ClimateRight easyair CR12000SACH User manual

Operating and Servicing Instructions
MINI SPLIT
AIR CONDITIONER & HEATER
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE
Read and follow all safety rules and instructions
before operating this equipment.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.
Please keep this manual for future reference.
Air Conditioner & Heater
ClimateRight®USA
Questions or concerns? For assistance, please call Customer Service
777 Manor Park Drive • Columbus, OH 43228
www.climateright.com
Ph: 800-725-4628
OWNER’S MANUAL
CR12000SACH

INTRODUCTION
TABLE OF CONTENTS PRODUCT SPECIFICATIONS
Evaporator (indoor unit)
Condenser (outdoor unit)
Remote Control
CLIMATERIGHT CR12000SACH Mini-Split Air Conditioner and Heater
Thank you for choosing ClimateRight. This owner’s manual will provide you
with valuable information necessary for the proper care, installation, and
maintenance of your new product. Please take a few moments to thoroughly
read the instructions and familiarize yourself with all the operational aspects of
your new ClimateRight Mini-Split Air Conditioner and Heater.
For your records, please attach a copy of your sales receipt to this manual.
Also, write the store name/location, date purchased, and serial number below:
Store Name: _________________________________________________________
Location: ___________________________________________________________
Date Purchased: ______________________________________________________
Serial Number: _______________________________________________________
Introduction & Contents .............................................
Safety Instructions .....................................................
Product Description ...................................................
Assembly Instructions ............................................
Troubleshooting .........................................................
Limited Warranty ........................................................
Remote Control Operation ..........................................
1
2
3
4
5 & 6
7 & 8
9
10
1 2
PACKAGE CONTENTS:

SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS FOR USING YOUR
Mini Split Air Conditioner and Heater
WARNING: TO REDUCE THE
RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
• Fully assemble before operating.
• Do not repair or modify the unit unless
All other repairs should be completed by
• The plug for this unit is polarized with one
blade wider than the other. Do not force the
plug into an electrical outlet. Do not alter
the plug in any way. If the plug dose not
to install a proper outlet.
• Do not use if the power cord or plug is
damaged or the connection to the wall
outlet is loose.
lower back of the unit.
• Do not damage, break, forcefully bend,
pull, twist, bundle, coat, pinch, or place
heavy objects on the power cord.
• Periodically remove dust from the power
plug.
• If the power plug is damaged, it must be
technician
• Remove the power plug from the outlet
before cleaning the unit. When removing
the power plug, grasp by holding the plug
itself, never hold by the cord.
• Remove the power plug from the outlet
when not in use.
• Do not handle the power plug with wet
hands.
• Do not operate the unit when using indoor
smoke-generating insecticides.
• Do not clean unit with benzene or
paint thinner. Do not spray
insecticides on the unit.
• Do not use the unit where it is
humid or where the unit may b
come wet, such as in a bathroom.
objects into the air intake or outlet.
gases. Do not use near cigarettes,
incense, or other spark-creating
items.
• Unit will not remove radon or
carbon monoxide emitted from
heating appliances or other sources.
• Do not block the air intake or air outlet
vents. Ensure that there is proper
• Do not use near hot objects, such as
• Do not use where the unit may come
into contact with steam.
• Do not use the unit on its side.
• Do not install where the air outlet will
• Keep away from products that
generate oily residue.
• Keep children and pets away from
the product.
• Always unplug the unit before
cleaning or servicing.
• Use of an extension cord is not
recommended as it could prevent the
unit from operating normally and could
potentially pose a fire and safety risk.
It is recommended that unit is located
near a 3-prong 115V GFCI outlet. If
one is not available, a qualified
electrician should install one.
!!
3 4
PACKAGE CONTENTS
Interior Fan / Control Unit
Exterior Condensor Unit
Installation Parts and Accessories

