Clare Controls Schlage BE369 Quick start guide

Doc ID - 1234 • Rev 10 1 / 24
Schlage Z-Wave Door Locks
Integration Notes
For all models
Content
Preface...1
Introduction...1
Supported models...2
Installing and programming Schlage door locks...2
Pairing, configuring, and removing the Schlage...2
Pairing and removing the door lock with Fusion...16
Creating rules with the Schlage door lock...21
Using the door lock in the ClareHome app...24
Contact information...24
Last modified: 06/21/19
Preface
For information on Z-Wave and ClareHome, see Installing Z-Wave with
ClareHome.
Notes
•When installing Z-Wave devices, ensure that there is nothing inhibiting their
signal. Z-Wave relies on radio signals. Metal or thick walls may limit their
signal strength.
•We recommend having 2 or more repeating Z-Wave devices that support
beaming.
Introduction
Schlage Z-Wave door locks integrate with ClareHome via the Z-Wave network.
Installers only need to pair (add) the unit into the ClareHome. The Schlage locks
provide real time lock status indications.
By integrating the Schlage into the ClareHome control system, your customers
can control the door lock from their Android or iOS devices.

Doc ID - 1234 • Rev 10 2 / 24
Supported models
The following Schlage models are supported.
•BE369
•BE468NX
•BE469NX
•FE599NX
Note: The B3369, BE468NX, and BE469NX are manufacturer discontinued
(12/2018). These locks are Clare Supported.
Installing and programming Schlage door locks
Only qualified installation technicians should install Schlage door locks. Follow
the installation and programming instructions that came with your Schlage
equipment. We recommend that you pair the lock with the ClareHome Z-Wave
controller before installing it in the door.
Notes
•The door lock must be within 6 feet of the controller to pair.
•The door lock is configurable using the Clare app, the Clare Controls Install
Assist app, and Fusion.
Pairing, configuring, and removing the Schlage
After installing the door lock, pair it.
To pair the door lock using ClareHome or Install Assist:
1. Access the Clare Controls Install Assist app, and then tap Add Devices.
–or –

Doc ID - 1234 • Rev 10 3 / 24
Access the ClareHome Menu, and then tap Add/Edit Devices.
2. At the bottom of the screen, tap the plus icon .

Doc ID - 1234 • Rev 10 4 / 24
3. Tap Access.
4. Tap Z-Wave Device - Access.
5. Tap Start Discovery Mode, and then pair the device as per the
manufacturer’s instructions.

Doc ID - 1234 • Rev 10 5 / 24
6. Enter a name for the door lock, and then select an area.
7. Tap outside of the area drop-down and the door lock automatically saves.
8. Continue to set or remove Personal Identification Numbers (PINs) for the door
lock.

Doc ID - 1234 • Rev 10 6 / 24
To add a door lock PIN:
1. Access the Menu , and then tap Add/Edit Devices.
2. Tap Access, and then select the desired door lock.

Doc ID - 1234 • Rev 10 7 / 24
3. Enter an ID number, and then enter the desired door lock code.
Note: Each door lock has a set number of usable IDs and PIN codes. Read
your device’s documentation to find out how many IDs are supported and the
available format of the PINs.
4. Tap Save Code.
Once the code is saved, the code is functional on the door lock.
Note: For scene, schedule, notification, and automation configuration, see
ClareHome App Guide (DOC ID 1750).

Doc ID - 1234 • Rev 10 8 / 24
To remove a door lock PIN:
1. Access the Menu , and then tap Add/Edit Devices.
2. Tap Access, and then select the desired door lock.

Doc ID - 1234 • Rev 10 9 / 24
3. Enter an ID number, and then tap Remove Code.
Note: The ID number is a user number with an assigned access code.
A success message displays, the code is no longer associated with the door
lock.

Doc ID - 1234 • Rev 10 10 / 24
To remove all door lock PINs:
1. Access the Menu , and then tap Add/Edit Devices.
2. Tap Access, and then select the desired door lock.

Doc ID - 1234 • Rev 10 11 / 24
3. Tap Remove All Codes.
A success message displays. Only the master code remains associated with
the door lock. All other codes are removed.

Doc ID - 1234 • Rev 10 12 / 24
To see if here is an existing PIN associated with a user ID:
1. Access the Menu , and then tap Add/Edit Devices.
2. Tap Access, and then select the desired door lock.

Doc ID - 1234 • Rev 10 13 / 24
3. Enter the desired ID in, and then tap Get Code.
If the ID has a PIN associated with it, a redacted code appears in Door Lock
Code field.
If there is not PIN associated with that ID, an available banner displays
denoting that the ID is usable.

Doc ID - 1234 • Rev 10 14 / 24
To remove the door lock using ClareHome or Install Assist:
1. Access the Clare Controls Install Assist app, and then tap Add Devices.
–or –
Access the ClareHome menu, and then tap Add/Edit Devices.

Doc ID - 1234 • Rev 10 15 / 24
2. Tap the dots in the upper-right corner.
3. Tap Unpair Z-Wave Device.

Doc ID - 1234 • Rev 10 16 / 24
4. Tap Start Removal Mode, and then remove the device as per the
manufacturer’s instructions.
Note: Press and hold the same button used in pairing the device to remove
the device.
Pairing and removing the door lock with Fusion
Before installing the door lock, pair it.
Note: The BE469NX/BE468NX may have pairing connectivity errors and require
more than one pairing attempt. In some cases, the BE469NX/BE468NX door lock
requires a factory reset.
To complete a factory reset on the BE469NX/BE468NX, hold down the Schlage
button on the lock while connecting the batteries. This resets the door lock and
restores the lock’s ability to pair.
To pair the door lock with Fusion:
1. Access your project, and then click the Z-Wave Wizard icon .

Doc ID - 1234 • Rev 10 17 / 24
2. Click on Z-Wave Devices.
3. Select the device’s location, and then enter a name for the device.
Notes
•We recommend naming the device after its location to avoid confusion.
For example, Entryway Door Lock.

Doc ID - 1234 • Rev 10 18 / 24
•If you want to add an area, click the green plus icon , enter a name
for the area, and then click Add Area.
4. Click Add It!.
The Z-Wave adding mode dialog displays.
5. Refer to installation instructions that came with your Schlage device to pair.
Note: This varies by device.

Doc ID - 1234 • Rev 10 19 / 24
6. The door lock appears in in the added devices list.
7. Click the Summary tab to view all Z-Wave Wizard added devices and their
status.
8. Click the Close Window icon in the top-right of the wizard to exit and
return to the Devices tab.
Note: The Z-Wave devices added with the Z-Wave Wizard are automatically
imported on the Devices tab.

Doc ID - 1234 • Rev 10 20 / 24
To remove the door lock with Fusion:
1. Access your project, and then click the Z-Wave Wizard icon .
2. Click on Unpair a Device.