Cineo Maverick User manual

User Guide
Revision 1.2 — May, 2016
Information and specifications in this document are
subject to change without notice.
www.cineolighting.com

2
Cineo Maverick is a versatile Remote
Phosphor light source developed by Cineo
Lighting.
Rather than use traditional diffusion to soften
the light source, the light from a Cineo
Maverick is actually emitted from the Remote
Phosphor panels on the front of the fixture,
providing a true 160° lambertian emitter. This
allows Maverick to wrap your subject in soft
light with edgeless shadows. The phosphor
panels are excited by blue LEDs, which are
automatically turned off when the top lid is
lifted. Like all Cineo Remote Phosphor soft
lights, Maverick allows the user to change
the color temperature panels, supporting
CCT of 2700K, 3200K, 4300K, 5600K, 6500K,
Chroma Blue and Green.
The CineoColor Remote Phosphor panels
used in Maverick perfectly match all other
Cineo soft lights, with Extended CRI ratings
of 94-98, depending on color temperature.
Cineo Color also utilizes deeper red values
optimized for camera capture to ensure
the most natural light on skin tones. The
color temperature of Maverick is extremely
consistent fixture to fixture, and will
not change over time like other lighting
technologies.
Maverick operates from many power options,
including AC, DC and battery power. The on
board power connection uses an industry
standard XLR4 connector with an input
voltage range of 10.8 to 28 VDC. Dimming
options include both local rotary dial and built-
in DMX control.
Maverick fixtures feature a versatile
mounting system that supports a variety
of industry-standard hardware for virtually
limitless mounting options. Cineo Maverick
fixtures are extremely durable, built to last
with anodized alloy construction, flexible
polycarbonate panels, and field-serviceable
components.
Cineo Maverick is perfect for any film or
television project, in the studio or on location,
or anywhere flicker-free, color-accurate soft
light is required.
Welcome to Cineo Maverick

3
General Notes
1. Please read through this manual carefully before operating Cineo Maverick, and keep this
manual for future reference.
2. There are numerous safety instructions and warnings that must be adhered to for your own
safety.
3. Maverick is not intended for residential use. It is intended for professional use only.
4. Maverick service must be performed by a qualified technician.
5. Although Maverick is weather-resistant, the fixture is intended primarily for indoor use.
6. Cineo products are not certified for use in hazardous locations.
7. Maverick has a typical operating temperature of 120º F (50° C).
Fixture Set Up
1. Read these safety instructions carefully to ensure fixture and accessories are used safely.
2. It is suggested that the fixture is correctly mounted onto the supporting surface before use.
3. Ensure the Maverick and power sources are operated within an ambient temperature range
of -4 to 122°F (20 to +50°C)

4
System Components, Connections and Controls
Maverick Lamphead
Maverick3 is the next generation of Remote Phosphor professional lighting, incorporating
simple operation, advanced passive cooling and versatile configuration options. Local 0-100%
dimming is facilitated with a simple rotary control. Depending on Maverick model, DMX may
be added or included to provide remote control of the fixture. Maverick can be configured to
run on battery, DC or AC power sources. Maverick typically includes a mounting yoke that can
be easily adjusted along and removed from the industry standard 80/20 profile mounting slot.
The 80/20s also accommodate a variety of other mounting options from 3rd party sources.
The lamphead can be operated in inclement weather conditions, and although not completely
waterproof it can withstand moderately wet conditions. Depending on input power and CCT,
Maverick can output up to 8,000 lumens.

5
Maverick Power Sources
The Maverick fixture features SmartPower™ power control, allowing operation with any 12-
24VDC power source capable of delivering 75 -150 watts. This provides compatibility with a
wide range of battery and AC options. Configuration of SmartPower is covered in detail in the
Advanced Power Setting section of this guide.
Cineo offers a variety of power accessories that can be mounted directly to the fixture, on the
Maverick yoke, or to the BackPak™ accessory bracket. Maverick can be used with virtually
any nominal 12-24VDC power source, including camera batteries, car lighter sockets, etc.
Adapters and accessory cables are sold for connection to various power sources, including the
following:
900.0095 120w Portable AC Adapter
900.0195 150w studio power supply
900.0086 V-Lock battery plate
900.0094 Gold-Mount plate
Input power from other sources is also possible, using an XLR4 connector with the following
pin configuration:
• Pin1 – GND
• Pin2 – NC
• Pin3 – NC
• Pin4 - +VDC
900.0086 V-Lock battery plate
900.0094 Gold-Mount plate

