CLIVET DUCT-SL 2 Series User manual

TECHNICAL MANUAL
DUCT-SL 2 35M-160M
OUTDOOR UNIT-SL 2 35M-160T
NOTE: FOR SIZE 53M, SEE DEDICATED TECHNICAL MANUAL
LIGHT COMMERCIAL R32
07/02/2019
TM19B005GB-00

Table of Contents Page
1. Specifications ................................................................................................ 4
1. Model Reference
2. General Specifications
3. Dimensional Drawings
4. Centre of Gravity
5. Electrical Wiring Diagrams
6 Refrigerant Cycle Diagrams
7. Capacity Tables
8. Capacity Correction Factor for Height Difference
9. Noise Data
10. Electrical Characteristics
11. Static Pressure
2. Product Features ........................................................................................... 76
1. Operation Modes and Functions
2. Remote Controller Functions
3. Installation .................................................................................................... 87
1. Installation Overview
2. Location Selection
3. Indoor Unit Installation
4. Outdoor Unit Installation
5. Drainage Pipe Installation
6. Refrigerant Pipe Installation
7. Vacuum Drying and Leakage checking
8. Additional Refrigerant Charge
9. Engineering of Insulation
10. Engineering of Electrical Wiring
11. Test Operation

Table of Contents Page
4. Static Pressure Design .................................................................................. 103
1. Introduction
2. Charts for friction losses in round ducts
3. Dynamic losses
4. Corresponding relation between Rectangular duct and Round duct
5. Method for duct calculation
6. Unit conversion
7. Recommended outlet velocity for different occasions

Contents
1. Model Reference....................................................................................................5
2. General Specifications...........................................................................................6
3. Dimensional Drawings ........................................................................................10
4. Centre of Gravity .................................................................................................13
5. Electrical Wiring Diagrams..................................................................................16
6 Refrigerant Cycle Diagrams ................................................................................30
7. Capacity Tables ....................................................................................................34
8. Capacity Correction Factor for Height Difference .............................................58
9. Noise Data............................................................................................................64
10. Electrical Characteristics......................................................................................70
11. Static Pressure......................................................................................................71
Specifications

Specifications
Page 5 
1. Model Reference
Refer to the following table to determine the specific indoor and outdoor unit model number of your purchased
equipment.
Indoor Unit Model Outdoor Unit Model Capacity (Btu/h) Power Supply
ID2-XY 35M MC2-Y 35M 12K
1Φ, 220-240V~, 50HzID2-XY 70M MC2-Y 70M 24K
ID2-XY 105M MC2-Y 105M 36K
ID2-XY 105M MC2-Y 105T 36K
3Φ, 380-410V~, 50HzID2-XY 140M MC2-Y 140T 48K
ID2-XY 160M MC2-Y 160T 55K

Specifications
Page 6 
2. General Specifications
Indoor model ID2-XY 35M ID2-XY 70M ID2-XY 105M
Outdoor model MC2-Y 35M MC2-Y 70M MC2-Y 105M
Power supply (Indoor ) V- Ph-Hz 220~240-1-50 220~240-1-50 220~240-1-50
Power Supply (Outdoor)V-Ph-Hz 220~240-1-50 220~240-1-50 220~240-1-50
Max. input consumption W 2350 2950 4700
Max. current A 10.0 13.5 21.5
Indoor fan motor
Model ZKFN-55-8-22 ZKFN-160-8-1-2 ZKFN-300-8-1
Qty 111
Insulation class EEE
IP rating IPX0 IPX0 IPX0
Input W 130.0 90.0 250.0
Capacitor uF - / /
Speed(Hi/Mi/Lo) r/min 1170/1030/850 920/850/770 1100/1000/900
Indoor coil
Number of rows 3.0 3.0 4.0
Tube pitch(a)x row pitch(b) mm 21x13.37 21x13.37 21x13.37
Fin spacing mm 1.4 1.4 1.4
Fin type (code) Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum
Tube outside dia.and type mm Φ7,Inner groove tube Φ7,Inner groove tube Φ7,Inner groove tube
Coil length x height x width mm 526x210x40.11 915x294x40.11 1175x294x53.48
Number of circuits 477
Indoor air flow (Hi/Mi/Lo) m3/h 600/480/300 1248/1054/839 1400/1150/750
ESP
Rated Pa 25 25 37
Range Pa 0-60 0-160 0-160
Indoor sound pressure level dB(A) 35/30.5/26 41.5/39.5/37.5 44.5/41.5/38.5
Indoor sound power level dB(A) 56 62 63
Indoor unit
Dimension(W*D*H) mm 700x450x200 1100x774x249 1360x774x249
Packing (W*D*H) mm 860x540x285 1305x805x305 1570x805x305
Net/Gross weight Kg 18/22 31.5/38.9 40.5/48.5
Design pressure MPa 4.3/1.7 4.2/1.5 4.2/1.5
Drainage water pipe diameter mm ODΦ25mm ODΦ25mm ODΦ25mm
Refrigerant piping Liquid side/ Gas side mm(inch) Φ6.35/Φ9.52(1/4"/3/8") Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8")
Controller Wired control Wired control Wired control
Operation temperature °C 17-30 17-30 17-30
Room temperature
Cooling °C 17~32 17~32 17~32
Heating °C 0~30 0~30 0~30
Qty’per 20’ /40’ /40’HQ Indoor unit 214/461/519 77/161/184 49/105/120
Compressor
Model KTN110D42UFZ KTF235D22UMT KTF310D43UMT
Type ROTARY ROTARY ROTARY
Brand GMCC GMCC GMCC
Capacity W 3465 7650 10010
Input W 885 2065 2765
Rated current(RLA) A 5.95 9.4 5.38
Refrigerant oil/oil charge ml VG74/350 RB74A F/670 VG74/1000
Outdoor fan motor
Model ZKFN-40-8-1L-5 ZKFN-50-8-2 ZKFN-120-8-2
Qty 111
Insulation class EEE
IP rating IPX4 IPX0 IPX4
Output W 40.0 115.0 150.0
Capacitor uF ///
Speed r/min 850 850 1050

