Clear One UNITE 260 Pro User manual

UNITE® 260 Pro Camera
Quick-Start Guide
QSG-0158-001v1.0 January 2023

Unite 260 Pro Camera
Page 1 QSG-0158-001v1.0 January 2023
Quick-Start Guide
Notices
© 2023 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice.
Document: QSG-0158-001v1.0 January 2023
ClearOne®Contacts
Headquarters Headquarters
5225 Wiley Post Way Suite 600 Tel: +1.801.975-7200
Salt Lake City, UT 84116
Sales Technical Support
Tel: [phone] Tel: [phone]
[email protected] [email protected]
Important Safety Information
1. Before you set up the camera, read this manual carefully. Follow the setup instructions indicated
in this manual.
2. Keep this manual for future use.
3. To prevent electric shock, do not remove screws or the camera housing. No self-serviceable
parts are inside the housing
WARNING: TO
PREVENT FIRE
OR
ELECTRICAL
SHOCK
HAZARD, DO
NOT EXPOSE
THIS
PRODUCT TO
RAIN OR
MOISTURE
THE LIGHTING FLASH
AND ARROWHEAD
WITHIN THE TRIANGE IS
A WARNING SIGN
ALERTING YOU OF
DANGEROUS VOLTAGE
INSIDE THE PRODUCT.
THE EXCLAMATION POINT
WITHIN THE TRIANGLE IS A
WARNING SIGN ALERTING
YOU OF IMPORTANT
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
SEE MARKING ON BOTTOM/BACK OF PRODUCT
RISK OF ELECTRIC SHOCK DO
NOT OPEN
AVIS RISQUE DU CHOC ELECTRIQUE
- NE PAS OUVRIR
Use only in
non-tropical
locations.
Use only at
altitudes of
2000 meters
or less.
CAUTION

Unite 260 Pro Camera
Page 2 QSG-0158-001v1.0 January 2023
Quick-Start Guide
Packing List
Verify that you have received all parts associated with each of the components.
Inspect your shipment carefully. If the shipment shows obvious signs of damage, retain original
boxes and packing material for inspection by the carrier, and contact them immediately. ClearOne is
not responsible for product damage incurred during shipment.
No Product Description Product Model
1 Unite 260 Pro Camera
2 Remote
3 USB Cable
4 AC Adaptor & Power Cord
5 RS232 Cable

Unite 260 Pro Camera
Page 3 QSG-0158-001v1.0 January 2023
Quick-Start Guide
Setup
Installation
This product should be placed on Wall mount or Celling Mount. Avoid contact with any liquid, gas or
solid material that may cause corrosion.
Step 1
Refer to the diagram below to make sure the connections are correct.
Step 2
Connect to the power, can be by PoE (48V DC), or 12V DC power supply.
Step 3
On the back panel of the UNITE 260 Pro, set the Power Switch to On. The LED light on the front
panel indicates the camera is powered on.
Step 4
The process of initialization is complete after the camera pan-tilt rotates to the maximum position of
top right and returns to the center.
Note: If the position preset 0 has been stored, the position preset 0 will be called up after
initialization.
Note: When the camera is connected, it will appear as a microphone device. The camera only
provides audio if you plug 3.5 mm analog line in connector.

Unite 260 Pro Camera
Page 4 QSG-0158-001v1.0 January 2023
Quick-Start Guide
Remote Control
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
3

Unite 260 Pro Camera
Page 5 QSG-0158-001v1.0 January 2023
Quick-Start Guide
No. Name Function Description
1Standby Key On/Off
2Number Key Preset setting or transfer preset
3*Key For use with other keys
4Preset Key Preset: Setting Preset + Number key(0-9)
5HOME key Confirm selection or press to turn PTZ back to the
middle position
6Return Key Return back to the last menu level
7Zoom Keys Moving between wide/narrow angle lens modes,
slowly or quickly
8L/R SET Key Standard: Simultaneously press L/R SET key + 1
Reverse: Simultaneously press L/R SET key + 2
9Focus Keys Auto/Manual/Far-end/Near-end focus
10 CAMERA SELECT Keys Select the camera to control
11 #Key For use with other keys
12 IR Remote Control Key [*+#+F1/F2/F3/F4]: NO.1/2/3/4 address
13 Reset Key Delete preset: [RESET] + Number key (0 – 9)
14 PTZ control keys After zoom, press to move the PTZ
15 Menu Key Used to enter/exit OSD Menu
16 BACKLIGHT Key Turn on/off backlight
17 P/T RSTkey For use with PTZ cameras
Shortcut Set Tracking mode/Short press to stop Auto Framing or
Auto Tracking
[*] + [#] + [1]: OSD menu default English
[*] + [#] + [3]: OSD menu default Chinese
[*] + [#] + [4]: Display current IP address
[*] + [#] + [6]: Quickly recover the default
[*] + [#] + [8]: Display the camera version
[*] + [#] + [9]: Quickly set up inversion
[*] + [#] + [MANUAL]: Restore to default IP address.
Functionality for F1 and F4
Short press F1 to start Auto Framing, and short press F4 to pause or start, and long press F4 to
close Auto Framing.
No. Function Button
1 Auto framing ON (F1)
OFF (F4)
2 Auto tracking On (F3)
OFF (F4)

Unite 260 Pro Camera
Page 6 QSG-0158-001v1.0 January 2023
Quick-Start Guide
Troubleshooting
Image
Image is jittery when the camera is properly connected:
1) Ensure that the camera is installed in a stable position.
2) Remove vibrating objects/machinery from the proximity of the camera.
Control
Remote control not operating
1) Check/replace batteries in the remote control unit.
2) Ensure the camera working mode is correct.
Safety Precautions
Installation
This product should be placed on a smooth flat surface, or bracket-mounted, if desired. Avoid
contact with any liquid, gas or solid material that may cause corrosion.
Do Not Disassemble
This product has no user-repairable parts. Damage caused by unauthorized disassembly is not
covered by warranty.
Notice
Electromagnetic fields at specific frequencies may affect image quality.