Citronic PL Series User manual

PL SERIES
DIGITAL POWER AMPLIFIERS
Order ref: 172.232UK, 172.238UK
User Manual

PL Series User Manual
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Features
Class H, 2-step architecture
Compact and light weight
High efficiency, high output
Independent dual-level clip limiters
Independent dual-level high-pass filters
Stereo, Parallel or Bridge Mono modes
Fully balanced signal path
Dual fan cooling
Soft-start on power up
Multi-level system protection
Introduction:
Thank you for choosing this Citronic Powerlite amplifier. This product has been designed to exacting standards to provide
accurate, immediate high power on demand whilst remaining very lightweight and compact for easy portability. The class
H architecture and innate protection circuitry are designed to provide reliable service for many years. Please, however,
read and follow these instructions to attain the best performance from this amplifier and avoid mis-use through incorrect
operation.
Warning:
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel
before further use.
Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside –Do not open the case –refer all servicing to qualified service personnel.
Safety
Check for correct mains voltage and condition of IEC lead before connecting to power outlet.
Ensure speaker leads are good condition with no short connections or damaged plugs
Check impedance of speaker loads do not exceed the minimum stated load for the amplifier
Do not allow any foreign objects to enter the case or through the ventilation grilles.
Placement
Keep out of direct sunlight and away from heat sources.
Keep away from damp or dusty environments.
When rack-mounting, ensure adequate support for the base of the amplifier and firm fixings for the front.
Ensure adequate air-flow and do not cover cooling vents at the front and rear of the amplifier
Ensure adequate access to controls and connections
Cleaning
Use a soft cloth with a neutral detergent to clean the casing as required
Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups
Do not use strong solvents for cleaning the unit.

PL Series User Manual
Front Panel
Rear Panel
Operation
Connect speaker cabinets to channel outputs using good quality leads and ensuring that the combined load on each
channel is no lower than 4Ω (for speaker loads connected from one to another, 8Ω + 8Ω = 4Ω).
Connect the left and right signal input from mixer or other line level source via the combo connectors on the rear panel
using good quality 6.3mm jack or XLR leads. If the signal is to be cascaded onto other amplifiers, connect these via the
XLR line level outputs.
Connect the amplifier to the mains outlet, making sure that the IEC lead is in good condition and connected securely.
For extra protection of speakers and amplifier, the CLIP LIMITER may be switched in to help prevent overload.
In some extreme cases, the operation of the clip limiter can be obtrusive. In these cases, disable the clip limiter and use
a dedicated compressor/limiter to control the high dynamics.
If the amplifier is not driving sub cabinets or is driving cabinets which cannot produce very low frequencies, the High
Pass Filters (HPF) may be switched in to avoid excessively low frequencies, which will not be able to be reproduced and
thus dissipate as heat, reducing efficiency. Settings for 30Hz and 50Hz are available.
Select the GAIN level of the input signals (standard is 26dB –may also be used to curtail the input level)
Select the mode in which the amplifier is to be used…
PARALLEL MODE sums both left and right input signals together and feeds the mono signal to both amplifier
outputs. This is useful when driving sub cabinets (which, in arrays, benefit from working together in mono) and
when each channel is powering speakers in different areas (avoiding one area hearing only left output and the
other only right). An LED (“PM”) shows when this mode is engaged
10. PM Parallel Mode indicator 5. SIGNAL indicators
11. BM Bridge Mono mode indicator 6. CH1 and CH2 level controls
12. CLIP indicators 7. Cooling vent
13. OUTPUT indicators 8. POWER switch
9. Mains inlet - IEC 15. CLIP LIMITER switch
10. CH2 output 16. GAIN input level selector
11. Bridge mono output 17. MODE switch (Parallel/Stereo/Bridge)
12. CH1 output 18. CH1 and CH2 High Pass Filters (HPF)
13. Cooling vent 19. GROUND LIFT switch
14. Combo signal inputs (XLR or jack) 20. Signal line outputs (XLR)

PL Series User Manual
STEREO is the normal mode of operation where each input is delivered to each output independently
BRIDGE mode couples both amplifier sections together to deliver the full rated power to a single output. The
minimum impedance is 8Ω in this mode. An LED (“BM”) shows when this mode is engaged
The GROUND LIFT switch disconnects signal ground (or “earth”) from mains ground. In certain cases, it may help to
alleviate mains hum –otherwise, leave ground connected to mains ground.
With CH1 and CH2 level controls turned fully down, switch on the power to the amplifier. This product has a “soft-start”
function which makes some checks before engaging power to the amplifiers, which may take a few seconds.
With mixer (or other signal source) levels turned down, gradually increase the amplifier’s CH1 and CH2 level controls to
the required level (normally full) and then gradually increase the signal level from the mixer until sound can be heard
through the speakers and then up to the required level.
During use, the LED indicators will show if a signal is present, if half output is being produced and if the output is
reaching clip level. If the red CLIP LEDs illuminate more than very briefly, reduce the volume until they hardly light at all.
If the internal protection circuitry detects a fault in the speakers or amp, the amplifier will enter Protect Mode and the
OUTPUT LED(s) will illuminate on the front panel to show this. Switch the amplifier off and check the entire system
(including leads) before powering up again. If still in Protect Mode, seek advice from qualified service personnel.
Before powering down, turn CH1 and CH2 level controls fully down to avoid loud noises when switching off.
Specifications
PL3200
PL3800
Power supply
230Vac 50/60Hz (IEC, 15A max.)
Output: RMS @ 4Ω
2 x 1600W
2 x 1900W
Output: RMS @ 8Ω
2 x 915W
2 x 1100W
Bridge power: RMS @ 8Ω
3200W
3800W
Input impedance
20kΩ
Output circuit architecture
Class H, 2-step
Frequency response
5Hz –50kHz
S/N ratio
>111dB
>112dB
THD
0.05%
Circuit protection
Short-circuit, DC, overload, soft-start
Dimensions
88 x 483 x 389mm
Weight
10.5kg
Troubleshooting
No power light on front panel switch
Ensure IEC is connected to mains and mains is on and lead is in good condition
Power light is on but no other LEDs and not
output
Check input signal and connection leads
Ensure CH1 and CH2 level controls are not turned fully down
Power light and Signal LEDs are lit but no
output
Check speaker cabinets are not blown and are in good working order
Check speaker leads are in good condition and connected properly
OUTPUT LED is continuously lit and there is no
output
Switch off and disconnect from mains
Check speakers are in good working order and not shorted (using a multi-tester)
If still in Protect Mode, switch off again and refer to qualified service personnel
Output is very distorted and “CLIP” LEDs are
lighting
Check speaker impedance is not below rated Ohms
Turn down Input level from audio source
Switch GAIN at rear to a lower level
Turn down CH1 and CH2 level controls
Output is working but at very low level
Ensure input source is at line level
Increase input level from audio source
Turn up CH1 and CH2 level controls
Switch GAIN at rear to a higher level
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2013. AVSL Group Ltd.