6
Cineo SmartPower™
Intelligent management of output performance
Cineo Maverick advances portable lighting power by bundling several features that optimize
the Cineo Maverick for various powering conditions. This protects your battery investment and
provides flexibility for studio and portable AC operation.
By default, the Maverick operates at 120 watts on AC power with a lightweight, removable AC
adapter. For studio operation, the Maverick can be can run at 135 watts on a more permanent,
heavy-duty AC adapter. Under battery power, the Maverick is capable of operating with a
standard-capacity, 6.5 amp battery with either V-Lock or Gold Mount options. If you plan to
operate with high-capacity 10 amp batteries, the fixture can be switched to provide maximum
output with larger batteries.
The light output of most portable fixtures diminishes with the decrease in battery voltage,
which can result in unstable light output and potentially damaged batteries. Cineo SmartPower
is designed to give constant light output as the battery voltage decreases, shutting off before
the current draw on the battery becomes excessive.
100%
90%
80%
70%
60%
50%
O 0 5 10 15 20 25 30 35 40 45 50 55 60
SmartPower Controlled Output
(Maverick)
Fixture Output Over Time
(Typical)
Runtime in Minutes
Light Output (percent)
Typical Light Output Over Time

7
Determining Maverick Model
Maverick1
Instructions in nthroughout user guide.
Purchase date: pre-2016
Maverick2
Instructions in nthroughout user guide.
Purchase date: January 2016-June 2016
Maverick3
Instructions in nthroughout user guide.
Purchase date: June 2016-onward
Purchase date: pre-2016
Purchase date: January 2016-June 2016

8
Advanced Power Settings
Maverick 1&2
SmartPower™ settings are configured on a set of DIP switches located inside the lamphead.
By placing these switches inside the fixture, misuse of various power configurations is
minimized, as the fixture should be set up with the power sources intended for use in mind.
The simplest way to think about the SmartPower settings is to consider the maximum power
capability of your DC source below 18 VDC (low voltage setting) and the option of limiting
power draw at a nominal 24 VDC (high voltage setting).
Accessing the DIP switches
1. Remove the bottom panel from the lamphead by removing the two large plus two smaller
screws, as shown.
2. The two DIP switches are located at the bottom of the fixture, slightly left of center, as
shown.
Batteries – Low Voltage (LV) Setting
A standard capacity V-Lock or Gold Mount battery will draw 70-95 watts with an output
ranging from 10.5 to 16 VDC. A high-capacity battery will typically draw 120-150 watts with a
similar output voltage range.
If the Maverick is being used with standard capacity batteries, the LV setting should be set to
75 watts; if the fixture will only be used with high-capacity batteries, the LV setting can be set
to 120 watts.
The LV setting is indicated by the status of the RED LED on the back of the fixture. If the Red
LED is ON, the LV setting is 75W. If the red LED is OFF, the LV setting is 120 watts.
To set the LV mode:
1. Note the location of the DIP switch labeled “Option A.” This switch controls the LV setting.
2. To set the LV mode to 75W, depress the “Option A” switch with a small pin. The red LED
on the back of the fixture will be ON when power is applied.
3. To set the LV mode to 120W, lift the “Option A” switch to the up position. The red LED on
the back of the fixture will be OFF when power is applied. The 120W LV setting should
only be used with batteries whose output equals or exceeds 120 watts. Using this LV
setting with a standard capacity battery may damage the battery.
shown.
Batteries – Low Voltage (LV) Setting
n n

9
NOTE: if the LV setting is 75 watts, virtually any capacity camera battery will work well with
Maverick, without damage to the battery. Therefore, this is the default setting when the
fixture is shipped from the factory.
AC Operation – High Voltage setting (HV)
The Maverick fixture is designed for use with a 24VDC AC adapter when used on house
power. The HV switch allows the fixture to be configured for use at 120 watts or up to 135
watts, depending on the application.
If Maverick is being used with a 120w power supply, the HV setting should be set to 120w
mode; if the fixture will be used with a 150w power supply, the HV setting should be set to
135w mode.
To set the HV mode:
1. Note the location of the DIP switch labeled “Option B.” This switch controls the HV setting.
2. To set the HV mode to 120w, depress the “Option B” switch with a small pin. The yellow
LED on the back of the fixture will be ON when power is applied.
3. To set the HV mode to 135w, lift the “Option B” switch
to the up position. The yellow LED on the back of the
fixture will be OFF when power is applied. The 135w HV
setting MUST be powered with a 150 watt or greater
power source or damage to the power source may
occur.
NOTE: The default factory setting for HV mode is 120w.
Maverick 3
Power Settings
1. Push and hold local knob for approx. 15 seconds, Display shows bfor battery.
2. Rotate knob to L(Low capacity 75W battery mode) or H(High capacity 120W battery
mode). The 120W High Power setting should only be used with batteries whose output
equals or exceeds 120 watts. Using this battery High Power setting with a standard
capacity battery may damage the battery. Push knob to select.
3. Display shows AC. Rotate knob to L(Low power 120w
mode) or H(High power 135w mode). The 135w high
power setting MUST be powered with a 150 watt or
greater power source or damage to the power source
may occur. Push knob to select and return to normal
operation.
n

