Citizen Miyota 9015 User manual

1. Setting movement on the movement holder.
Set movement as below pictures show. (* Movement holder is enclosed with the products.)
2. Setting the metal ring on the movement.
See below pictures and set the ring on boss of 1H/7H position. The dent of 3H stem position will be marker.
Note on setting 7H side at first when setting the ring. ( * The metal ring is enclosed with the product.)
Also, note on below point when you set the ring.
- Not to scratch on date dial (9015)
- Not to uplift or slip from movement.
Cal. 9015/90S5 Assembly manual
9015 Appearence
Oscilating weight side
Dent（7H）
Dent(1H）
7H side
1H side
Stem
Boss (7H）
①②③
④⑤ ⑥
stem position
After assembling
Boss (1H）
7H side 7H side
1H side 1H side
90S5 Appearence
Dial side
Dial side
1 / 3 Page

3. Assembling the dial.
a:) Put the dial on the metal ring.
b:) Install "screws for dial fixing" in the threaded hole on 2H/8H side of the movement,
and screw up tightly with pushing the dial from upper.
* Check below points
- Not to slip the dial from movement when the movement upside down after screwing up.
- Not to slip the metal ring from movement. (ref. below pictures)
4. Hand fitting.
a:) Push the crown back to A position (ref. Right figure)
Turn the crown clockwise over 10 times
and wind the mainspring.
b:) (9015)
Pull the crown out to C position
Turn the crown counter-clockwise,
and stop right after changing the date. *90S5: A=Mainspring winding / B=Time adjusting / C=N/A
C:) Fit each hands standing straight up as following order.
1 Hour hand
2 Minute hand
3 Second hand
D:) Check below points.
1 Turn the crown clockwise & counter clockwise,
and check each hands turning well.
2 Check the time of changing the date
whether the time is within your standard (9015).
3 Check the gap between hour hand and minute hand
when adjusting the time 12H position
whether the gap is within your standard.
OK NG
Metal ring is slipped and
floated.（Also dial is floated）
Fit each hands(H/M)
After screwing
12H
Push the dial from u
pp
er
2H Side
2H Side
8H side
screws for dial fixing
Mains
p
rin
g
windin
g
Date adjusting
Time adjusting
Position Figure(9015)
2 / 3 Page

5. Case fitting
a) Push the crown back to A position,
and pull out the interim stem as the following picture shows.
*The stem can be pulled out easily by pushing the button near the stem.
b) Clean inside the case by blowing the air into the case.
*Do not blow the air around the balance wheel of movement.
c) Fit the movement into the case by the following procedures.
d) Insert the stem slowly.
*Check the crown is set and stem length is correctly adjusted.
6. Plastic movement holder fitting (In the case of united holder)
Set the movement holder inside the case as the following picture shows.
Supplement）In the case of separated holder
a:) After matching stem position, and set the holder 1 from downward of the interim stem.
b:) Pulling out the interim stem, and fit the movement into the case.
b:) After matching stem position, and set the holder 2.
7. Fasten the caseback.
8. Check the running condition.
a) Confirm hands and case are not touching each other.
b) Turn the crown and confirm the calendar
and time setting can be done correctly.
Not to push around cock,
holder 1
holder 2
holder 1
holder 2
aaa
b c c
Push the button and pull
out the interim stem
3 / 3 Page