CNB XNET User manual

XNET Network Video Server User’s Guide
1 of 44
XNET Network Video Server
User’s Guide
Ver. 1.0 (071024)

XNET Network Video Server User’s Guide
2 of 44
Directions
XNET are designed for indoor use only. When using XNET outdoors or in an environment that
exceeds the limited range, you must separately use a water-resistant case.
Be careful not to cause any physical damage by dropping or throwing the XNET. Especially keep
the device out of reach from children.
Do not disassemble XNET. You will be excluded from After Service when disassembled.
Use only the power adapter provided with the XNET.
If you would like to use the XNET for security, monitoring, please check the legal regulations
within the country.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Caution
Any changes or modifications in construction of this device which are not explicitly approved
by the party responsible for compliance could void the user‟s authority to operate the
equipment.

XNET Network Video Server User’s Guide
3 of 44
1. Introduction.................................................................................................................. 4
1.1. Overview............................................................................................................ 4
1.2. Features of XNET ............................................................................................... 4
1.3. Applications of XNET .......................................................................................... 4
2. Product Description........................................................................................................ 5
2.1. Contents ............................................................................................................ 5
2.2. Preview.............................................................................................................. 5
2.3. Physical description............................................................................................ 6
2.4. PC Requirements.............................................................................................. 10
2.5 Quick Installation Guide .................................................................................... 10
3. Connecting XNET to Network ........................................................................................ 13
3.1. Connecting to LAN ........................................................................................... 13
3.2. Connecting to xDSL/Cable Modem ................................................................... 14
4. IP-Installer ................................................................................................................. 15
4.1. Main window of IP-Installer.............................................................................. 15
5. Configuring XNET in Administrative Mode ....................................................................... 16
5.1. Log On ............................................................................................................. 16
5.2. Basic Setup...................................................................................................... 18
5.3. Network Configuration ..................................................................................... 20
5.4. User Admin & Time Setup ................................................................................ 23
5.5. Sensor & Capture Setup................................................................................... 26
5.6. Alarm Device Setup ......................................................................................... 28
5.7. Motion Region Setup ........................................................................................ 29
5.8. PTZ Setup ........................................................................................................ 31
5.9. Encryption Set up ............................................................................................ 33
5.10. Upgrade & Reset ............................................................................................ 35
5.11. Status Report................................................................................................. 37
6. Tips for using XNET ..................................................................................................... 38
6.1. ALARM-IN and ALARM-OUT .............................................................................. 38
6.2. Trouble Shooting .............................................................................................. 41
6.3. Web Viewer...................................................................................................... 42
6.4. How to Upgrade the XNET................................................................................ 44
Table of Contents

XNET Network Video Server User’s Guide
4 of 44
1. Introduction
1.1. Overview
The XNET is a state-of-the-art network camera which transmits synchronized video and audio
data in real time with D1 resolution at full frame rate. This is possible through MPEG4 CODEC
technology, which provides high quality video with highly compressed data streams. The XNET
can be connected, controlled and monitored from a remote location through an IP connection
over internet or intranet. Unlike CCTV or DVR, the XNET is easy to install and owner will
experience cost and space savings in the installation owing to the state of the art technologies
embedded in the system. Based on Embedded Software Solution (Embedded Web Server,
Embedded Streaming Server, Network Protocol), the XNET ensures unprecedented performance
and stability to be an ideal network camera solution for system integration solutions.
1.2. Features of XNET
1 channel synchronized real time Video/Audio streaming
MPEG-4 video, ADPCM audio.
Bi-directional audio communication
Real time audio communication between XNET and Client PC
The viewer assisted recording and playback functions.
1 Alarm sensor input/1 relay output
Motion detection –Up to 3 motion detection zones
Arbitrary shape motion detection zone
Motion detection can initiate video recording, which is sent to the user through FTP and/or E-
mail.
Resolution
- NTSC : 720x480, 352x240, 176x144.
- PAL/SECAM : 720x576, 352x288, 176x144
RS-485 interface for Pan/Tilt device connection
Remote administration control
Entire operational parameter set up, Software upgrade
Proprietary PoE (Power over Ethernet) for convenience of installation and cost savings
1.3. Applications of XNET
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks,
government facilities, military, etc.)
Real time Internet broadcasting

XNET Network Video Server User’s Guide
5 of 44
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference)
Remote Learning
Weather and environmental observation
2. Product Description
2.1. Contents
Open the package and check if you have the followings:
Components
Description
Remarks
XNET
XNET Network Camera
Power adaptor
Input : 100~250V 50-60Hz
Output : +12V, 3.3A
Standard Power
AC power cable
AC 250V, 10A~16A
CD
Software & User‟s Guide
Quick Reference Guide
Quick installation guide
2.2. Preview
XNET/XNET
IP-Installer
XNET-NVR
INS1000
IJB1000
MPEG-4 Network Video
Server
PC software to allocate an IP
address to the XNET
PC software to view and record
the A/V streaming data
transmitted from the XNET.
There are two editions available
(NVR/XNVR)

