X 2” FLAT HEAD WOOD SCREW (66)
PARTS NEEDED
#01 LADDER SIDE (2)
#29 CLIMBING WALL BACKBOARD (1)
#57 CLIMBING WALL BOARD (CENTER) (4)
#58 CLIMBING WALL BOARD (SINGLE) (5)
#59 CLIMBING WALL BOARD (DOUBLE) (2)
#60 CLIMBING WALL BOARD (ROPE) (1)
46”
22 1/2”
#58
#58
#57
#59
#57
#58
#58
#57
#59
#58
#60
#01
#29
1. Lay items #01 as shown, measuring 46” from outside face
2. Measure 22 1/2" down from angled edge of items #01, arrange items,
#57, #59, and #60 in order shown. Be sure that T-NUT #62 is facing #58,
down when arranging Climbing Wall Boards.
(MAKE SURE ASSEMBLY IS SQUARE)
3. Attach items #29, #57, #58, #59, and #60 using hardware item #39.
(MAKE SURE ITEM #29 IS FLUSH WITH BOTTOM OF ITEM #60, AND CENTERED ON
PRE-DRILLED HOLES IN ITEMS #57, #58, #59, AND #60)
to outside face.
#39
START ON
THIS END
15

16
#12
#41
#40
#42
#40
#40
#42
#10
1. Turn Rock Wall Assembly face down and install item #10
2. Placing item #10, 2" up from bottom of items #01 AND #03 as shown in DETAIL VIEW.
3. Item #10 should extend out past the outside face of items #01and #03 approximately 10".
Attach item #10 to items #01 and #03 with hardware items #40 and #41.
4. Position items #12 and #13 as shown bottom edge of items #12 and #13 must be flush
with bottom face of item #10.
5. Attach items #12 and #13 with hardware items #40, #41, and #42.
ROCK WALL BASE
ASSEMBLY
HARDWARE NEEDED
#34 #8X1.25 ROUND HEAD SCREW (14)
#40 5/16” FLAT WASHER (6)
#41 5/16 X 4” LAG SCREW (2)
#42 5/16 X 5” LAG SCREW (4)
#55 #10 FLAT WASHER (14)
#63 #3/8-16 X 2” SOCKET HEAD SCREW (14)
PARTS NEEDED
#10 BASE (1)
#12 ANGLE BRACE (RIGHT) (1)
#13 ANGLE BRACE (LEFT) (1)
#61 CLIMBING ROCK (14)
2"
10"
#01
#13
#10
FLUSH
VIEW FROM BACKSIDE OF
ROCK WALL ASSEMBLY
#61
6. Attach items #61 using hardware #34, #55 and #63.
#63
#34
#55

17
CONFIRM THAT ITEMS #20, LADDER ASSEMBLY AND
ROCK CLIMBING WALL ASSEMBLY ARE ORIENTED AS SHOWN
1. On a flat surface arrange item #20, Ladder Assembly, and Rock Climbing Wall Assembly
(AS SHOWN).
2. Attach Assemblies to item #20 using hardware items #45, #46, #47, and #48.
#20
#20
LADDER ASSEMBLY
ROCK CLIMBING WALL ASSEMBLY
#46
#45
#45
#47
#48
HARDWARE SHOULD BE HAND TIGHTENED ONLY
LADDER ASSEMBLY - ROCK CLIMBING WALL
MAIN BEAM ASSEMBLY
PARTS NEEDED
ROCK CLIMBING WALL ASSEMBLY (1)
LADDER ASSEMBLY (1)
#20 MAIN BEAM (4)
HARDWARE NEEDED
#45 3/8” FLAT WASHER (8)
#46 3/8-16 X 6” HEX BOLT (4)
#47 3/8-16 NYLON LOCK NUT (4)
#48 3/8-16 ACORN NUT (4)
#20
#20
3. Tighten hardware only after Corner Post Installation is complete.

18
#20
#20
#20
#17
#17
#03
#20
#04
ROCK CLIMBING WALL ASSEMBLY
LADDER ASSEMBLY
2. GATHER ALL PARTS AND HARDWARE REQUIRED FOR THIS STEP BEFORE
NOTE:
1. TWO OR MORE PEOPLE WILL BE REQUIRED TO COMPLETE THIS STEP.
#52
#52
#40
#41
#40
#40
#47
#48
#45
#46
CARPENTERS SQUARE
NO GAPS
DETAIL 2
#20
#20 DETAIL 1
#04
FLUSH
.
1. Have one person pick up on the Ladder Assembly pieces so the
outside face of Ladder Legs are flush with the angled face of
item #20 (SEE DETAIL 1)
2. Place items #17 with countersunk holes facing one another, and
attach to items #20.
NOTE: USE A CARPENTERS SQUARE TO ENSURE CORNER UPRIGHTS
ARE SQUARE WITH ITEMS #20
3. Secure the Ladder Assembly by attaching items #03 and
#04 to items items #20, and #17. Using hardware items #40,
#45, #46, #47, #48, and #41. There should be minimal or no
gaps between items #17, #03, and #04.
As shown in (SEE DETAIL 2)
4. Repeat steps 1 through 3 for the Rock Climbing Wall Assembly.
CORNER POST
INSTALLATION
PARTS NEEDED
#17 CORNER POST (4)
HARDWARE NEEDED
#40 5/16” FLAT WASHER (12)
#45 3/8” FLAT WASHER (8)
#46 3/8-16 X 6” HEX BOLT (4)
#47 3/8” NYLON LOCKNUT (4)
#48 3/8-16 ACORN NUT (4)
#41 5/16” X 4” LAG SCREW (4)
#52 5/16” X 2.5” LAG SCREW (8)
3. TIGHTEN ALL HARDWARE AT THIS TIME.
PICKING UP ASSEMBLY.
COUNTER SINK ON INSIDE

19
#17
1. Attach item #05 to items #17 using hardware items #45, #47, #48 and #50 making
sure the countersunk holes in bottom of items #05 are facing down.
TOP JOIST
INSTALLATION
PARTS NEEDED
#05 HORIZONTAL ROOF SUPPORT (2)
HARDWARE NEEDED
#45 3/8” FLAT WASHER (8)
#47 3/8” NYLON LOCK NUT (4)
#48 3/8-16 ACORN NUT (4)
#50 3/8-16 x 6.5” HEX BOLT (4)
#05
#45
#50
#48
#47
#45
COUNTER SINK
FACING DOWN
#17
#17
#05
#17

20
1. Attach items #14 and #21 to items #05, using hardware
2. Using a Carpenter Square verify that items #17, #20,
and #05 are all square with each other.
#42
#40
#42
#40
#42
#40
#05 #05
#21
#20
#17
#20
PARTS NEEDED
#14 ROPE LADDER ARM (1)
#21 ACCESSORY ARM (1)
#71 DUCTILE SWING HANGER (2)
HARDWARE NEEDED
#42 5/16” X 5” LAG SCREW (4)
#40 5/16” FLAT WASHER (4)
#45 3/8” FLAT WASHER (8)
#47 3/8” NYLON LOCKNUT (4)
#87 3/8”-16 X 4.5” HEX BOLT (4)
ROPE LADDER / ACCESSORY ARM
INSTALLATION
CARPENTERS SQUARE
items #40 and #42.
#42
#40
3. Attach item #71 as shown using hardware items #45
#47, and #87
#87
#45
#47
#71
(SEE DETAIL 1)
DETAIL 1
#14
#45