Specifications
Page 7 
Outdoor coil
Number of rows 2.0 2.0 2.0
Tube pitch(a)x row pitch(b) mm 21x22 25.4x22 25.4x22
Fin spacing mm 1.2 1.4 1.3
Fin type (code) Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum
Tube outside dia.and type mm Φ7,Inner groove tube Φ9.52,Inner groove tube Φ9.52,Inner groove tube
Coil length x height x width mm 860x504x44 730x660x44 995x762x44
Number of circuits 444
Outdoor air flow m3/h 2000 2700 4000
Outdoor sound pressure level dB(A) 55.5 60.5 62.5
Outdoor sound power level dB(A) 61 65 67
Throttle type EXV EXV+Capillary EXV+Capillary
Outdoor unit
Dimension(W*D*H) mm 800x333x554 845x363x702 946x410x810
Packing (W*D*H) mm 920x390x625 965x395x765 1090x500x875
Net/Gross weight Kg 34.7/37.5 49.4/52.8 66.8/73.4
Refrigerant type
Type - R32 R32 R32
GWP - 675 675 675
Charged quantity Kg 0.87 1.5 2.4
Design pressure MPa 4.3/1.7 4.3/1.7 4.3/1.7
Refrigerant piping
Liquid side/ Gas side mm(inch) Φ6.35/Φ9.52(1/4"/3/8") Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8")
Max. refrigerant pipe length m 25 50 65
Max. difference in level m 10 25 30
Ambient temperature
Cooling °C -15~50 -15~50 -15~50
Heating °C -15~24 -15~24 -15~24
Qty’per 20’ /40’ /40’HQ Outdoor unit 108/219/292 102/215/216 44/96/144
Notes:
1) Capacities are based on the following conditions:
Cooling(T1): - Indoor Temperature 27°C(80.6°F) DB /19 °C(66.2°F) WB Heating: - Indoor Temperature 20°C(68°F) DB / 15°C(59°F) WB
-Outdoor Temperature 35 °C(95°F) DB /24 °C(75.2°F) WB -Outdoor Temperature 7°C(44.6°F) DB / 6°C(42.8°F) WB
-Interconnecting Piping Length 5m - Interconnecting Piping Length 5 m
- Level Difference of Zero. - Level Difference of Zero.
2) Capacities are Net Capacities.
3) Due to our policy of innovation some specifications may be changed without notification.