10
Local and Remote Dimming
Maverick 1 & 2:
When correct DC power is applied to the unit, the green
LED illuminates on the back, between the cooling fins. The
output of the Maverick is controlled with the local control
knob on the back of the fixture. The fixture does not employ
an on/off switch; when the knob position is at 0 the fixture is
virtually off, as it draws only 10 ma of power. The dimming
curve is logarithmic in nature, providing a very “analog”
characteristic to its control.
Remote Dimming via DMX
Cineo offers a DMX interface module for control of the
fixture via standard DMX lighting protocol. The interface
module (900.0087) attaches to either the yoke or the
BackPak accessory and connects to the Maverick fixture’s
AUX port via an included RJ45 cable. The module includes
both DMX IN and DMX THRU via standard 5-pin XLR connections. The DMX pin-out wiring is
as follows:
• Pin 1: Signal Common
• Pin 2: Data –
• Pin 3: Data +
• Pin 4: Spare
• Pin 5: Spare
The DMX control line is automatically self-terminating and does not require external DMX
termination when no cable is inserted into the DMX THRU connector.
Note that when the DMX control is in use and DMX signal is lost, the fixture will hold its last
level. When the Maverick loses power, it retains all of its DMX settings when the power is
resumed.
DMX Module Operation
When the DMX module is connected to the Maverick fixture, control of the fixture is
automatically switched to the module. The DMX module has a multi-line display screen that
indicates the firmware level, control mode (local/remote) and DMX address. The module is
programmed by the use of four capacitive-touch buttons below the screen (-, +, Mode, Save).
There are two control modes: one for determining local or DMX control, and one for setting
the DMX address (0-255). Touching the Mode button toggles the arrow on the right of the
screen between these modes.
When the arrow is pointing to the “Control” setting, the “-“ and “+” buttons will switch
between local and DMX control. When the desired control method is displayed, touch the
“Save” button to lock the setting. If the setting is not saved, it will revert to its previous
setting in a few seconds.
n n

11
When the arrow is pointing to the “Address” mode, the “-“ and “+” buttons will increase
or decrease the DMX address setting to the desired address. When the desired address is
displayed, touch the “Save” button to lock the setting. If the setting is not saved, it will revert
to its previous setting in a few seconds.
Disconnecting the DMX module from the Maverick fixture will place the fixture back into local
control.
Maverick 3:
Local Mode:
1. Push local control knob for 5 seconds. The digital display shows current mode.
2. Rotate knob to scroll between the two modes: Loc or Add. Push the knob to select Loc.
3. Display shows dim level. Rotate knob to adjust.
Note: Double pushing the local control knob turns the fixture off. Pushing the button again
turns the fixture on to its previous light level setting.
DMX Mode:
DMX control is built into the Maverick3 and no external DMX module is necessary.
To set DMX address:
1. Push local control knob for 5 seconds. The digital display shows current mode.
2. Rotate knob to scroll between the two modes: Loc or Add. Push knob to select. DMX
address flashes.
3. Turn knob to select DMX address. Push knob to select. Display shows DMX address
selected.
Maintenance Mode (Maverick 3 Only):
The Maverick 3 includes a maintenance mode that displays the firmware version running on
the fixture, as well as performing a system calibration cycle. To enter the maintenance mode,
perform the following steps:
1. Disconnect power from the fixture for at least 30 seconds.
2. Depress and hold the knob while re-powering the fixture.
3. The display will show the current firmware version, then perform a self-calibration.
4. When complete, the fixture will return to its previous operating mode.
n

