Unfinished Furniture of Wilmington CU-167 User manual

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: DOUBLE JELLY CUPBOARD RTA
: CU-167

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Shelf panel
1
C
Bottom panel
1
D
Side panel
(L-R)
2
E
Upper Back
panel
(large)
1
F
Lower Back
panel
(small)
1
G
Door
(L-R)
2
H
Adjustable
shelf
2

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 4 -
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
HARDWARE LIST
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
12
2
Lock washer
(ɸ6.5 x 11mm)
12
3
Flat washer
(ɸ6.5 x 19mm)
17
4
Long screw
(M4 x 35mm)
1
5
Short screw
(M3.5 x 15mm)
28
6
Short pan head
screw
(M3.5 x 15mm)
15
7
Allen key
(M4 X 80mm)
1
8
Knob
2
9
Long pan head
screw
(M4 x 28mm)
2
10
Steel band
1
11
Shelf support
bracket
8

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 5 -
Attach side panels (D) to top (A), and shelves panel (B) and (C) with bolts (1), and washers (2) and (3)
as shown below. Tighten with Allen key (7).
Slide back panels (E) and (F) into grooves of side panels (D), then attach back panel (E) to top (A)
and back panel (F) to bottom panel (C) with pan head screws (6) as shown below. Tighten with a
screwdriver.
Attach back panels (E) and (F) to shelf panel (B) with pan head screws (6) and washers (3) as shown
below. Tighten with a screwdriver.
STEP 1
STEP 2

ITEM NO. : CU-167
REVISED MAR 24, 2016
Printed in Vietnam
- 6 -
Attach doors (G) to the unit with screws (5) as shown below. Tighten with a screwdriver.
Attach knobs (8) to doors (G) with pan head screws (9) as shown below. Tighten with a screwdriver.
Attach brackets (11) to side panels (D) as shown below. Then place the adjustable shelves (H) on the
brackets and attach with screws (5). Tighten with a screwdriver.
Attach steel band (10) to the unit with screws (5) and attach steel band to the wall with screw (4) as
shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
STEP 3
STEP 4