Quick Start Guide
lnterface
General lntroduction
This quick start guide is designed to be a reference for cube
net\ rork camera operation, including open-package inspection,
camera construction introduction, camera installation quick
configure tool, web operation, FAQ and appendix.
Symbol definition
Below symbols maybe show in this quick guide, the definition
is as follows :
lndicates a high degree of risk
which, if not avoided, will result in
death or serious injury.
lndicates a medium or low level of
risk which, if not avoided, could
result in minor or moderate injury.
lndicates a potentially hazardous
situation, if not avoided, could
result in equipment damage, data
loss, performance degradation, or
unexpected results.
ndicates that may help you solve a
problem or save you time.
lndicates the text of the additional
information to emphasize or
The followings are the instructions of proper use of the
product as well as to prevent danger, to prevent damage of
property, etc. Before using the equipment,flease read lhis
manual thoroughly and during use please stricfly adhered to,
after reading please keep this manual.
I mportant Safety Instructions
utions
1.1 Power Requirements
.Please comply with all local electrical safety standards stricfly
w-he_n us9 or install this product. Please use the power with SELV
(S^afety Extra Low Voltage) standard. And supply the power with
DC12V in accordance with IEC6O9SO-1 line with Limited power
Source (limited supply).
lnstalling a readily accessible disconnect device when install
wiring, just for emergency poweroff when necessary.
Before using the camera, please check the poweisupply is
correct or not.
Please protect the power cord from belng walked on or pinched,
particularly at plugs, power outlets and the point where they exit
from the apparatus.
1.2 Environmental requirements
- Please avoid aligning the light (such as lighting, sunlight, etc.)
focu.sing, otherwise easily lead to too bright or putt tignt [tfris is nbt
for the d,evice bug), and it will also reducejbe lifetimE of ihe image
sensor CCD (or CMOS).
, Please transport, use and store this device in the allowed range
of humidity and temperature. Do not put the device in the
environment of humid, dusty, extreme heat, extreme cold, strong
electromagnetic radiation or unstable lighting conditions and
other places.
Please do not let the water and any other liquid inflow into the
device, which may damage the internal components.
To prevent heat accumulation, please do not block air
circulation arqund the device.
Please prevent stress, violent vibration, immersion and other
damage from the product during the transportation, storage and
installation process.
When transporting the camera, need to be re-packaged with
the factory packaging, or with packaging material of equal quality,
Suggest with lighting protection devices when use in order to
make lighlning protection better.
Grounding hole on the product suggest to be grounded, for
further improving the reliability of the equipment-
1.3 Operation and maintenance requirements
Do nol disassemble the camera, for there are no user-
serviceable parts in the device.
Please do not touch the image sensor CCD (or CMOS) directly.
Hair dryer available to clear the dust or dirt on the surface of the
lens. lf cleaning is necessary, place a dry cloth lightly moistened
with alcohol, and wipe it gently.
Clean the body with a soft, dry cloth. ln case the dirt is difficult
to remove, you should use a clean, soft cloth dipped with smalt
amount of neutral detergent to wipe gently, and then dry.
Do not use volatile solvents, such as alcohol, benzene or
thinners, or with strong and abrasive cleaners. Otherwise it will
damage the surface coating or reduce the camera's performance.
ing
lnstallation and maintenance of this product should be
operated by specific operation, do not conduct their own
demolition and maintenance, and please Only use manufacturer's
prescribed attachments / accessories.
CCD (or CMOS) may be subject to the damage of the laser
beam, so in the use of a laser beam device, please keep the
surface of image sensor from the laser beam radiation.
Special Statement
Please refer to the practical production, and the manual is just
for your reference.
