Terra Bound Solutions Bedrock Instruction sheet

Bedrock Climber Installation Guideline
Age Group:
2-12 Years
Recommended Crew:
Minimum 1-2 People
Tools Required for Assembly:
T-30 TORX Bit
3/16” x 6” Drill Bit
Post Hole Digger / Shovel / Auger
Tape Measure
Level
High Speed 3/8” electric drill w/ clutch
Installation Time:
15 minutes – 30 minutes
Concrete Required:
1.1781 cu ft. per post
Note: Concrete must have a minimum rating of 2,500 psi and must be mixed per
manufacturers recommendation.
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 1

Bedrock Climber Installation Guideline
Standard Hardware
5/16” x 5” RSS
Stainless
5/16” x 4” RSS
Stainless
5/16” x 3-1/8”
RSS Stainless
5/16” x 2-1/2”
RSS Stainless
1/4” x 2-1/2”
RSS Stainless
#10 x 2-1/2”
R4 Stainless
NOT TO SCALE!
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 2

Bedrock Climber Installation Guideline
Bedrock Climber
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 3

Bedrock Climber Installation Guideline
Check off all items received, against the packing list. Notify your local sales representative
immediately ofany items that are missing or that maybe damaged.
Before beginning your playground installation, make sure that you have reviewed “Playtopia’s
Installation Guideline Manual”that was provided with your playground. If you did not receive
acopy ofthe manual please contact your local sales representative tohave a copy mailed or
emailed to you.
TERRABOUND SOLUTIONS IS NOT
RESPONSIBLE
FOR ITEMS DISCOVERED MISSING
AFTER 72 HOURS FROM TIME OF
DELIVERY.
Pre-Installation Check
PRE-DRILLING IS REQUIRED.ALL LOCATIONS WHERE
HARDWARE IS TO BE FA
STENED REQUIRES PRE-
DRILLING TOENSURE PROPER INSTALLATION AND
STRUCTURAL INTEGRITY. WE ARE NOT RESPONSIBLE
FOR INSTALLATION OR STRUCTURAL ISSUES THAT
ARISE FROM NOT PRE-DRILLING ATTACHMENTS.
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 4

Bedrock Climber Installation Guideline
This space intentionally left blank.
Bedrock Climber Footer
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 5

Bedrock Climber Installation Guideline
Bedrock Climber Footer
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 6

Bedrock Climber Installation Guideline
Ensure that the top of the bedrock (A) is flush with the top of the deck platform or Filler
Block (B), pre drill through the pilot holes located in the Bedrock Climber support with a
3/16” bit and into the post, then fasten a total of (4) 5/16”x5-1/8” RSS SS Screws (2in each
corner) through the Bedrock Climber supports and into the post.
Bedrock Climber Assembly
A
B
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 7

Bedrock Climber Installation Guideline
Once Bedrock Climber is attached swing the 2x3
leg supports down and into the footer locations as
shown on page 4.
Ensure that the 2x3 legs are level and at a 90
degree angle to the base of the Bedrock Climber
before setting in concrete. Reference footer
diagram on page 5.
This space intentionally left blank.
Bedrock Climber Assembly Contd.
DATE: 4/23/2014 BEDROCK CLIMBER INSTALLATION GUIDELINES
Page 8