Ciays TZEDS1 User manual

Model: TZEDS1/TZEDS1B1/TZEDS1N
Electric Standing Desk
Instruction Manual (A)
Thank you for choosing this product! We strive to provide you with the best
quality products and services in the industry. Should you have any issues,
please don't hesitate to contact us
Technical Support:
877-546-8648 Mon-Fri 8am - 8pm(CST)
Other Info: [email protected]

Power Input
110V-240V
Max.Speed
25 mm/s
Motion Noise
＜55dB
Load Capacity
176 lbs / 80 kg
RATED
Specification
Bolt
M6×35 mm
A (x8)
Bolt
M8×47 mm
C (x4)
3/16 in (5mm)
Large Allen Key
E (x1)
Foot
H (x4)
Right Table Leg
06 (x1)
Left Table Leg
05 (x1)
Crossbar
02 (x1)
Leg Base
07 (x2)
Supplied Parts and Hardware for Step 1
Bolt
M6×10 mm
B (x4)
5/64 in (2mm)
Small Allen Key
G (x1)
5/32 in (4mm)
Medium Allen Key
F (x1)
Rubber Pad
J (x10)
Side Plate
03 (x2)
Transmission Rod
04 (x1)
Supplied Parts and Hardware for Step 2
Desktop
01 (x2)
Supplied Parts and Hardware for Step 3
Supplied Parts for Step 4
Wall Plug Power
09 (x1)
Cable Clip
I (x2)
Vertical Range:
28.3 - 47.2 in (72-120cm)
01 02 03 04 05 06 09
Tabletop
Connector
08 (x3)
Controller
12 (x1)
Headset Hook
13 (x1)
Screw
M4x20mm
M (x2)
Screw
M5x16mm
D (x23)
Wooden Pin
N (x2)

Bolt
M5×12 mm
K (x6)
M20×1 mm
L (x4)
Step 1
Small Desktop
10 (x1)
Bracket
11 (x2)
Supplied Parts for Step 5
Assemble the Leg Bases and Crossbar
01 02 03 04 05 06 09
H
05
06
A
Large Allen Key
E
07 07
E
CLarge
Allen Key
Large
Allen Key
02
05
06
06
02

Step 2 Secure the Side Plates and Transmission Rod to
the Table Legs
01 02 03 04 05 06 09
1
2
Loosen the pre-assembled
coupling nut for adjusting
the length.
2-1
2-2
Insert the transmission rod on the left leg into
the hex hole and turn the transmission rod
anti-clockwise until the left leg goes to the
lowest position.
Coupling nut
Left Table Leg
Right Table Leg
Left Table Leg
Right Table Leg
Leg Base
Side Plate
03
B
Medium
Allen Key
F
05
03
04
04

01 02 03 04 05 06 09
3
4
5
Insert the other end of transmission
rod to the slot on the right leg (You
may rotate the rod slightly for better
installation).
Secure the transmission rod to the
slot by tightening the pre-assembled
set screw clockwise using the small
Allen key [G].
Small Allen Key
GG
Tighten the coupling nut.
⑪
J

01 02 03 04 05 06 09
Install Transmission Rod: Please fine-tune the transmission rod.
Step 1. Measure whether the height of
the two table legs are the same using a
measuring tape before installation.
How to Solve the Problem of Different Heights of Two Table Legs
Turn
anti-clockwise
Turn
anti-clockwise
Turn
anti-clockwise
Turn
anti-clockwise
①
②
Left Leg
Left Leg
Turn
clockwise
Turn
clockwise
①
②
Left LegLeft Leg
Step 2. If the height of left table leg is higher than the right
table leg, insert the transmission rod into the hexagonal hole
of the left leg, then rotate the transmission rod anti-clockwise
to fine-tune the left leg to make the left table leg as high as
the right table leg.
Step 3. If the height of the left table leg is lower than the
right table leg, insert the transmission rod into the hexagonal
hole of the left table leg and rotate the transmission rod
clockwise to fine-tune the left table leg to make the left table
leg as high as the right table leg.
Step 3 Secure the Desktop to the Stand
Soft Cloth
N
D
08
01
01
Phillips
Screwdriver
[Not Included]
Assemble the desktop.

01 02 03 04 05 06 09
Phillips
Screwdriver
[Not Included]
M
Can be mounted
in each side
Step 4 Connect the Cables
Right Table LegRight Table Leg
Soft Cloth
Built-in USB Port for charging
your device.
Duty Cycle: 10%,
2 min on/18 min off
12
09
09
Attach the leg assembly, controller and hook to
the desktop.
The pre-assembled
cable on the motor.
Self-supplied USB cable
13

Phillips
Screwdriver
[Not Included]
01 02 03 04 05 06 09 07
Step 5 Place the Monitor Stand on the Desktop
K
11
L
5-1
5-2
5-3
10
11

01 02 03 04 05 06 09 08
Press button, and the desk will move to the certain height that was
previously set for memory 1.
Press button, and the desk will move to the certain height that was
previously set for memory 2.
Press button, and the desk will move to the certain height that was
previously set for memory 3.
Short press [S] button, the display flashes. Press either of 1,2,3 memory keys
to save the height.
Reset

01 02 03 04 05 06 09

All of us do appreciate your product purchase. We hope that you are as
happy with your product as we are designing and manufacturing it for you.
We strive to provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to contact us
Technical Support:
877-546-8648 Mon-Fri 8am - 8pm(CST)
Other Info: [email protected]
Thank you again for
choosing this product!
860-00046-00 Rev00