Cisco WAE-674-K9 - Wide Area Application Engine... User manual

Americas Headquarters:
© 2007–2008 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Installing the Cisco WAE Inline Network Adapter
Product Number: WAE-INLN-4CG=
Models: FE-511-K9, WAE-511-K9, WAE-611-K9, WAE-512-K9, WAE-612-K9, WAE-7326-K9, WAE-7341-K9,
WAE-7371-K9, WAE-674-K9
This document describes how to install the Cisco WAE inline network adapter in your edge or core WAE
appliance. These instructions are intended for experienced technicians.
Note The Cisco WAE inline network adapter is not supported in a Central Manager appliance. (For more
information, see the “Important Operational Notes” section on page 7.)
Contents
This document contains the following sections:
•Product Overview
•Safety Guidelines
•Important Operational Notes
•Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
•Installing Adapters in the WAE-512 and WAE-612 Appliances
•Installing Adapters in the WAE-7326 Appliance
•Installing Adapters in the WAE-7371, WAE-7341, and WAE-674 Appliances
•Cabling
•Related Documentation
•Obtaining Documentation, Obtaining Support, and Security Guidelines

2
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Product Overview
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Product Overview
This section contains the following topics:
•Inline Network Adapter Description
•Ports and LED Indicators
•Adapter Specifications
Note The minimum software release required for the inline network adapter is WAAS 4.0.7.
Inline Network Adapter Description
WAAS software versions prior to 4.2.1 support one optional 4-port Ethernet inline network adapter on
WAE-7341/WAE-7371/WAE-674 appliances. Up to two inline network adapters are supported using
WAAS software version 4.2.1 or later.
The inline network adapter is a full-height, three-quarter-length PCI-X network interface card that
contains four independent Gigabit Ethernet ports. (See Figure 1.)
Figure 1 Inline Network Adapter
159701

3
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Product Overview
The Cisco WAE inline network adapter provides an inline traffic interception capability for your
appliance. When you configure the WAE appliance for inline interception mode, you can set attributes
to control which interfaces are to be used over which VLANs. By default, the adapter operates on all
inline-capable interfaces and VLANs. You can configure the inline redirection feature using the WAAS
4.0.7 CLI or the WAAS 4.0.7 Central Manager GUI.
The WAAS software defines two new interface types: A group interface that represents an inline pair
grouping and a port interface that represents the individual port. These interfaces are referred to as
inlineGroup and inlinePort.
InlineGroup interfaces are numbered using the format slot/group. The slot number is the slot in which
the adapter is inserted. (In the WAE 500 series and 600 series appliances, you must install the adapter in
slot 1 only.) The group number is either 0 or 1 (each adapter has 2 group pairs). The group number is
displayed on the adapter label.
InlinePort interfaces are numbered slot/group/lan or slot/group/wan. The last attribute is the LAN or
WAN designator.
The inline network adapter also includes an onboard programmable watch dog timer (WDT) controller
that allows you to set the time to wait after a failure event, such as a power outage or a kernel crash,
before the unit begins to operate in mechanical bypass mode. In mechanical bypass mode, traffic is
bridged between the LAN and WAN ports of each group. Mechanical bypass mode prevents the WAE
from becoming a single point of failure and allows traffic to continue to flow between the router and the
client while it passes through an unresponsive WAE without being processed.
For more information about configuring the inline network adapter, see the Cisco Wide Area Application
Services Configuration Guide.
Ports and LED Indicators
Figure 2 shows the inline network adapter port numbers, interface designations, and LEDs.
Figure 2 Inline Network Adapter Port Numbering and LEDs
The inline network adapter has three LEDs that correspond to each port (the W1 LEDs correspond to
Port W1, and so forth). Table 1 describes the LEDs.
W1 Port WAN1; Group 1 WAN interface L1 Port LAN1; Group 1 LAN interface
W0 Port WAN0; Group 0 WAN interface L0 Port LAN0: Group 0 LAN interface
W1 L1 W0 L0
LINK/ACT
100
1000 BYPASS
W1 L1 W0 L0
272072

