Clenergy PV-ezRack SolarRoof IS-SR265/111 User manual

1/10 Duerdin Street, Clayton VIC 3168 Australia
Tel: [phone] Fax: [phone]
E-mail: [e-mail] www.clenergy.com.au
PV-ezRack SolarRoof Isolator Shade
Installation Guide
NO.: PZ15-IM02-10
Contents
1 Introduction .............................................................................................1
2 Tools & Components................................................................................2
3 System overview .....................................................................................3
4 Installation Instructions ...........................................................................4

1/ 4
1/10 Duerdin Street, Clayton VIC 3168 Australia
Tel: [phone] Fax: [phone]
E-mail: [e-mail] www.clenergy.com.au
1. Introduction
Clenergy PV-ezRack SolarRoof Isolator Shade is the latest accessory for roof-
top PV-mounting system. With full-covering bracket design and our patented Z-
Module technology, our Isolator Shade is easily installed along the Rail and
provides full covering for the Isolator.
Please review this manual thoroughly before installing PV-ezRack SolarRoof
Isolator Shade.
The installer is solely responsible for:
•Complying with all applicable local or national building codes, including
any that may supersede this manual;
•Ensuring that PV-ezRack and other products are appropriate for the
particular installation and the installation environment;
•Using only PV-ezRack parts and installer-supplied parts as specified by
the PV-ezRack project plan. (substitution of parts may void the
warranty and invalidate the letter of certification);
•Recycling according to the local relevant statutes.
•Removal by reversing the installation process.
•Ensure that there are no less than two professionals working on panel
installation.
•Ensure the installation of related electrical equipment is performed by
licenced electricians.
•Ensuring safe installation of all electrical aspects of the PV array. This
includes adequate earth bonding of the PV array and PV-ezRack®
components as required in AS/NZS 5033-2014 AMDT 2 2-2018.

2/ 4
1/10 Duerdin Street, Clayton VIC 3168 Australia
Tel: [phone] Fax: [phone]
E-mail: [e-mail] www.clenergy.com.au
2. Tools and Components
2.1 Tools
Marker
Screw Driver
( for M8 Hexagon
Socket Screw)
Screw Driver
(6mm）
Torque Wrench
Note: the tools above are not included in Clenergy’s supply scope.
2.2 Components
IS-SR265/111
Isolator Shade
IS-SR265/111/B
Isolator Shade, Black
anodized

3/ 4
1/10 Duerdin Street, Clayton VIC 3168 Australia
Tel: [phone] Fax: [phone]
E-mail: [e-mail] www.clenergy.com.au
3. System Overview
3.1 Overview of PV-ezRack SolarRoof Isolator Shade
3.2 Precautions during Stainless Steel Fastener Installation
Improper operation may lead to deadlock of Nuts and Bolts. The steps below
should be applied to every stainless steel nut and bolt assembly to reduce this
risk.
3.2.1 Reduce the friction coefficient:
（1）Ensure that the thread surface is clean (no dirt or contaminant)
（2）Apply lubricant (grease or 40# engine oil) to fasteners prior to tightening
to avoid galling or seizing of threads;
3.2.2 General installation instructions:
（1）Apply force to fasteners in the direction of thread
（2）Apply force uniformly, to maintain the required torque
（3）Professional tools and tool belts are recommended
（4）Avoid using electric tools for final tightening
（5）Avoid working at high temperatures
3.2.3 Safe Torques
Please refer to safe torques defined in this guide.
Isolator Cover
Isolator Bracket
Isolator

4/ 4
1/10 Duerdin Street, Clayton VIC 3168 Australia
Tel: [phone] Fax: [phone]
E-mail: [e-mail] www.clenergy.com.au
4. Installation Instruction
According to your plan, mark out
the position on the Rail for Isolator
Shade Installation.
Note：Allow an extra 265 mm of
Rail length for Isolator Shade
installation. Allow space above the
Rail for Isolator Shade opening.
-- Rotate up the Cover and fix the
Isolator to the Isolator Shade
according to the Isolator Installation
Guide.
-- Once the Isolator is fixed to the
isolator shade, position the Z
Module in the Rail channel and fix
the Shade with the bolt supplied.
Recommended torque is 4-5 Nm.
- The completed installation with
the mounted Isolator is shown in
the figure on the right.