Clabel CT320D User manual

UNPACKING CHECKLIST
1
Printer
Data cable Installation Guide
Installation

APPEARANCE COMPONENT
2
Front view Back view
Top view
Left view

BT ERROR
1 Bluetooth indicator
2 Error indicator
3 Pause button
4 Paper advance button
5 Power indicator
7 Network port
8 Power supply connector
6 USB connector
9 Power switch
The interface shown above is for reference only as the interface
may vary depending upon the customer’s choice

Rubber roller
Paper compartment
Printhead
Paper tightener

CONSUMABLES INSTALLATION
3
1、 Use thumb to press the cover release button and
open the compartment cover.

2、Remove the label spindle and stopper and
set the paper roll into the label spindle.
1 2
3 4 5
Load the paper roll set into the printer
from top to bottom.

FCC Warning Statement
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority tooperate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device,pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.This equipment generates uses and can radiate radio frequencyenergy and,if not
installed and used in accordance with theinstructions, may cause harmful interference to radio
communications. However,there is no guarantee that
interferencewill not occur in a particular installation. If this
equipment doescause harmful interference to radio or television reception,whichcan be determined
by turning the equipment off and on,the user isencouraged to try to correct the interference by one
or more of thefollowing measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different. from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be co-located
oroperation in conjunction with any other antenna or transmitter.
RF Exposure Statement
--To maintain compliance with FCC's RF Exposure guidelines,This equipment should be installed and
operated with minimum distance of 20cm the radiator your body.
--This device and its antenna(s)must not be co-located or operation in conjunction with any other
antenna or transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

4、Adjust the tightener on the right until the label
paper is properly tightened.
5、Close the compartment cover.
Tighten inward.
Press down on the compartment cover.
When printing receipts, remove the label spindle and stopper and load
the paper following steps 4 to 5.

KEY FUNCTION
4
Switch to I
Switch to O
X
X
X
X
X
Press
X
Press
X
X
Press
Press
Press and hold
Switch to I X X Printer power-on
Printer power-off
Pause/continue printing
Advance a piece of paper
Print self-test page
Power switch Pause button Paper advance
button Function description
Switch label/bill mode
Switch to I Press and holdX
Switch to I XX Printer power-on
Switch to O XX Printer power-off
X XPress Invalid
X PressX Advance paper by 10 mm
X Press and holdX Advance paper until release
X PressPress Print self-test page
Power switch Paper advance
button
Pause button Function description
Switch label/bill mode
Label mode
Receipt mode

DESCRIPTION OF
INDICATOR LIGHTS
5
Flashing Out of paper
On constantly Top cover open
X Printer power-on
X Pause
Blinking Allow the overheated
printhead to cool down
X Bluetooth not connected
X Bluetooth connected
X
X
X
X
Blinking
Off
On constantly
X Off
X
X
On constantly
Flashing
X
X
X
X Printer ready
Bluetooth
indicator Error indicator Power indicator Indication
The indicator may vary depending upon the printer model.

SOFTWARE DOWNLOAD
6
iOS / Android
Visit https://ga.ctaiot.com/pc
Download “ Clabel trade ” and driver.
Please check the software usage in the software help center
Window
Scan the QR code below with a mobile phone to
download “ Clabel trade ”.
Please operate the software follwing the software guidance.
Download label editing app "Clabel trade"
from Google Play Store or Apple APP Store
and install it.
Clabel trade

NOTES
7
Usage precautions
(1) Install the printer on a stable surface. Do not place the printer in areas exposed to
vibration or impact.
(2) Do not use or store the printer in areas exposed to high temperatures, high humidity,
or excessive dust.
(3) Connect the power adapter to an appropriate grounding outlet. Avoid using the
same outlet with large motors or other devices that may cause power supply voltage
fluctuations.
(4) No water or conductive substance (i.e., metal) is allowed into the printer. In case of
such a condition, turn off the power immediately.
(5) Do not allow the printer to start printing when there is no recording paper installed,
otherwise the printhead and rubber roller will be damaged.
(6) Disconnect the DC adapter when the printer is not used for a long time.
(7) Users shall not disassemble the printer for maintenance or modification.
(8) Use only the power adapter that comes with the printer.
(9) To ensure print quality and normal lifetime, use recommended or good quality
paper.
(10) Shut down the printer when connecting or disconnecting interface connectors.
(11) As the power disconnecting device, the power plug of the adapter should be
installed near the equipment and easy to access.
(12) This product is intended to be used at altitudes not exceeding 5,000 m in tropical
climates.

Printer cleaning
Note
The printhead should be cleaned promptly if:
(1) The print is not clear;
(2) The vertical column of print is not clear;
(3) A Grinding noise is heard while feeding the paper;
Cleaning Steps:
(1) Switch the printer power off, open the cover and remove any paper;
(2) Allow the printhead to cool if it had just finished printing;
(3) Using a soft cotton cloth dipped in absolute ethyl alcohol, gently wipe the dust
and particles off the thermal printhead surface;
(4) Only use the printer for printing until the cleaning alcohol evaporates
completely and the cover is closed;
(1) Make sure to turn off the printer before any maintenance.
(2) Do not touch the printhead surface with the fingers or metallic objects. Do not
abrade the printhead, rubber roller, and sensor surface with tweezers or other tools.
(3) Do not use gasoline, acetone, or any other organic solvents for cleaning.
(4) Only use the printer for printing until the cleaning alcohol evaporates
completely.

Label Printer
Quick Installation
Guide
Shenzhen Dudian Technology Co., Ltd.
Room 1101, Building 3, COFCO Chuangzhi Factory Area, District 67,
Xingdong Community, Xin'an Street, Bao'an District, Shenzhen.
CT320D