4
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Product Overview
Note On older inline network adapters, the LEDs are labelled 0, 1, 2, and 3. These correspond to W1, L1, W0,
and L0 respectively.
Adapter Specifications
Table 2 describes the inline network adapter technical and general specifications.
Table 1 Inline Network Adapter LEDs
LEDs State Description
Link / Activity On The 10/100/1000BASE-T interface is receiving power.
Blinking The Ethernet link is transmitting data.
100 On The speed of the Ethernet connection is 100BASE-TX.
1000 On The speed of the Ethernet connection is 1000BASE-TX.
Bypass Both the 100 and
1000 LEDs are on
The corresponding ports are in mechanical bypass mode.
Table 2 Inline Network Adapter Specifications
Specification Description
Copper Gigabit Ethernet Specifications
IEEE standard Gigabit Ethernet, 1000BASE-T
Fast Ethernet, 100BASE-T
Ethernet, 10BASE-T
Full duplex and half duplex Supports both half-duplex and full-duplex operation in all
operating speeds
Autonegotiation Autonegotiates between full-duplex and half-duplex operations
and between 1000-Mbps, 100-Mbps, and 10-Mbps speeds
Data transfer rate 1000-Mbps, 100-Mbps, and 10-Mbps speeds per port in
half-duplex mode
2000-Mbps, 200-Mbps, and 20-Mbps speeds per port in
full-duplex mode
General Technical Specifications
Interface standard PCI v2.2 32/64 bit, 33/66 MHz
PCI-X v1.0 32/64 bit, 66/100/133 MHz
Size 6.6 x 4.2 in. (167.64 x 106.68 mm)
PCI connector Universal 64-bit connector
PCI voltage +12 V (minimum 11.4 V, maximum 12.6 V)
+3.3 V (minimum 3.0 V, maximum 3.6 V)
Weight 6.18 oz (175 grams)

5
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Safety Guidelines
Safety Guidelines
To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the
following precautions:
•Warnings
•General Precautions
•Protecting Against Electrostatic Discharge
Warnings
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover
installed. Operating the unit without the cover in place will invalidate the safety approvals and pose
a risk of fire and electrical hazards. Statement 117
Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous
voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might
disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate
the system unless all cards and faceplates are in place. Statement 156
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Operating humidity 0 to 90%, noncondensing
Operating temperature 32 to –122oF (0 to 50oC)
Storage temperature –4 to –149oF (–20 to –65oC)
Table 2 Inline Network Adapter Specifications
Specification Description

6
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Safety Guidelines
General Precautions
Observe the following general precautions for using and working with your system:
•Observe and follow service markings. Do not service any Cisco product except as explained in your
system documentation. Opening or removing covers that are marked with the triangular symbol with
a lightning bolt may expose you to electrical shock. Components inside these compartments should
be serviced only by an authorized service technician.
•If any of the following conditions occur, unplug the product from the electrical outlet and replace
the part or contact your authorized service provider:
– The power cable or plug is damaged.
– An object has fallen into the product.
– The product has been exposed to water.
– The product has been dropped or damaged.
– The product does not operate correctly when you follow the operating instructions.
•Keep your system components away from radiators and heat sources. Also, do not block cooling
vents.
•Do not spill food or liquids on your system components, and never operate the product in a wet
environment.
•Do not push any objects into the openings of your system components. Doing so can cause fire or
electric shock by shorting out interior components.
•Use the product only with other Cisco-approved equipment.
•Allow the product to cool before removing covers or touching internal components.
•Use the correct external power source. Operate the product only from the type of power source
indicated on the electrical ratings label. If you are not sure of the type of power source required,
consult your service representative or local power company.
•Use only approved power cables. If you have not been provided with a power cable for your
Content Engine or for any AC-powered option intended for your system, purchase a power cable that
is approved for use in your country. The power cable must be rated for the product and for the
voltage and current marked on the product’s electrical ratings label. The voltage and current rating
of the cable should be greater than the ratings marked on the product.
•To help prevent electric shock, plug the system components and peripheral power cables into
properly grounded electrical outlets. These cables are equipped with three-prong plugs to help
ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable.
•Do not use appliance or voltage converters or kits sold for appliances with your product.
•To help protect your system components from sudden, transient increases and decreases in electrical
power, use a surge suppressor or line conditioner.
•Position cables and power cords carefully; route cables and the power cord and plug so that they
cannot be stepped on or tripped over. Be sure that nothing rests on your system components’ cables
or power cord.
•Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local or national wiring rules.

