Cineak Fortuny Original operating instructions

Fortuny - Incliner
Installation & Operation Guide
1 | Cineak - Luxury Seating
Fortuny incliner - installation & operating manual - 10/2009
1 Unpacking 2
2 Installation instratctions 3
3 Operating instructions 4
5 Maintenance 4

2 | Cineak - Luxury Seating
Fortuny incliner - installation & operating manual - 10/2009
1 Unpacking
1.1 Openingboxes
Products are packed in double carton boxes to provide extra
protection. Please carefully remove top box.
1.2 Unloading
Chairs are HEAVY - lift from both ends, requires at least 2
people to lift with caution.
Before unloading make sure you note which parts you take out
of the box. Reference numbers are located on the cover of the
box and match numbers on seating parts on next page (refer to
“1.3 Product ID references”).
- Lift chair out of the box (do not lift by footrest at front - do-
ing so can damage the mechanism - lift by frame or bottom of
armrest), keep bubble wrap around the chair until installation.
Make sure you don’t scratch the leather with any sharp items or
clothing (zipper/snaps/buttons).
- Look for power supply in box before discarding box/shipping
materials.
IMPORTANT: While unpacking chairs, please inspect all chairs/
parts/mechanisms for any possible damage that may have oc-
curred during shipping (seat, frame, wood). If damages are
noted please contact CINEAK immediately before completion of
install. Failure to do so may result in exclusion of warranty/any
and all claims.
1.3 Instalationreference
Each box will identify the contents included - with numbers
listed on the outside of the box
Each part of the row (armrest or seating part) has been assigned
a number. When unpacking parts please mark them with the
corresponding number to avoid confusion later. Each box will
have a label, identifying the part numbers included in the box.
Match the numbers indicated on the box with the numbers
listed on the seating parts in the drawing. This will allow for
proper installation
sample:
Box1: 1
Box2: 2 1 2 3 4
Box3: 3
Box4: 4
Box5: 5
Box6: 6
Box7: 7
5 6 7
TOOLS YOU WILL NEED:
(1) POWER SCREW DRIVER
- to secure backrest to seat frame
TOOLS YOU MAY NEED:
(1) CHANNEL LOCK Pliers
- for customizing the amount of recline/
incline of backrest.

3 | Cineak - Luxury Seating
Fortuny inclienr - installation & operating manual - 10/2009
2 Installation
B. Once the backrest is installed, securely engaged and screwed
to the seat base, attach the white elastics on the backrest ap to
the bottom of the seat frame (upside down silver posts).
C. Carefully lower the chair back onto the oor. Continue steps
A - C with all remaining chairs in the row.
ROW INSTALLATION
All chairs are connected to one another by lifting one chair/
armrest onto the locking bar attached to the next chair. When
connecting seats to armrests, connect the control wires from the
armrest to the corresponding driver box underneath each chair.
E. Lift each piece so it ts into the receiving lip (8) connected to
the other chair/arm. You may need to adjust the armrest forward/
backward until it lowers properly into position. Continue until
all chairs of row are connected.
POWER CONNECTIONS
Find the power cables, and plug into driver/control box located
at the rear of each chair frame. Connect other end of this cable
into the power supply/transformer and connect the power sup-
ply to the wall outlet. When connecting the transformer, ensure
the cable coming from the driver box under the chair is installed
into the transformer before connecting to the wall outlet.
TRANSFORMERPLACEMENT
Place transformers behind chair/row so there is proper
ventilation and they are clear of all moving parts. Do not place
transformers inside armrest cavity or underneath/chair.
We highly suggest that once the chairs are assembled, you look
underneath footrests from front to make sure all wires are run
properly so the chair nor any parts are sitting on top of any wires
and not rubbing/dragging on any moving parts. Take location of
wires into consideration if the row/seating needs to be moved.
CINEAK does not advise using surge protectors, extension cords
or splitters. CINEAK will not be responsible for damage or
hazard caused by improper placement of transformers or wires.
2.1 InstallationInstructions
Installation is recommended to be performed by 2 people and
is done by attaching armrests/seating pieces to adjacent seat
pieces - lifting each chair/arm onto the one beside it - no bolts!
ROWCONFIGURATION (see prev. page)
Start by placing all parts (seating/armrests) of each row next to
one another in the room so the numbers on the parts correspond
to the drawing in the Packing/Installation Reference (prev. page).
BACKREST INSTALLATION
The backrests will need to be installed rst, and it is suggested
that all backrests are attached prior to connecting any chairs in
row(s). If lumbar support has been ordered, see section 4 now.
A. Tilt the seat piece forward onto its armrests so you are able
to kneel behind it (1). While someone holds the backrest up
in place (2), lift the nish ap/piece on the backrest up (3) and
notice the securing wooden block and female “C” brackets on
each side (4). Align the two female “C” brackets on each side
of the backrest (4) to the corresponding male mounts on the
seat frame (5).
Once aligned, guide the backrest onto the male brackets on the
seat frame and push on the backrest until it touches the leather
of the seat. Make sure the backrest is pushed down completely
and the male/female connection is properly secured.
123
45
8

3.1 Controlbuttons
All motorized chairs are equipped with a control pad, which
controls the motors of the mechanism.
Controls build in on right hand side when sitting:
lift footrest lower backrest
close footrest bring up backrest
Controls build in on left hand side when sitting:
lower backrest lift footrest
bring up backrest close footrest
Lumbar support is also operated using these control pads:
increase support lift support
decrease support lower support
4 | Cineak - Luxury Seating
Fortuny incliner - installation & operating manual - 10/2009
3 Operating instructions
3.2 Batterypack
A seperate manual is available for these options.
3.3 Articulatingheadrest
All chairs have an articulating headrest, meaning the top of
the backrest can be moved manually to provide more support
when reclined. To do this pull the headrest with both hands
when sitting down. Push back to bring to original position.
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM
ADORED WORLDWIDE
HANDCRAFTED IN BELGIUM

5 | Cineak - Luxury Seating
Fortuny inclienr - installation & operating manual - 10/2009
5 Maintenance
5.1 Leathercare
Regularly dust your furniture with a soft cloth. Spills should be immediately blotted with a soft absorbent cloth whenever they oc-
cur, never rub. Ttreat your leather with a leather cleaner once every 6 months, or if needed.
For more information read the leather care.
5.2 Woodcare
Regularly dust your furniture with a soft cloth. Spills should be immediately blotted with a soft absorbent cloth whenever they oc-
cur, never rub.
5.3 Batteryoption
see separete manual
4.4 Lumbarsupport
Connect Lumbar support:
- If lumbar support has been ordered, when securing the backrest onto the seat, connect the small 5 pin wire from the underside of
the chair (9) to the driver box on the inside ap of the backrest (10). Make sure the lumbar support unit is properly in place and
has not moved/shifted during shipment - pull/push on the unit inside the backrest to make sure it is still mounted correctly. (Failure
to check this may void warranty).
4 Options
910