Cisco uBR-E-16U User manual

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective
owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (0705R)
© 2009 Cisco Systems, Inc. All rights reserved.
OL-18974-01
QUICK START GUIDE
Installing Cisco uBR-MC16U/X
and uBR-E-16U
Cable Interface Line Cards
1Purpose
2Feature Description
3Prerequisites
4Installing the Card
5Removing the Card
6Troubleshooting
7Technical Specifications
8Related Documentation
Warning Only trained and qualified
personnel should be allowed to
install, replace, or service this
product.
Caution You must be properly grounded
before handling this
ESD-sensitive product.
1 Purpose
This quick start guide shows you how to install a
Cisco uBR-MC16 cable interface line card in the
Cisco uBR7200 series router.
2 Feature Description
The Cisco uBR-MC16 cable interface line card
improves RF performance, supports spectrum
management, increases system performance and
supports online insertion and removal (OIR).
The line card is available in three configurations:
•Cisco uBR-MC16U—With an onboard
upconverter and green end tabs
•Cisco uBR-E-16U—With an onboard
upconverter and slate blue end tabs
•Cisco uBR-MC16X—Without an onboard
upconverter and yellow end tabs
3 Prerequisites
•The Cisco NPE-400 or the Cisco NPE-G1 or
the Cisco NPE-G2 network processing engine
must be used with this card.
•If you are using the Cisco uBR-MC16 line card
to replace a different type of card, you must
reconfigure the MC16U/X/E card.
•We recommend that you reload a Cisco 7200
series router when replacing a cable interface
line card with a card of a different type.
4 Installing the Card
Note The uBR-E-16U line card is an entry-level
version of the uBR-MC16U line card, and
fits only in the uBR7225VXR chassis.
Step 1 Make sure that you are grounded.
Step 2 Use both hands to grasp the line card by its
metal carrier edges and align the line card
with the slot guides, component side up.
Step 3 With the metal carrier aligned in the slot
guides (see Figure 1), briskly slide the card
into the card slot until you feel it seat in
the backplane connectors.
Step 4 Tighten the captive screws.
Note The captive screws provide grounding for
the electromagnetic interference (EMI)
shielding.
Figure 1 Installing the Card in the Chassis
Note The cable interface line card insertion and
removal method is the same for all the
Cisco uBR7200 series routers.
Cabling
•Cisco uBR-MC16U—Green tabs
•Cisco uBR-E-16U—Slate blue tabs
•Cisco uBR-MC16X—Yellow tabs
Figure 2 Cisco uBR-MC16U
95800
US1
US2
US3
US4
US5
US6
US7
DS0-RF
DS1-RF
uBR-MC28U
DS
uBR - MCI6E
US
US
US
US
US
US
0
1
2
3
4
5
ENABLED
95801
uBR - MC16E
US0 US1 US2 US3 US4 US5
DS
ENABLED
Cabling the Cisco uBR-MC16U/E-16U
The Cisco uBR-MC16U/E-16U cable interface line
card has an onboard upconverter. To cable the
card:
Step 1 Connect the downstream cable to the
downstream (DS) port.
The RF downstream port rings and end
tabs are green for uBR-MC16U (see
Figure 2) and slate blue for uBR-E-16U.
Step 2 Connect the upstream cables to the
upstream ports (US0—US5).
Cabling the Cisco uBR-MC16X
The Cisco uBR-MC16X cable interface line card
(not supported on Cisco uBR7225VXR) does not
have an onboard upconverter. The card may
require up to 10-dB of attenuation due to a higher
IF output power (higher than legacy Cisco cable
interface line cards). To cable the card:
Step 1 Connect the downstream cable to the
downstream (DS) port on the card.
The IF downstream port ring and end tabs
are yellow. See Figure 3.
Step 2 Add RF attenuators as required to get the
correct IF output. Insert the attenuator
between the downstream IF output cable
and the upconverter. See Figure 3.
Step 3 Connect the upstream cables to the
upstream ports on the card (US0—US5).

Figure 3 Inserting an Attenuator
Note All upstream ports are light blue.
5 Removing the Card
To prevent the alarms from activating,
administratively shut down the card using the
shutdown command in interface configuration
mode before removing it from the chassis.
Step 1 Make sure that you are properly
grounded.
Step 2 Disconnect all the cables from the cable
interface line card.
