Wallbeds Australia AB-4b User manual

Important Safety Advice Sheet
PLEASE READ BEFORE YOU BEGIN:
•Please read and understand the instructions prior to assembly.
Incorrect installation of this product could possibly result in
personal injury or physical damage.
•WallBeds Australia recommends two people to safely assemble
and install the wall bed - It is not recommended you try to install
this bed on your own.
•The wall bed MUST be securely fastened to the wall prior to use.
Failure to do so will cause the bed to tip over & may cause
damage to the cabinet or serious personal injury.
•All additional cabinetry must be securely fasten to the Wall Bed
cabinet.
•Whilst these products are DIY it is recommended the wall bed be
installed by a qualified trades person if you are not comfortable
with the installation of this product.
WallBeds Australia is not responsible for any damages
or injuries incurred by incorrect installation of this
product.
1
©2019 WallBeds Australia

AB-4bAssembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number.
Prior to assembly, separate and group all matching panels numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units
have been built, as these will assist with assembly. Most of the stickers are placed
on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Back
Kick / Rail
Bottom Panel
Top Panel
AB-4b Drawer Cabinetry Panels
Drawer Front
Drawer Bottom
Drawer Back
2
Pull Out Drawer /Table Front
Pull Out Drawer Bottom
©2019 WallBeds Australia

AB-4b Drawer Hardware Parts
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Panel Bottom Panel Top Panel
Rail / Kick
Drw Back
Step 1– Inserting Drawer Cabinetry Hardware
3
Small Handle Drawer Clip
Pull Out Drawer / Table Runners
Handle Fixing Screw
Euro Screw Cam Lock
Cam Pin
Done Head Screw 28mm Wood Screw
Drawer Runners &
Metal Drawer Sides
Pull Out Drawer / Table Bottom
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
End Panel End Panel Drw Bot
Bottom Panel
Top Panel
NOTE: In the
Bottom Panel Insert
the cam pins on the
opposite side to the
Cam Lock.
Drawer Runners –
Attach the runners prior to assembling the cabinetry.
Line up the holes in the metal runner with the pre-drilled holes in the End Panel. Attach these
runners using the Euro screws. Do this for both End Panels - Refer to images 7 & 8 page 10
Drawer Clips –
NOTE: In the Top
Panel Insert the cam
pins on the same
side as the Cam
Lock
4
Drawer Front
Insert these into the drawer front ensuring the up & down arrows on the drawer clips are facing
the outside edge of the drawer panel.
Fix these into the drawer front by tapping them in gently with a hammer - Refer image 11 page 11
Pull Out Drawer / Table Runners –
Turn the runner over to view from the back. Detach the drawer slide from the main
sliding runner by pulling the clip as indicated by the arrow on the clip. Refer image
14 page 12. Line up the three holes in the metal runner with the pre-drilled holes in
the End Panel. Attach these runners using the Euro screws. Refer image 15 page
12. Repeat for the remaining End Panel.
DO NOT re-insert the drawer / table slide at this stage.
Pull Out Drawer /Table Front
©2019 WallBeds Australia