Specifications
Page 8 
Indoor model ID2-XY 105M ID2-XY 140M ID2-XY 160M
Outdoor model MC2-Y 105T MC2-Y 140T MC2-Y 160T
Power supply (Indoor ) V- Ph-Hz 220~240-1-50 220~240-1-50 220~240-1-50
Power Supply (Outdoor)V-Ph-Hz 380~415-3-50 380~415-3-50 380~415-3-50
Max. input consumption W 5600 6200 7500
Max. current A 10.0 11.2 14
Indoor fan motor
Model ZKFN-300-8-1 ZKFN-560-8-1-1 ZKFN-560-8-1-1
Qty 1 1 1
Insulation class E E E
IP rating IPX0 IPX0 IPX0
Input W 250.0 560.0 560.0
Capacitor uF / / /
Speed(Hi/Mi/Lo) r/min 1100/1000/900 1020/800/600 1060/970/905
Indoor coil
Number of rows 4.0 4.0 4.0
Tube pitch(a)x row pitch(b) mm 21x13.37 21x13.37 21x13.37
Fin spacing mm 1.4 1.5 1.5
Fin type (code) Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum
Tube outside dia.and type mm Φ7,Inner groove tube Φ7,Inner groove tube Φ7,Inner groove tube
Coil length x height x width mm 1175x294x53.48 1030x378x53.48 1030x378x53.48
Number of circuits 7 8 8
Indoor air flow (Hi/Mi/Lo) m3/h 1400/1150/750 2400/2040/1680 2600/2210/1820
ESP
Rated Pa 37 50 50
Range Pa 0-160 0-160 0-160
Indoor sound pressure level dB(A) 50/43/40 50.5/49.5/48 54/52/50.5
Indoor sound power level dB(A) 63 67 71
Indoor unit
Dimension(W*D*H) mm 1360x774x249 1200x874x300 1200x874x300
Packing (W*D*H) mm 1570x805x305 1405x915x355 1405x915x355
Net/Gross weight Kg 40.5/48.5 47.6/55.8 47.6/55.8
Design pressure MPa 4.2/1.5 4.2/1.5 4.2/1.5
Drainage water pipe diameter mm ODΦ25mm ODΦ25mm ODΦ25mm
Refrigerant piping Liquid side/ Gas side mm(inch) Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8")
Controller Wired control Wired control Wired control
Operation temperature °C 17-30 17-30 17-30
Room temperature
Cooling °C 17~32 17~32 17~32
Heating °C 0~30 0~30 0~30
Qty’per 20’ /40’ /40’HQ Indoor unit 49/105/120 62/130/149 62/130/149
Compressor
Model KTF310D43UMT KTQ420D1UMU KTQ420D1UMU
Type ROTARY ROTARY ROTARY
Brand GMCC GMCC GMCC
Capacity W 10010 13700 13700
Input W 2765 3700 3700
Rated current(RLA) A 5.38 7.02 7.02
Refrigerant oil/oil charge ml VG74/1000 VG74/1400 VG74/1400
Outdoor fan motor
Model ZKFN-120-8-2 ZKFN-85-8-22 ZKFN-85-8-22-2
Qty 1 2 2
Insulation class E E E
IP rating IPX4 IPX4 IPX4
Output W 150.0 126.0 126.0
Capacitor uF / / /
Speed r/min 1050 850 850

Specifications
Page 9 
Outdoor coil
Number of rows 2.0 1.6 2.0
Tube pitch(a)x row pitch(b) mm 25.4x22 25.4x22 25.4x22
Fin spacing mm 1.3 1.4 1.4
Fin type (code) Hydrophilic aluminum Hydrophilic aluminum Hydrophilic aluminum
Tube outside dia.and type mm Φ9.52,Inner groove tube Φ9.52,Inner groove tube Φ9.52,Inner groove tube
Coil length x height x width mm 995x762x44 990x1270x22+500x1270x22 990x1270x44
Number of circuits 4 8 8
Outdoor air flow m3/h 4000 7500 7500
Outdoor sound pressure level dB(A) 64 66 63.5
Outdoor sound power level dB(A) 67 72 73
Throttle type EXV+Capillary EXV+Capillary EXV+Capillary
Outdoor unit
Dimension(W*D*H) mm 946x410x810 952x415x1333 952x415x1333
Packing (W*D*H) mm 1090x500x875 1095x495x1480 1095x495x1480
Net/Gross weight Kg 81.5/87.0 106.7/119.9 111.3/124.3
Refrigerant type
Type - R32 R32 R32
GWP - 675 675 675
Charged quantity Kg 2.4 2.8 2.95
Design pressure MPa 4.3/1.7 4.3/1.7 4.3/1.7
Refrigerant piping
Liquid side/ Gas side mm(inch) Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8") Φ9.52/Φ15.9(3/8"/5/8")
Max. refrigerant pipe length m 65 65 65
Max. difference in level m 30 30 30
Ambient temperature
Cooling °C -15~50 -15~50 -15~50
Heating °C -15~24 -15~24 -15~24
Qty’per 20’ /40’ /40’HQ Outdoor unit 44/96/144 22/48/48 22/48/48
Notes:
1) Capacities are based on the following conditions:
Cooling(T1): - Indoor Temperature 27°C(80.6°F) DB /19 °C(66.2°F) WB Heating: - Indoor Temperature 20°C(68°F) DB / 15°C(59°F) WB
-Outdoor Temperature 35 °C(95°F) DB /24 °C(75.2°F) WB -Outdoor Temperature 7°C(44.6°F) DB / 6°C(42.8°F) WB
-Interconnecting Piping Length 5m - Interconnecting Piping Length 5 m
- Level Difference of Zero. - Level Difference of Zero.
2) Capacities are Net Capacities.
3) Due to our policy of innovation some specifications may be changed without notification.