12
Remote Phosphor Panels
Color temperature (CCT) for the Maverick is changed by replacing the Remote Phosphor panel
on the front of the fixture. The CCT is clearly labeled on each panel.
902.1227 Maverick Phosphor Panel - 2700k
902.1232 Maverick Phosphor Panel - 3200K
902.1243 Maverick Phosphor Panel - 4300K
902.1256 Maverick Phosphor Panel - 5600K
902.1265 Maverick Phosphor Panel - 6500K
902.1240 Maverick Phosphor Panel - Chroma Blue
902.1250 Maverick Phosphor Panel - Chroma Green
To change RP panels:
1. Loosen the two thumbscrews at the top of the fixture, and
remove the top plate.
Maverick 1: The top plate is tethered to the body of the fixture to
avoid loss or damage.
Maverick 2&3: The top plate is hinged.
2. Remove the RP panel by sliding it up and out of the fixture. If the
lamp is on, the output will be cut.
3. Insert a new panel into the slots and firmly seat it into the bottom
of the slot.
4. Close the top door, tightening the two thumbscrews finger tight.
Mounting and Accessory Attachment
Maverick has an integrated slot in front of the RP panel for attachment of light control
accessories, including the following:
900.0088 90º louver
900.0089 4-leaf Barndoor set
902.0100 Snapbag™ softbox
902.0101 Chimera™ softbox
To remove/install the yoke:
1. Position the yoke 90º to the body of the fixture.
2. With a #2 Phillips screwdriver, loosen the (4) mounting screws approximately one
revolution.
3. Slide the yoke out of the 80/20 slot.
4. Installation is in reverse order.
n
n n
n n n

13
Maverick 1:
To install / remove the Accessory Backpak::
1. Align the attached oval-shaped nuts at the top of the
BackPak to the top of the 80/20 slot.
2. Slide the top of the BackPak down so the oval nuts on the
bottom can be inserted into the bottom of the 80/20 slot.
3. Position the BackPak in the desired location.
4. Tighten the #2 Phillips screws to secure the BackPak bracket
Maverick 2&3:
Accessories may be attached directly to 80/20 slots on the back of the fixture. To attach
accessories:
1. Slide the accessory plate into the 80/20 slot on the back of the fixture.
2. Tighten the screws with a #2 Phillips screwdriver to secure the accessory plate.
n n
n

14
Specifications
Lamphead
Input voltage: 10.5-28 VDC
Power consumption: 75 watts / 120 watts / 135 watts (user configurable)
4-pin XLR power input
Maverick 1&2: EtherCon DMX port, connecting to external DMX module
Maverick 3: DMX in/thru on-board
Completely silent, flicker-free operation
Fixture dimensions: 9.4” x 7.3” x 3” (240mm x 186mm x 78mm)
Weight: 2.2 kg (4.9 lbs)
Maximum output: 8,000 lumens
Beam Angle: >160º
Max. temperature rise: +45° C above ambient
Environmental temperature range: 20° - 50° C
35,000 hr. L70 rated
2-year parts and labor warranty
ETL and cETL certified, CE Compliant
Zero UV light emitted
Made in USA
Maverick Power Sources
120w AC Adapter
Part # 900.0095
Input Voltage: 100-240VAC
Output Voltage: 24VDC
Max. output current: 5A
Output connector: XLR4
Dimensions: 6.61” x 2.8” x 1.48” (168mm x 71mm x 37.2mm)
Weight: 1.5 lb. (680.3g)
2-year parts and labor warranty
UL, cULus and CE listed

15
150w AC Adapter
Part # 900.0195
Input Voltage: 100-240VAC
Output Voltage: 24VDC
Max. output current: 6.25A
Output connector: XLR4
Dimensions: 6.5” x 3.25” x 1.58 (165.1mm x 82.8mm x 40.1mm)
Weight: 2.25 lb. (1.0 kg)
2-year parts and labor warranty
UL, cULus and CE listed
900.0086 V-Lock Battery Plate
Max output current: 10A
Output connector: XLR4
Dimensions: 5.6” x 3.2” x 1” (142.1mm x 82.3mm x 26.3mm)
Weight: 13 oz. (368.5 g)
900.0094 Gold-Mount Plate
Max output current: 10A
Output connector: XLR4
Dimensions: 4.7” x 3.9” x 1.7” (119.6mm x 76.5mm x 17.8mm)
Weight: 9.2 oz. (260.8 g)
DMX Interface Module
Interface connector: Ethercon F
DMX connectors: XLR5 IN / THRU, self-terminating
Dimensions: 3.0” x 3.9” x 1.7” (77.2mm x 99mm x 43.7mm)
Weight: 7.3 oz. (207 g)

16
Warnings, Disclaimers and Warranty
Burning Injuries
Be aware of high temperatures in excess of 50ºC inside the lamphead during and after fixture
use. To avoid burning injuries, do not touch the LEDs.
Flammable Materials
Keep flammable materials away from the installation. Ensure that the amount of air flow
required for safe operation of the equipment is not compromised. Proper ventilation must be
provided.
ESD and LED’s
LED components used in Maverick are ESD (Electro-Static Discharge) sensitive. To prevent
the possibility of destroying LED components do not touch either while the fixture is in
operation or while it is switched off.
Blue Light Output
Do not bypass the lamphead safety switches that turn off the blue LEDs when phosphor
panels are removed. The light-output intensity may be harmful to human eyes. No UV or IR is
emitted at any time from this fixture.
AC Power Supplies and DC Cables
Use only a rated AC power supply. The user is responsible for ensuring DC power cables are
of adequate condition for each application. If the cables are damaged, replace them with new
ones.
Environmental: Disposal of Old Electrical & Electronic Equipment
This product shall not be treated as household waste.