7
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Important Operational Notes
Protecting Against Electrostatic Discharge
Static electricity can harm delicate components inside your system. To prevent static damage, discharge
static electricity from your body before you touch any of your system’s electronic components. You can
do so by touching an unpainted metal surface on the chassis.
You can also take the following steps to prevent damage from electrostatic discharge (ESD):
•Limit your movement. Movement can cause static electricity to build up around you.
•When transporting a sensitive component, first place it in an antistatic container or packaging.
•Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your
body by touching it to an unpainted metal part of the system unit for at least 2 seconds.
•Remove the adapter from its packaging and install it directly into your system unit without setting
it down. If it is necessary to set the adapter down, place it in its static-protective package. Do not
place the adapter on your system unit cover or on a metal table.
•Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and
workbench pads.
•Handle the adapter carefully, holding it by its edges or its frame.
•Do not touch solder joints, pins, or exposed printed circuitry.
•Do not leave the adapter where others can handle and possibly damage the adapter.
•Take additional care when handling adapters during cold weather because heating reduces indoor
humidity and increases static electricity.
Important Operational Notes
If you intend to reconfigure an edge or core WAE with a Cisco WAE inline network adapter installed in
it as a Central Manager device, first remove the inline network adapter. The inline network adapter is not
supported in a Central Manager appliance.
Installing Adapters in the FE-511, WAE-511, and WAE-611
Appliances
This section describes how to install the inline network adapter in the FE-511, WAE-511, and the
WAE-611 appliances. This section includes the following procedures:
•Removing the Cover
•Installing an Inline Network Adapter
•Completing the Installation

8
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
Removing the Cover
Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Statement 1
To remove the cover, follow these steps:
Step 1 Review the information in the “Safety Guidelines” section on page 5.
Step 2 Power down the appliance and all attached devices. Disconnect the power cord and all external cables.
Step 3 Loosen the two captive screws (labeled 1 in Figure 3) on the rear of the cover.
Figure 3 Removing the Cover
Step 4 Slide the cover back, and then lift it up and off the appliance.
Caution For proper cooling and airflow, replace the cover before turning on the appliance. Operating the
appliance for extended periods (over 30 minutes) with the cover removed might damage appliance
components.
115802
1

9
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
Installing an Inline Network Adapter
Before you install an adapter, review the following information:
•The adapter slots are on the riser card assembly. You must first remove the riser card assembly to
access the adapter slots. (See Figure 4.)
•The appliance has two Peripheral Component Interconnect-Extended (PCI-X) adapter slots:
– PCI-X slot 1 is for one full-height three-quarter-length adapter.
– PCI-X slot 2 is for one low-profile half-length adapter; however, it is not used in this appliance.
•You must install the inline network adapter in PCI-X slot 1. (This slot is labeled “PCI 1” on the back
of the appliance.)
Caution When you handle static-sensitive adapters and appliances, take precautions to avoid damage from static
electricity. For details on handling these devices, see the “Protecting Against Electrostatic Discharge”
section on page 7.
Note The illustrations in this document might differ slightly from your hardware.
To install an inline network adapter, follow these steps:
Step 1 Review the safety information in the “Safety Guidelines” section on page 5.
Step 2 Power down the appliance and peripheral devices.
Step 3 Disconnect the power cord and then all external cables from the appliance.
Step 4 Remove the appliance cover.
Note You may find it easier to route the cables before you install the adapter.
Step 5 Loosen the captive screw (labeled 3 in Figure 4) located on the rear of the appliance adjacent to PCI-X
slot 1 and remove the expansion slot cover.
Note You must install PCI expansion slot covers on all vacant slots so that you can maintain the
electronic emissions characteristics of the appliance and ensure proper cooling of internal
components.

10
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
Figure 4 Removing the Expansion Slot Cover
Step 6 Remove the riser card (labeled 1 in Figure 5) from the system board to access the expansion slot.
1Expansion slot cover (slot 2) 2Expansion slot cover (slot 1)
3Captive screw 4Riser card assembly
1
2 4
3
124478

11
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
Figure 5 Installing an Adapter in the Riser Card Assembly
Step 7 Touch the static-protective package that contains the adapter to any unpainted metal surface on the
appliance, and then remove the adapter from the static-protective package. Avoid touching the
components and gold-plated edge connectors on the adapter.
Step 8 Place the adapter, component-side up, on a flat, static-protective surface and set any jumpers or switches
as described by the adapter manufacturer, if necessary.
Caution When you install an adapter in the appliance, be sure that it is completely and correctly seated in the PCI
expansion slot before you power up the appliance. Incomplete insertion might cause damage to the
system board or the adapter.
Step 9 To install the adapter, carefully grasp the adapter by its top edge or upper corners, align it with the PCI-X
slot 1 connector (labeled 3 in Figure 5), and then press the adapter firmly into the expansion slot.
1Riser card 2PCI-X slot 2 connector
3PCI-X slot 1 connector 4Adapter support bracket
5Adapter 6PCI-X riser card connector
4
5
321
6
124479