XNET Network Video Server User’s Guide
6 of 44
2.3. Physical description
2.3.1. INS1000
Figure 2-1 Front view of INS1000
Figure 2-2. Rear view of INS1000
VIDEO IN : Connect external video source(NTSC/PAL).
VIDEO OUT : Composite video output.
RS-232C
Factory Reset

XNET Network Video Server User’s Guide
7 of 44
MIC /LINE IN : Connect external audio source or microphone. If external audio is
connected, embedded microphone will be disabled.
Use Standard stereo earphone jack for the connection
Audio In
Ground
Not used
Audio In
Ground
Not used
Audio out
Ground
Not used
Audio out
Ground
Not used
Figure 2-3. Pin assignment of the plug for MIC/LINE In (left) and
LINE OUT (right)
LINE OUT : Connect speakers with built in amplifier. Audio from remote site is output
through Line out in bi-directional audio mode.
Use Standard stereo earphone jack for the connection.
NETWORK : 10/100Mbps Ethernet connector (RJ-45) with proprietary PoE.
- LINK/ACT LED : Continuous yellow light means that network cable is plugged in. It will
blink when there is traffic.
- Status LED: Green LED on indicates that the camera is in normal operation mode, while
LED off indicates that the camera is in abnormal condition.
RS-232C
1 2 3
Pin
Description
Misc.
3
TxD of RS-232C
For debugging & factory
use only.
2
RxD of RS-232C
1
Ground of RS-232C
DC Power : Power input of XNET.
Do not apply power through this power input when power is applied through LAN cable
using proprietary PoE.

XNET Network Video Server User’s Guide
8 of 44
RS-485 and ALARM IN/OUT : Used for connecting P/T device, sensor, and alarm devices
to XNET. Pin assignments are as follows
Pin
Description
Misc.
1
Alarm Out
Relay output : closed circuit in
alarm to indicate alarm status.
2
Alarm Out
3
Alarm In (+)
NC/NO selectable in admin mode.
4
Alarm In (-)
5
RS485 +
6
RS485 +
RS-485 : Used for connecting Pan/Tilt and Zoom devices having RS-485
interface standard.
Alarm In : Connect external alarm sensors such as the infrared sensors, heat
sensor, magnetic sensors, etc. NC/NO selectable in the admin page.
Alarm Out : It is used for connecting external alarm generators such as sirens,
flashing light, etc. When activated, relay output configures a closed circuit.
Please refer to Section 6.1 for more detailed description on the Alarm In/Out
connections.
Reset : Factory Default Switch
There is a switch provided for returning the network camera to factory default state. Press
the switch about 3 seconds through a tiny hole at the left of the 100BaseT connector using
tools with sharp tip for a few seconds while power is applied.
1 6

XNET Network Video Server User’s Guide
9 of 44
2.3.2. IJB1000
Figure 2-4. IJB1000 (Each function of wire is same as IVS100.)

XNET Network Video Server User’s Guide
10 of 44
2.4. PC Requirements
AV streaming data received from XNET can be decoded or stored in a PC running XNET-NVR
program which is a viewing & recording program for a PC. Minimum requirement of the PC is
described below:
Minimum
Recommended
CPU
Pentium III 700
Pentium IV 1.2G above
Main Memory
128 MB
256MB above
Operating system*
Windows 2,000 or later
Windows 2,000 or later
Web browser
Internet Explorer 5.0
Internet Explorer 5.0 above
Resolution
1,024 X 768
Higher than 1,024 X 768
Network
10 Base-T Ethernet
100 Base-T Ethernet
* Operating Systems supported : Windows 2000 Professional
Windows XP Professional / Windows XP Home Edition
2.5 Quick Installation Guide
Brief information for rapid installation is provided in this section. For more detailed information
you are recommended to refer to pertinent documentations provided with the product or refer
to cnbtec‟s home page (http://www.cnbtec.com)
1. Connect XNET to LAN by using one of the following method
1) If you have power adaptor with PoE, connect the network camera and PC as
illustrated in Figure 2.5. Both power and network connection is made with a single LAN
cable.
The propriety PoE (Power over Ethernet) adds convenience in installing the network
camera by providing both power and LAN connection using single LAN cabling.
2) If you have standard power connect the network camera and PC as illustrated in
Figure 2.6.
Figure 2-5. Connecting Network camera and PC using PoE Adaptor
XNET
PoE
Injector
AC In
LAN Hub
Data + Power
CAT5 cable