17
CINEO LIGHTING LIMITED WARRANTY
Products from Cineo Lighting are warranted against defects in materials and workmanship
for two years from the date the Product is shipped to Customer. Products are guaranteed
to perform substantially in accordance with the accompanying written materials within the
warranty period under normal use.
If the Product fails to work as warranted, Cineo Lighting will, in its sole discretion, repair or
replace the Product with a new or remanufactured Product that is at least equivalent to the
original Product. Customer must obtain a Return Material Authorization number from Cineo
Lighting before returning any Products under warranty to Cineo Lighting.
Customer shall pay expenses for shipment of repaired or replacement Products to Cineo
Lighting’s repair facility. Any repaired or replaced Products will be warranted for the remainder
of the original warranty period or thirty (30) days, whichever is longer. Cineo Lighting will
pay shipping of repaired goods back to the customer. After examining and testing a returned
product, if Cineo Lighting concludes that a returned product is not defective, Customer will be
notified, the product returned at Customer’s expense.
This Limited Warranty is void if failure of the Products has resulted from accident, abuse,
misapplication, or use outside of normal operating conditions. Warranty is void if serial number
has been defaced or removed.
NO OTHER WARRANTIES. EXCEPT AS EXPRESSLY SET FORTH ABOVE, THE
PRODUCTS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, AND NO
OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED ARE MADE WITH RESPECT
TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE OR NON-
INFRINGEMENT OR ANY OTHER WARRANTIES THAT MAY ARISE FROM USAGE OF
TRADE OR COURSE OF DEALING. ELEMENT DOES NOT WARRANT, GUARANTEE, OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OF OR THE RESULTS OF THE
USE OF THE PRODUCTS IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY, OR
OTHERWISE AND DOES NOT WARRANT THAT THE OPERATION OF THE PRODUCTS WILL
BE UNINTERRUPTED OR ERROR FREE. CINEO LIGHTING EXPRESSLY DISCLAIMS ANY
WARRANTIES NOT STATED HEREIN. NO LIABILITY FOR CONSEQUENTIAL DAMAGES.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL
ELEMENT AND ITS LICENSORS, DISTRIBUTORS, AND SUPPLIERS (INCLUDING ITS
AND THEIR DIRECTORS, OFFICERS, EMPLOYEES, AND AGENTS) BE LIABLE FOR ANY
DAMAGES, INCLUDING, BUT NOT LIMITED TO, ANY SPECIAL, DIRECT, INDIRECT,
INCIDENTAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS,
INSTALLATION COSTS, LOST SAVINGS, BUSINESS INTERRUPTION, LOST BUSINESS
INFORMATION, OR ANY OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PRODUCTS, EVEN IF ELEMENT OR ITS LICENSORS, DISTRIBUTORS, AND
SUPPLIERS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CINEO
LIGHTING’S TOTAL LIABILITY ON ALL CLAIMS, WHETHER IN CONTRACT, WARRANTY,
TORT (INCLUDING NEGLIGENCE OR BREACH OF STATUTORY DUTY), STRICT LIABILITY
OR OTHERWISE, SHALL NOT EXCEED THE AMOUNTS PAID BY CUSTOMER FOR THE
PRODUCTS.
Customer acknowledges that the applicable purchase price or license fee for the Products
reflects this allocation of risk. Because some states/jurisdictions do not allow the exclusion
or limitation of liability for consequential or incidental damages, the above limitation may not
apply. The above limitations shall apply notwithstanding the failure of any limited remedy to
fulfill its essential purpose.

www.cineolighting.com
Specifications are subject to change
without notice. Cineo Lighting, Cineo
Maverick and Maverick are registered
trademarks of Cineo Lighting, Inc.
©2016 Cineo Lighting, Inc. v05.25.16
Cineo Lighting
P.O. Box 808
El Granada, CA 94018
Silicon Valley | Los Angeles | London
[email protected]
+1 310.425.3425