Burrow PROSPECT 5-DRAWER TALL DRESSER User manual

1
PROSPECT
5-DRAWER
TA LL D RES S ER
Assembly Instructions

22
Dresser parts
1x
Back wall
1x
Suport panel
5x
Drawer backs
10x
Drawer sides (L, R)
5x
Drawer fronts
5x
Drawer bases
4x
Legs
4x
Leg plates
8x
Thumbscrews
1x
Base panel
1x
Top panel
2x
Side walls (L, R)
Everything you need is
included
Thanks for bringing Burrow into your home.
We’ve worked hard to make your work
setting up your new furniture as easy as
possible. You’ll need an extra set of hands,
so be sure to grab a friend before you get
started. One big tip: assemble your dresser
as close to the final position as possible, to
minimize movement.

33
Anti-tip hardware
4x
Brackets
4x
Split pins
4x
Anchor pins
4x
Wood screws
4x
Wall claw anchors
4x
Wall claw screws
Feel free to contact [e-mail]
with any specific questions!
2x
Cables
1x
Screwdriver
To help you identify different but similar-
looking pieces, we’ve created a system
of removable label stickers. Pieces with a
green “A” sticker are on the right-hand side
of the piece, if you’re facing the front of it.
Pieces with the yellow “B” sticker are on the
left-hand side. The arrows indicate which
direction you should push pieces to secure
the clip connections.

4
1
Screw in two of the anti-tip brackets to the
underside of the top panel, using the wood
screws and the pilot holes as guides.
2
Put the eye at the end of an anti-tip cable in
between the bracket. Then, thread an anchor
pin though the bracket and eye. Secure the
assembly by fitting the straight side of the
split pin through the hole on the end of the
anchor pin.

5
3
Important: Take the back wall panel, and
lean it against the wall as close to the final
position of your dresser as possible. Flip to
the last page of this booklet, use the printed
ruler to measure above the holes on the back
4
Screw one leg onto each of the four leg
plates in a clockwise direction.
wall panel and make a mark where each
screw will go. Then, hammer in the wall claw
anchors at each of the marks, and use the
wall claw screws to attach brackets to
the wall.
__
__ __

6
5
Using two thumbscrews for each corner,
screw the leg and plate assemblies into the
four corners of the base panel, with the leg in
the outermost corner.
6
Flip the base panel so it’s resting on its
four legs. Attach the right wall to the base
panel by lining up the green (A) stickers,
with the “Top A” sticker at the top. There
are six clips: three on the edge of the base
panel, and three on the edge of the wall.
Align these clips, and press them together
until you hear a click.
x

7
7
While someone holds the right wall upright,
attach the left wall to the base panel by lining
up the yellow (B) stickers, with the “Top B”
sticker at the top. Just like the other wall,
there are six clips: three on the edge of
the base panel, and three on the edge of
the wall. Align these clips, and press them
together until you hear a click.
8
One person should stand at the front of the
dresser, holding both walls upright. The other
should attach the support panel to the left
and right walls, matching up the yellow (B)
and green (A) stickers. There are two holes
on the support panel; those should be at the
top. Push in the direction of the arrows on
the support panel.

8
9
Attach the top panel to the side walls
by aligning the yellow (B) and green (A)
stickers, and clicking down into place at all
10
Thread the anti-tip cables through the
holes in the support panel. Then, place the
back wall on the lip of the base panel while
you align the anti-tip hardware holes with
the ones on the support panel. Thread the
cables through the back wall, and then click
the back wall into place and push down to
lock it in.
connection points. Push or pull the top panel
towards the back of the dresser to lock
the clips.

9
11
Place the dresser in its final position,
and attach the anti-tip cables to their
counterparts on the wall, following the
instructions from Step 2.
12
Next, you’ll assemble the drawers. Gather
a drawer front, left and right drawer sides,
a drawer back, and a drawer base. Place a
drawer front face down on your work surface
(so the stickers are facing up), attach the right
side of the drawer by lining up the green
(A) stickers, making sure the groove at the
bottom creates a continual line between the
front and side.
Tip: The clips on the drawers are perma-
nent and cannot be undone once clicked
into place. Please carefully follow these
instructions.
Tip: If your oors are just a hair uneven, you
can unscrew each leg a little bit to raise that
section of the dresser to compensate.

10
13
Attach the left side of the drawer by lining
up the yellow (B) stickers, making sure the
groove at the bottom creates a continual line
between the front and side.
14
Slide the base into the grooves on the
sides and front of the drawer, making sure
the side with the sticker will be on the
bottom of the drawer.

11
1 2 3
15
Finally, attach the back of the drawer by
lining up the yellow (B) and green (A) stickers
with the stickers on the drawer sides, making
sure the groove at the bottom creates a
continual line between the back and sides.
16
Repeat steps 12 through 15 for all
five drawers.

12
17
Pull out the bottom-most drawer tracks from
the dresser as far as they’ll go. Disengage
the orange pin at the front of each track by
18
Lay the drawer onto the tracks. The back
corners of the drawer each have little
holes, and the tracks have corresponding
hooks. The hook should slip into the holes
to lock the back of the drawer in place.
pulling the trigger inward. The pins should
be flush with the inside of the track before
placing the drawer.

13
19
Once that’s in place, lower the front of the
drawer onto the track. Here, there are two
pins: one gray and one orange. The gray pin
will fit into the bottom edge of the drawer.
The orange pin fits into the inside edge of
the drawer, horizontally, and is engaged by
switching the orange tabs outward. You
should feel a satisfying click once they’re in
place.
20
Repeat steps 17 through 19 for all five
drawers, working from bottom to top. If
the drawer isn’t shutting fully, or seems
misaligned, make sure all connection pins/
inserts between the drawer and the tracks are
complete. Then, you’re all set! Time to Marie
Kondo your closet and start using your new
Prospect Dresser. Be sure to tag @burrow on
Instagram and use the hashtag #myburrow to
share your setup with us.
Tip: If the drawers seem uneven, rotate the
circle-shaped tab at the end of the drawer
sliders to raise or lower the height of each
side. Push the tab in to lower, pull it toward
the front to raise.

14
1
The holes along the top edge of the back
wall panel allow the anti-tip hardware to
connect from the inside of the dresser to
your wall. Lean the back wall panel against
2
Without moving the back wall, repeat the
process on the other side, using the
printed ruler.
your wall, and using the printed ruler to the
right, mark two spots on your wall for each
bracket, as indicated. This is where the
anchors and wall claw screws will go.
Anti-tip hardware template

15
3
You can set the back wall panel aside
after that, and return to step 3 to continue
assembling your dresser.
Mark a spot on the wall here, for the
top screw
Mark a spot on the wall here, for the
bottom screw
Align center of hole here
Measurement tool

Need a hand?
Send an email to [e-mail]
or text us at [phone] and our
world-class support team will help you
sort things out.