Clair de Lune Deluxe Rocking Stand User manual

Tools
Requ
Deluxe Rocking Stand
IMPORTANT: Please read before assembling
!
In the unlikeley event that you should nd any component missing from your stand please call our helpline and
replacements will be forwarded by return.
Never assemble or use a stand with missing or broken parts.
Ensure that your stand is always secure and tighten all screws full, but do not over tighten as this can make it insecure.
Please assemble with a hand held screwdriver and not a cordless drill as this can lead to over tightening of the screws.
Before rst use of the rocking stnad please check to ensure that all screws are tightened securely.
It is important that the stand is checked regularly during continued use to ensure that all the screws remain secure.
02.2020 V2

A x 2 Bx2
E x 2
C x 1
Fx1
Gx2
Components
50mm
x 8
40mm
x 8
15mm
x 4
IMPORTANT: Please make sure when assembling the stand that the pre-drilled guide holes in each
component are lined up and that the screws are located carefully into the holes before
tightening them up.
16mm
x 2
18mm
x 2
Hx2
Dx1
Safety
Tools
Required
Flathead
screwdriver
Phillips head
Size 2 (PH2)
screwdriver
To prevent damaging
the screws during
assembly, please ensure
you use the right size
and type of screwdriver
Pozidriv®
Phillips
This product is suitable only for a child who cannot sit up unaided, roll over and
cannot push itself up on its hands and knees. Maximum weight of the
child: 9 kg
WARNING: Only use on a rm ground which is horizontal, level and dry
WARNING: Do not let other children play unattended near the carry cot and stand
WARNING: Do not use if any part of the stand is broken, torn or missing
WARNING: Do not attach anything to the stand, which may aect its stability
Only use replacement parts supplied or approved by the manufacturer
Do not place the stand near an open re or other source of strong heat
When the stand is not in use, it shall be stored away from children
If the mattress is purchased seperately, it shall t well into the product and the depth
from the top of the side of the product should be less than 170mm (200mm if to be
used with a stand) when the mattress is in position of use
The stand is designed for use with a palm or wicker moses basket of min/max
700-835mm in length and 300-370mm in width.
Do not add another mattress on top of the mattress provided or recommended
by Clair de Lune
CLEANING INSTRUCTIONS
Stand - If necessary, wipe with damp cloth
Dispose of all packaging safely before use. Complies with BS EN 1466: 2014
Clair de Lune, Shentoneld Road, Sharston Industrial Estate
Wythenshawe, Manchester M22 4RW - 0161 491 9800 / [email protected]
IMPORTANT - PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE.
IN ORDER THAT THE STAND YOU HAVE PURCHASED MAY BE SAFELY USED THE FOLLOWING INSTRUCTIONS MUST BE FOLLOWED.
WARNING: KEEP THE PLASTIC BAG AWAY FROM CHILDREN TO AVOID SUFFOCATION.

3
40mm
40mm
40mm
40mm
40mm
40mm
40mm
40mm
A
B
A
B
E
E
F
1. Align the two sides of rocking stand so that the recesses for dowels
E in the uprights face each other.
2. Locate the 2 bottom dowels E into the lower recesses in uprights
A/B, secure using 4 x 40mm screws.
3. Locate strap & dowel assembly F into the upper recesses in uprights
A/B, secure using 4 x 40mm screws.
!
Important: Make sure
dowels are pushed fully
into dowel recesses.
!
Important: Ensure that the staples securing straps to dowels of the strap &
dowel assembly E are facing downwards.
21. Using 2 x
16mm screws,
affix circular
stabilisers H to
inner holes at
either end of D.
2. Screw 2 x
18mm barrel
screws to outer
holes at either
end of D.
D
1
50mm x 2
50mm x 2 50mm x 2
50mm x 2
Note: the uprights A and B should curve inwards towards each other with the larger recessed
dowel holes facing the same way.
1. Using 4 x 50mm screws, fasten 1 x A and 1 x B uprights to 1 x base rocker C through the holes in
the base of C. The pre-inserted dowel in A and B will slot into the middle of the 3 holes in C.
2. Repeat with the second set of parts A, B and D.
A
A
B
DC
B
!
Important: Ensure holes
for stabiliser in rocker D
are facing same way as
recesses in uprights A
and B.

I
ers
d is
4
G
G
15mm x 1
15mm x 1
15mm x 1
15mm x 1
IMPORTANT: Ensure the moses basket is held securely by the end straps. Use the 3 holes on the
end straps to provide adjustment. Check carefully that the moses basket is secure in
the rocking stand before use.
Align the holes in the flexible straps G with the gold star-
shaped fittings on the inside of the uprights A/B on both
sides. Secure using 4 x 12mm screws. 5
Locked
Unlocked
!
Important: Stabilisers
must be in locked
position when stand is
unattended.
AFTER FIRST USE PLEASE RE-CHECK TO ENSURE THAT ALL SCREWS ARE TIGHTENED SECURELY