5
Step 2 Drawer Cabinet Assembly
Start the cabinet assembly by using either one of the cabinet End Panels.
Cabinet Back Panel - Ensuring the cam locks are facing away from the inside. Place the
cabinet back panel onto the side panel. Match up the cam locks with the cam pins.
Tighten the cam locks and cam pins together by using a Phillips head hand screwdriver.
Cabinet Bottom Panel - With the cam locks facing away from the inside of the cabinet
attach the bottom panel to the end panel and back panel. Refer image 12 page 11
Cabinet Top Panel - With the cam locks facing the inside of the cabinet attach the
bottom panel to the end panel and back panel. - Ensure the cam locks are facing the
inside of the cabinet. Refer image 11 page 12
Cabinet Kick / Rail Panel - With the cam locks facing to the back of the cabinet attach the
kick panel to the end panel.
Place the remaining end panel on top of the previously assembled panels. Ensuring the
cam pins are lined up with the cam locks. Tighten the cam pins to the cam locks.
Pull Out Drawer / Table - Attach the pullout drawer / table runners to the drawer / table
panel using the dome head screws. The holes for these are pre-drilled. Refer image 16
page 12
Pull Out Drawer / Table Front - Attach the Pull Out Drawer / Table to the front panel by
tightening the cam pins into the cam locks. Refer image 17 page 12
Drawer Assembly
Note – There are no pre-drilled guide holes on the underside of the drawer bottom
panel for the dome head screws. The dome head screws supplied do not require these
holes to be pre-drilled.
Drawer Back Panel to Drawer Bottom Panel - With the cam locks facing the back attach
the drawer bottom panel to the drawer back panel. Tighten cam locks to cam pins. Refer
image 2 page 9
Metal Drawer sides - Attach the metal drawer sides to the drawer bottom and drawer
back panels using the dome head screws. Refer image 1 page 9. Place assembled drawer
into the Cupboard Drawer cabinet.
Attaching Drawer Fronts – To ensure the drawer front is the correct way up. Place drawer
front on to the drawer clips -DO NOT PUSH DRAWER FRONT FULLY ONTO THE DRAWER
CLIPS.
Gently close the drawer ensuring the top edge of the drawer front will be level with the
top panel or drawer front above. If the drawer front is higher than the panel, remove it
from the drawer clips and turn the drawer front up the opposite way.
Double-check the drawer front is now level with the cabinet top panel.
Once the drawer front is the correct way up, push the drawer front into the metal sides
of the drawer until you hear the drawer click into place on both sides. Tighten the
screws on the outside of the drawer clips using a Phillips head hand screwdriver.
©2019 WallBeds Australia

AB-4b Bookcase Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Bottom Panel
Top Panel
AB-4b Bookcase Panels
Back Panel
6
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Cam Lock Cam Pin 28mm Wood Screw Shelf Pin
AB4b Bookcase Hardware Parts
Back Bottom Top
Rail
End End Bottom Top
NOTE: In the Top and
Bottom Panels Insert the
cam pins on the opposite
side to the Cam Lock.
Step 1– Inserting Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
7
©2019 WallBeds Australia

•Place the Drawer Cabinet unit next to the side of the Alpha Wallbed that it will be attached to.
Ensure the front edge of the drawers are flush with the front edge of the wall bed cabinet.
•Place the bookshelf unit on top of the drawer cabinet unit and line up the front of the bookcase
bottom panel with the front edge of the drawer.
•Check that the bookshelf end panel is also flush with the front edge of the wall bed cabinet end
panel.
You will need to pre-drill the 5mm screw holes.
When attaching the Pull Out Drawer / Table unit to the bookshelf.
•Remove the pull out drawer / & pre-drill a 5mm hole up through the top panel of the pullout
drawer unit into the bottom panel of the bookshelf. Do one towards the front and then one
towards the back of the unit. IMPORTANT - Use caution not to go all the way through to the
bottom panel of the bookcase. Attach together using the 28mm screws supplied.
•Using an existing shelf pin hole, fix the bookshelf to the side of the bed cabinet by using the
28mm wood screws supplied.
8
Step 2 - Bookcase Assembly
Start the Bookcase assembly by using either one of the Bookcase End Panels and fixing it to the
Back Panel. Ensure the cam locks on the Back Panel are not facing what will be the inside of the
Bookcase when built.
Back Panel - Place the Bookcase Back Panel onto the End Panel. Match up the cam locks with the
cam pins. Tighten the cam locks and cam pins together by using a Phillips head hand screwdriver.
Bottom & Bottom Panels - With the cam locks facing away from the inside of the Bookcase attach
the Bottom Panel to the End Panel and Back Panel. Repeat this process with the Top Panel.
Place the remaining End Panel on top of the previously assembled panels. Ensuring the cam pins
are lined up with the cam locks. Tighten the cam pins to the cam locks.
Tip: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure you
do this where the cam pins are. Failure to do so may result in damage to the End Panel.
Step 3– Fixing both Unitstogether and to the Alpha Wall Bed
Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on
any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
©2019 WallBeds Australia

9
Image 1 Image 2
Image 3 Image 4
©2019 WallBeds Australia

10
Image 5
Image 7
Image 8
Image 9
Image 10
Image 6
©2019 WallBeds Australia

11
Image 11 Image 12
Image 14
Image 13
©2019 WallBeds Australia

Image 14
Image 15
Image 16
Image 17
12
©2019 WallBeds Australia