12
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
Step 10 Reinstall the riser card. Make sure that the riser card is fully seated in the riser card connector (labeled
6 in Figure 5) on the system board.
Step 11 Tighten the captive screw for expansion slot 1.
Step 12 Connect the required cables to the adapter.
Completing the Installation
To complete your installation, reinstall the cover and reconnect all cables that you disconnected earlier.
Caution To maintain proper cooling and airflow, install the cover before turning on the appliance. Operating the
appliance for extended periods (over 30 minutes) with the cover removed might damage internal
components.
To install the cover, follow these steps:
Step 1 Install the cover by placing it into position and sliding it forward, and then tighten the captive screws
(labeled 1 in Figure 6).
Caution Before sliding the cover forward, make sure that the cover will properly engage the ledge at the front of
the appliance.
Figure 6 Installing the Cover
Step 2 Install the appliance in the rack.
115802
1

13
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-512 and WAE-612 Appliances
Step 3 Connect all external cables and the power cord to the appliance, and then plug the power cord into a
properly grounded electrical outlet.
Installing Adapters in the WAE-512 and WAE-612 Appliances
This section describes how to install the inline network adapter in the WAE-512 and the WAE-612
appliances. This section includes the following procedures:
•Removing the Cover
•Installing an Inline Network Adapter
•Completing the Installation
Removing the Cover
Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units.
Statement 246
To remove the cover, follow these steps:
Step 1 Review the information in the “Safety Guidelines” section on page 5.
Step 2 Power down the device and all attached devices. Disconnect the power cord and all external cables.
Step 3 Press the cover release button (labeled 1 in Figure 7).
Figure 7 Removing the Cover
Step 4 While holding the cover release button down with your thumb, lift the opposite front corner of chassis
slightly with your other hand, and using your free thumb, slide the cover back approximately 0.5 inches
(1.27 cm); then lift it up and off the device.
151926
CiscoWAE500 Series
1

14
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-512 and WAE-612 Appliances
Caution For proper cooling and airflow, replace the cover before turning on the device. Operating the device for
extended periods (over 30 minutes) with the cover removed might damage device components.
Installing an Inline Network Adapter
Before you install adapters, review the following information:
•The adapter slots are on the riser card assembly. You must first remove the riser card assembly to
access the adapter slots. (See Figure 8.)
•The device has two Peripheral Component Interconnect-Extended (PCI-X) adapter slots:
– PCI-X slot 1 is for one full-height three-quarter-length adapter.
– PCI-X slot 2 is for one low-profile half-length adapter; however, it is not used in this device.
•You must install supported adapters in PCI-X slot 1. (This slot is labeled “Slot 1” on the back of the
device.)
Caution When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For
details on handling these devices, see the “Protecting Against Electrostatic Discharge” section on
page 7.
Note The illustrations in this document might differ slightly from your hardware.
To install an adapter, follow these steps:
Step 1 Review the safety information in the “Safety Guidelines” section on page 5.
Step 2 Power down the device and peripheral devices.
Step 3 Disconnect the power cord and then all external cables from the device.
Step 4 Remove the device cover.
Step 5 Grasp the riser card at the rear edge and lift to remove the riser card assembly. (See Figure 8.)

15
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-512 and WAE-612 Appliances
Figure 8 Removing the Riser Card Assembly
Step 6 Place the riser card assembly on a flat, static-protective surface.
Step 7 Remove the expansion slot cover for Slot 1. (See Figure 9.)
Note You must install PCI expansion slot covers on all vacant slots so that you can maintain the
electronic emissions characteristics of the appliance and ensure proper cooling of internal
components.
1Riser card assembly 2Rear edge of riser card
151927
1
2
Front
Rear

16
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-512 and WAE-612 Appliances
Figure 9 Installing the Adapter in the Riser Card Assembly
Step 8 Touch the static-protective package that contains the adapter to any unpainted metal surface on the
device, and then remove the adapter from the static-protective package. Avoid touching the components
and gold-plated edge connectors on the adapter.
Step 9 Place the adapter, component-side up, on a flat, static-protective surface.
Caution When you install an adapter in the device, be sure that it is completely and correctly seated in the PCI
expansion slot before you power up the device. Incomplete insertion might cause damage to the system
board or the adapter.
Step 10 To install the adapter, carefully grasp the adapter by its top edge or upper corners, align it with the
expansion slot in the riser card assembly, and then press the adapter firmly into the expansion slot.
Step 11 Reinstall the riser card. Make sure that the riser card is fully seated in the riser card connectors on the
system board.
1Expansion slot bracket 2Adapter
3Adapter support bracket 4PCI-X expansion slot 1
5Riser card assembly 6PCI-X expansion slot 2 (not supported)
7Riser card connectors
151928
1
2
3
4
5
6
7