ASSEMBLY INSTRUCTIONS
5 6
Tools needed for installation:
Stud Finder Tape Measure Level
Pencil 6 – 2” Wood Screws Wall Clamps
Drill with Drill Bits Step Ladder 2-¾” hole saw
1) Determine best location for wall mounted evaporating unit
cation with
a pencil.
3) Remove the mounting bracket from the back of the evaporator unit using
a Phillips head screwdriver.
4) Position the mounting bracket on the wall that you just marked the studs and
move the bracket until the holes on the bracket align with the studs.
5) Place a level at the bottom of the bracket to ensure that the bracket is level.
6) Secure the bracket to the wall using the 2” wood screws.
7) As you are facing the wall where the bracket is mounted, using a 2-¾” hole saw,
cut a hole just the right lower corner of the bracket. This is where the refrigerant
lines, electrical wire, and drain line will pass through the wall. Drill this hole on a
slight downward angle to ensure proper drainage of the indoor unit.
8) Remove debris from inside of the hole.
9) In order to align the hole to the outside, drill through the exterior wall from the
inside. Center the drill bit in the hole as this will give you a more accurate hole
placement on the outside. Visibly note where the hole should be cut on the
outside by the drill. Center the hole saw around the mark and drill through
the exterior of the structure.
10) You are now ready to install the indoor unit. With assistance, uncoil the
refrigerant lines so that they are at a 90 degree angle from the unit.
11) Guide the refrigerant lines, electrical, and drain lines through the wall to
the outside.
12) Once you have successfully run the lines and wiring, you can now position
the evaporator unit so that the top can securely hook onto the mounting plate.
13) Push the bottom of the unit towards the wall until you hear the unit snap onto
the mounting plate.
14) The interior installation is now complete.
16) Carefully bend the lines downward, routing them to the left or right as
needed to connect to the condenser portion of the unit making sure
that the drain line is in a downward position and the stream is
directed to a proper location.
clamps or gutter down spouting, either of which can be purchased at
your local hardware store.
18) Position the condenser unit on the pad ensuring that the back of the
unit is at least 12” away from the structure and within reach of the
lines coming from the inside unit and a power outlet.
secure the condenser unit to the pad with screws through the feet
of the unit.
can proceed with connecting the refrigerant line to the condenser unit.
21) Remove the shipping plug from the refrigerant line. There may be
some slight pressure when you remove the plug, so be careful. Plug
the refrigerant lines to the condenser. Push the plug into the
ce.
22) Connect the outdoor quick cable coupler with the indoor quick cable
connector and secure the green ground wire to the unit with a
single screw.
23) Fill in the gaps left over by the pipeline hole and wall hole to prevent
rain water from entering.
24) Plug in the power supply cord to the CGFI outlet. The unit is now
ready for operation.
ASSEMBLY INSTRUCTIONS (cont.)
15) For the exterior condenser unit, a pad or base is recommended. The
base can be made out of fiberglass material, stepping stones,
or you can choose to pour a concrete pad. Whichever you choose,
make sure that it is level.

TROUBLESHOOTING
7 8
Ensure proper ventilation and avoid anything that may obstruct operation
of the front of the indoor unit.
Do not install the unit near the following:
• Flammable gases
• Poisonous or sultry gases
• Seaside district exposed to sea breezes
• Air conditioner body and remote controller must be (39-3/4”) or
more away from a TV or a radio
Proper Installation Locations:
When installing the unit, choose a place which can stand the weight of the unit and
does not increase the operational noise or vibration. Avoid areas where there may
vibration-proof
• Avoid leaving items near the outlet and inlet of the outdoor unit. These can cause
malfunction or increase operation noise.
• Consult your ClimateRight Customer Service Representative if you continue to
hear irregular sounds during operation.
Inspection and maintenance:
-According to the service conditions and operating environment, the
inside of the air conditioner will become dirty after several seasons
(3 to 5 years) of service, resulting in decreased operating performance.
Inspection and maintenance are recommended annually in addition
to usual cleaning.
-We recommend performing inspection and maintenance during
off-season.
Power Cord Care:
• Do not rest anything on the power cord
• Do not place the Mini-Split Air Conditioner condenser where people or pets may
trip over or walk on the power cord
• Do not pick the unit up by the power cord
• Inspect the power cord before use to ensure the cord and plug are in
good condition
Self-Check Information Self-Check Codes Digital Self-Check
Codes
Defrost Indication Flicker 1 time/1 sec Indicates “dF”or
Anti-Cold Wind Flicker 1 time/1 sec Fan motor not running
Room Temp Sensor Fault Flicker 1 time/8 sec E2
Cold Temp Sensor Flicker 2 times/8 sec E3
Over-heat Protection Flicker 3 times/8 sec E8
Indoor Fan Fault Flicker 6 times/8 sec E5
External Feedback Fault Flicker 7 times/8 sec E7
Open the Door Fault Flicker 3 times/8 sec E0
Outdoor Tube Temp Flicker 4 times/8 sec E1
Communications Fault Flicker 6 times/8 sec E6
TROUBLESHOOTING