Specifications
Page 10 
3. Dimensional Drawings
3.1 Indoor Unit
Model unit A B C D E F G H I J K L M H1 H2 W1 W2
ID2-XY
35M
mm 700 200 506 450 137 537 30 1152 599 186 50 741 360 84 140 84 84
inch 27.6 7.9 19.9 17.7 5.4 21.1 1.2 6.0 23.6 7.3 2.0 29.2 14.2 3.3 5.5 3.3 3.3
ID2-XY
70M
mm 1100 249 774 700 140 926 50 175 1001 228 5 1140 598 80 150 130 155
inch 43.31 9.80 30.47 27.56 5.51 36.46 1.97 6.89 39.41 8.98 0.2 44.88 23.54 3.15 5.91 5.12 6.10
ID2-XY
105M
mm 1360 249 774 700 140 1186 50 175 1261 228 5 1400 598 80 150 130 155
inch 53.54 9.80 30.47 27.56 5.51 46.69 1.97 6.89 49.65 8.98 0.2 55.12 23.54 3.15 5.91 5.12 6.10
ID2-XY
140M-
160M
mm 1200 300 874 800 123 1044 50 227 1101 280 5 1240 697 80 150 185 210
inch 47.24 11.81 34.41 31.5 4.84 41.1 1.97 8.94 43.35 11.02 0.2 48.82 27.44 3.15 5.91 7.28 8.27

Specifications
Page 11 
3.2 Outdoor Unit
Single Fan Outdoor Unit
Model unit W D H W1 A B
MC2-Y 35M mm 800 333 554 870 514 340
inch 31.49 13.11 21.81 34.25 20.23 13.39
MC2-Y 70M mm 845 363 702 914 540 350
inch 33.27 14.29 27.64 35.98 21.26 13.78
MC2-Y 105M mm 946 410 810 1030 673 403
inch 37.24 16.14 31.89 40.55 26.50 15.87
MC2-Y 105T mm 946 410 810 1030 673 403
inch 37.24 16.14 31.89 40.55 26.50 15.87

Specifications
Page 12 
Double Fan Outdoor Unit
Model unit W D H W1 A B
MC2-Y 140T mm 952 415 1333 1045 634 404
inch 37.48 16.34 52.48 41.14 24.96 15.9
MC2-Y 160T mm 952 415 1333 1045 634 404
inch 37.48 16.34 52.48 41.14 24.96 15.9

Specifications
Page 13 
4. Centre of gravity
MC2-Y 35M,
MC2-Y 70M

Specifications
Page 14 
MC2-Y 105M, MC2-Y 105T

Specifications
Page 15 
MC2-Y 140T, MC2-Y 160T

Specifications
Page 16 
5. Electrical Wiring Diagrams
5.1 Indoor unit
Abbreviation Paraphrase
Y/G Yellow-Green Conductor
CAP1 Indoor Fan Capacitor
FAN Indoor Fan
PUMP PUMP
L LIVE
N NEUTRAL
TO CCM Comm.Bus Central Controller
T1 Indoor Room Temperature
T2 Coil Temperature of Indoor Heat Exchanger
P1 Super High Speed
P2 High Speed

Specifications
Page 17 
ID2-XY 70M, ID2-XY 105M, ID2-XY 105M, ID2-XY 140M, ID2-XY 160M