17
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-7326 Appliance
Completing the Installation
To complete your installation, reinstall the cover and reconnect all cables that you disconnected earlier.
Caution To maintain proper cooling and airflow, install the cover before turning on the appliance. Operating the
appliance for extended periods (over 30 minutes) with the cover removed might damage internal
components.
To install the cover, follow these steps:
Step 1 Install the cover by placing it into position and sliding it forward. (See Figure 10.)
Figure 10 Installing the Cover
Caution Before sliding the cover forward, make sure that the cover will properly engage the ledge at the front of
the device.
Step 2 Install the device in the rack.
Step 3 Connect all external cables and the power cord to the device, and then plug the power cord into a properly
grounded electrical outlet.
Installing Adapters in the WAE-7326 Appliance
This section describes how to install the inline network adapter in the WAE-7326 appliance. This section
includes the following procedures:
•Removing the Cover
•Installing an Inline Network Adapter
•Completing the Installation
151932
Cisco WAE500 Series

18
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-7326 Appliance
Removing the Cover
Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Statement 1
To remove the device top cover, follow these steps:
Step 1 Review the information in the “Safety Guidelines” section on page 5.
Step 2 Power off the device and all attached devices and disconnect all external cables and power cords.
Step 3 Press down on the left and right side latches and pull the device out of the rack enclosure until both slide
rails lock.
Note You can reach the cables on the back of the device when the device is in the locked position.
Step 4 Lift the cover-release latch (labeled 1 in Figure 11). Lift the cover off the device and set the cover aside.
Figure 11 Removing the Cover
Caution For proper cooling and airflow, replace the cover before turning on the device. Operating the device for
extended periods (over 30 minutes) with the cover removed might damage device components.
159947
1

19
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-7326 Appliance
Installing an Inline Network Adapter
The WAE-7326 has connectors for up to four PCI adapters on the system board and PCI riser card. You
can install the inline network adapter in slot 3 (labeled 1 in Figure 12) or in slot 4 (labeled 2 Figure 12)
in on the PCI riser card.
Note The PCI riser card is located at J73 on the system board.
Figure 12 PCI-X Riser Card
To install an inline network adapter, follow these steps:
Step 1 Review the information in the “Safety Guidelines” section on page 5.
Step 2 Power down the device and peripheral devices and disconnect all power cords and external cables.
Step 3 Remove the cover. (See the “Removing the Cover” section on page 18.)
Step 4 Remove the PCI riser card assembly.
Step 5 Slide the expansion-slot cover out of the PCI riser card cage.
Step 6 Touch the static-protective package that contains the adapter to any unpainted metal surface on the
device, and then remove the adapter from the static-protective package. Avoid touching the components
and gold-plated edge connectors on the adapter.
Step 7 Place the adapter, component-side up, on a flat, static-protective surface.
Caution When you install an adapter in the device, be sure that it is completely and correctly seated in the PCI
expansion slot before you power up the device. Incomplete insertion might cause damage to the system
board or the adapter.
Step 8 To install the adapter, carefully grasp the adapter by its top edge or upper corners, align it with the
expansion slot in the riser card assembly, and then press the adapter firmly into the expansion slot.
Step 9 Reinstall the riser card. Make sure that the riser card is fully seated in the riser card connectors on the
system board.
Step 10 Connect any needed cables to the adapter.
1PCI-X slot 3, 64 bit 3.3 V 133 MHz (PCI 3) 2PCI-X slot 4, 64 bit 3.3 V 133 MHz (PCI 4)
137707
1
2

20
Installing the Cisco WAE Inline Network Adapter
OL-12480-03
Installing Adapters in the WAE-7326 Appliance
Figure 13 shows the cable routing for an adapter installed in the PCI riser card cage.
Figure 13 Cable Routing for the PCI Riser Card Cage
Caution When you route cables, do not block any connectors or the ventilated space around any of the fans.
Make sure that cables are not routed on top of components under the PCI riser card assembly.
Make sure that cables are not pinched by the server components.
Note Remove the fan guide before you route the cables. Reinstall the fan guide when you complete the cable
routing.
1Riser card cage 2SCSI cable
137691
1
2