LIMITED WARRANTY
9 10
LIMITED WARRANTY
ClimateRight products (“ClimateRight”) are warranted by ClimateRight LLC, the
manufacturer, and the distributor of ClimateRight portable air conditioning and
-
ship and materials. ClimateRight portable air conditioners, heate
are warrantied to the original owner only, for one (1) year from the date of purchase
against manufacturer defects under normal use and service. This Warranty is not
transferable and applies only to original purchases and original purchase dates.
After the expiration of the Warranty term (1 year), the owner is responsible for all
costs associated with repair or troubleshooting.
HOW TO FILE A WARRANTY CLAIM:
email from an authorized ClimateRight representative. A web form is also available
at www.climateright.com to submit your claim as well. If ClimateRight LLC, at its
sole discretion, deems your Warranty claim valid, a prepaid shipping label will be
sent to the address provided for return of the climate right unit for inspection and
repair or replacement. In good faith, we will send you out a replacement unit before
receiving the defective unit back. If, during inspection, the unit has been found to
will be charged for the replacement unit plus shipping and handling fees and no
refund will be issued for the initial purchase. If the unit has been found to be de-
fective the original purchase price will be refunded.
Please note: Any damage caused by improper packaging of the return unit to the
authorized service center will void the warranty.
REMOTE CONTROL OPERATION
ON / OFF Turns the Breeze unit on or o
TEMP Press to raise or lower the temperature setting. Temperature
setting range is between 61˚ F and 86˚ F.
MODE Selects the operating mode. Select between COOL, HEAT, DRY,
FAN or AUTO.
COOL: the unit will operate as an air conditioner to maintain
the desired set temperature
HEAT: the unit will operate as a heat pump to maintain the
desired set temperature
DRY: the unit will operate as an air conditioner on low speed to
reduce humidity levels while not aecting the air temperature
as greatly.
FAN: the unit will operate as a fan to circulate air only.
AUTO: the unit will operate as an air conditioner or heat pump
to maintain the desired set temperature.
FAN SPEED Selectable speeds are LOW, MEDIUM, HIGH or AUTO. AUTO
will automatically adjust the fan speed to maintain proper set
point.
TIMER Press to set the timer for the unit to come on. Optional setting
only operates when“ON”icon is illuminated on remote.
TURBO TURBO mode operates the unit at maximum performance level
to bring the room to the set temperature as rapidly as possible.
Available in COOLING and HEATING modes.
SWING Press to turn on the SWING function or to set the desired angle
of the airow. (Airow angle is reset each time power is turned
o.)
HOLD Locks keypad on remote control.
LAMP Turns the LAMP on the interior unit on or o.
AIR FLOW Changes the directional airow.
SLEEP Press to enter SLEEP mode. SLEEP mode automatically adjusts
the set point by 2 degrees after the rst hour of operation to
provide greater comfort overnight as well as to save energy.
CLEAN Press this before cleaning evaporator coils with warm water.

NOTES
11 12
NOTES