Specifications
Page 18 
ID2-XY 35M
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
12
ON
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
12
ON
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
12
ON
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
12
ON
S1+S2
0~F0~F0~F0~F
NETADDRESS
CODE
0~15 16~31 32~47 48~63
FACTORY SETTING
FOR SETTING NETADDRESS
INDOOR UNIT
MAINBOARD
CN33
ALARM
Alarm
Output
12
ON
12
ON
12
ON
12
ON
EEPROM
DEFAULT
FACTORY
SETTING
FOR TEMP. COMPENSATION(HEATING)
SW6
CODE
6℃2℃4℃
T2
T1
CN6 4INDOOR COIL TEMP. SENSOR
ROOM TEMP. SENSOR
CN5
WATER LEVEL SWITCH
CN9
XYE
To CCM
Comm.Bus
Y/G
CN18
J7
CN23
ON/OFF
Remote
Control
CN43
FAN FOR THE
FRESH AIR
OR ANION
GENERATOR
NOTE:
1.The parts with dotted line indicates
optional features.
2.Remove the short connector of J7
when you use the "on-off" function.
AC FAN
CAP
Y/G
WHITE WHITE
(GRAY)
CN4
P1
P2
BLACK
BROWN
M
53
FOR SETTING FAN MOTOR CONTROL
WHEN THERE IS NO DEMAND
1
ON
1
ON
SW2
FAN OFF FAN ON
MODE
FACTORY SETTING
12
ON
12
ON
12
ON
12
ON
SW1
TEL0 24
℃
15 ℃
8 ℃
EEPROM
DEFAULT
FACTORY
SETTING
FOR ANTI-COLD WIND
RED
CN2
CN1
BLACK
CN3 YELLOW
TO OUTDOOR UNIT
1(L)
2(N)S
1
ON
1
ON
FACTORYSETTING
FOR SETTINGAUTO-RESTART
FOR SETTINGAUTO-RESTART
SW3
MODEAUTO-RESTARTNOTAUTO-RESTART
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
0
8
4
1
2
3
5
6
7
C
9
A
B
D
E
F
ENC1
012
POWER
CODE
20
26 32~35
FACTORY
SETTING
ACCORDING TO RELATED MODEL.
FOR SETTING POWER
CN13 MPUMP
2
REACTOR
CON2
RED
RED
DC MOTOR
DRIVER MODLE
CON1
FAN1
3
3
4
CN1
CN15
CN34
DC FAN
M
3
CN40
WIRE
CONTROLLE
R
4
MAGNETIC RING
HB HA
CN45
WIRE
CONTROLLE
R
MAGNETIC RING
DISPLAY
BOARD
WIRE
CONTROLLER
10
CN105
MAGNETIC RING
Y/G
16023000008781 WIRING DIAGRAM
W
RED
NOTE:
Please don't connect "W" if there
is no terminal in outdoor unit."W"
INDOOR UNIT
1(L)2(N)S
123
W
INDOOR UNIT
1(L)2(N)S
123
W
Air Condition Link-Circuit
OUTDOOR UNIT
Power supply:3-Phase 380-415V~
5-core cable 5x2.5mm
Power supply:3-Phase 220V~
5-core cable 5x4.0mm
2
2
1(L) 2(N)
S
L1 L2 L3 N
OUTDOOR UNIT
Power supply:
24K : 3-core cable 3x2.5mm
25K-36K : 3-core cable 3x4.0mm
37K : 3-core cable 3x6.0mm
1-Phase 208-240V~
≤
≥
2
2
2
1(L) 2(N) S
If there is no Wterminal in outdoor unit:
4-core cable 4x2.5mm
(with auxiliary electric heater)
If there is aW terminal in outdoor unit:
“”
“”
4-core cable 4x1.0mm
5-core cable 5x1.0mm
5-core cable 5x2.5mm
(with auxiliary electric heater)
123
L(L1) N(L2)
123
16022700002888
- - - - This symbol indicates the
element is optional,the actual
shape shall prevail.This wiring
diagram is just for mono;Don't
connect to W if there is no W
terminal in outdoor unit.
W
W
2
2
2
2
If there is no Wterminal in outdoor unit:
4-core cable 4x2.5mm
(with auxiliary electric heater)
If there is aW terminal in outdoor unit:
“”
“”
4-core cable 4x1.0mm
5-core cable 5x1.0mm
5-core cable 5x2.5mm
(with auxiliary electric heater)
2
2
2
2

Specifications
Page 19 
5.2 Some connectors introduce:
A. For new fresh motor terminal port (also for Anion generator) CN43:
1. Connect the fan motor to the port , no need care L/N of the motor ;
2. The output voltage is the power supply;
3. The fresh motor can not excess 200W or 1A , follow the smaller one ;
4. The new fresh motor will be worked when the indoor fan motor work ;when the indoor fan
motor stops , the new fresh motor would be stopped ;
5. When the unit enter force cooling mode or capacity testing mode , the fresh motor isn’t work .

Specifications
Page 20 
B For ALARM terminal port CN33
1. Provide the terminal port to connect ALARM ,but no voltage of the terminal port , the power from
the ALARM system (not from the unit )
2. Although design voltage can support higher voltage ,but we strongly ask you connect the power
less than 24V, current less than 0.5A
3. When the unit occurs the problem , the relay would be closed , then ALARM works