Step 3 Unscrew the captive installation screws on
the faceplate.
Figure 4 Removing the Card from the Chassis
Step 4 Grasp the handle and carefully pull the
card out of its slot (see Figure 4).
uBR - MC16X
US0 US1 US2 US3 US4 US5
DS
ENABLED
95804
Upconverter
Attenuator
Cable
Connector
95802
US0
US1
US2
US3
US4
US5
US6
US7
ENABLED
DS0-RF
DS1-RF
uBR- MC28U
DS
uBR - MCI6E
US
US
US
US
US
US
0
1
2
3
4
5
ENABLED
Caution Always handle the cable interface line
card by the carrier edges and handle;
never touch the card's components or
connector pins.
Step 5 Place the card on an antistatic surface with
the component side facing up.
Note If the card is being returned to the factory,
immediately place it in a static shielding
bag and proper packaging for protection.
Caution For proper cooling and airflow,
always install a line card cover in an
empty line card slot.
6 Troubleshooting
Check the following:
1. Make sure that the card is securely seated in
the chassis.
If the captive screws do not tighten all the way,
the card is not properly seated in the chassis or
backplane. Carefully pull the card halfway out
of the slot, reinsert it, and tighten the captive
installation screws.
Caution A partially seated line card can cause
the router to reboot.
2. Are all enabled LEDs on?
If yes, the system is operational.
If no, check the following possibilities:
a. Verify that the card has been enabled and
configured for operation. The enabled
LED remains off when a card has not been
configured and enabled.
b. If a port is enabled but its corresponding
enabled LED is still off, check to see if the
card has pulled away from the backplane.
Reseat the card in its slot. (You do not
have to turn off the system power to do
this.) After the system reinitializes the
interfaces, the enabled LED on the card
should come on.
3. If the enabled LED remains off after the above
checks, it is likely that the system has detected
a processor hardware failure.
Contact Cisco TAC for further information
and help. To access the Cisco TAC website, use
the URL: http://www.cisco.com/tac
Figure 5 LEDs
7 Technical Specifications
Ta b l e 1 L E D s / S t a t u s
LED/Status Description
ENABLED—Green
ENABLED—Off
Card operating normally
Card not enabled
US—Green
US—Off
Upstream enabled
Upstream not enabled
DS—Green
DS—Off
Downstream enabled
Downstream not enabled
Ta b l e 2 Te c h n i c a l S p e c i f i c a t i o n s
Description Order Num/ Specifications
Cisco uBR-MC16U,
with upconverter
Cisco uBR-E-16U,
with upconverter
Cisco uBR-MC16X,
without upconverter
UBR-MC16U,
UBR-MC16U=
UBR-E16U, UBR-E16U=
UBR-MC16X,
UBR-MC16X=
95803
uBR - MC16E
US0 US1 US2
US3 US4 US5
DS
ENABLED
Downstream
LEDs
DS
Enabled LED
Upstream
LEDs
US0-US5
8 Related Documentation
•Cisco uBR7200Series Universal Broadband
Hardware Installation Guide
•Cisco uBR7200 Series Cable Interface Line
Card Installation Guide
•Cisco uBR7200 Series Software Configuration
Guide
•Cisco IOS CMTS Cable System Messages
Guide
•Cisco CMTS Feature Guide
For information about the 1–year warranty, see the
following URL:
http://www.cisco.com/en/US/products/prod_warra
nties_listing.html
Blank covers UBR-MC-COVER=
Weight—MC16U/
E-16U
Weight—MC16X
5.25 lbs (2.38 kg)
4.75 lbs (2.16 kg)
Power
MC16U/E-16U
MC16X
62 Watts (211.6 BTU/h)
47 Watts (160.4 BTU/h)
RF output power range—50 to 61 dBmV
Output—MC16U/
E-16U
Output—MC16X
+50 to 61 dBmV at RF
+42 dBmV at IF (+/-2 dB)
Modulation
Upstream (US0–US5) QPSK
8-, 16-, 32-, 64-QAM
Downstream (DS) 64-QAM, 256-QAM
Frequency range
Upstream
Downstream
5–65 MHz
70–860 MHz
The Cisco MC16 line card is compatible with
most cable systems worldwide, including but not
limited to Asia Pacific, Europe, and the Americas.
See Cisco IOS release notes for more information.
Table 2 Technical Specifications (continued)
Description Order Num/ Specifications