Colebrook Bosson Saunders Lima User manual

INSTALL VESA PLATE
IMPORTANT
It is the responsibility of the installer to ensure all mounting
screws are properly inserted into the mount. Under or over insertion
may cause damage to the equipment or injury to personnel.
INSTALL LAPTOP MOUNT TO ARM
INSTALL LAPTOP CABLES INTO
CABLE MANAGEMENT FEATURES
TO REMOVE LAPTOP FROM MOUNT
USING YOUR LAPTOP MOUNT TO REMOVE LAPTOP MOUNT FROM ARM
1
2
4
5
6
7
Once it has been correctly
set up, you will be able to
easily position your laptop
wherever you want it.
Ensure that portrait/
landscape action is returned
to vertical position.
click!
MOUNT LAPTOP 3
IMPORTANT
Ensure you leave enough free cable to avoid stretching or
snagging at all positions of arm movement and laptop tilt.
TIP
Please refer to instructions supplied with monitor arm on how to adjust
height of arm.
NOTE
The Laptop Mount also supports dual screen working.
WARNING
Stored energy hazard when using a dynamic monitor arm.
Arm mechanism is under tension and will spring up when load is
removed. Failure to follow instructions could result in injury.
WARNING
If using a dynamic monitor arm, raise arm to uppermost position before
removing Laptop Mount, otherwise it may spring up when unloaded.
Ensure the laptop is not on tray when removing.
IMPORTANT
Ensure Laptop Mount does not go beyond vertical.
3B
If mounting a laptop to a
dynamic monitor arm, the
spring tension may need to be
adjusted to suit the mounted
weight. Please refer to the
instructions supplied with your
chosen arm.
3A
3C
PUSH
FOLD FOLD FOLD
IMPORTANT
Pull out the retainers. Push the
laptop down
into position
on the Laptop
Mount.
IMPORTANT
Ensure the quick release mechanism
on the VESA is held down throughout
removing the Laptop Mount.
Push down the retainers
to secure laptop.
DO NOT exceed maximum recommended load.
TOTAL MAX
2.8KG/6.2LB
WARNING
Ensure the shorter screws (M4 x 10) provided with the VESA plate are used.

LIMA LAPTOP MOUNT
INSTALLATION INSTRUCTIONS
www.colebrookbossonsaunders.com
LAP/004
COMPONENT LIST
TOTALMAX
2.8KG/6.2LB
Lima Laptop Mount x 1
FOLD FOLD
Please consider leaving these instructions with the
product if further installation may be required by others
Colebrook Bosson Saunders hold a number of patents and other intellectual property rights covering our
products and processes. You can find patent information on our website at:
www.colebrookbossonsaunders.com/patents
PATENTS
LAP-004-INST-C-SEP 2020
2.8
6.2
2.8
As part of Colebrook Bosson Saunders ongoing product improvement programme, the design
of products may change without prior notice and details may vary from those illustrated.
DISCLAIMER
WARNING
• Ensure desk/work surface/wall/partition is suitable to take the weight of the
products and devices.
• Do not use this product for any purpose other than that for which it was designed.
• Supported weight must not exceed 2.8kg (6.2lb).
• Hold the device tightly when making adjustments.
• Care should be taken to avoid trapping fingers.
• Do not dismantle or remodel this product.
• Do not mount the device before assembling the product.
MAINTENANCE AND INSPECTION
• Ensure all screws are tightened and occasionally adjust if needed.
• Clean with a damp cloth, NO solvent.
DISCLAIMER
WARNUNG
• Sicherstellen, dass Schreibtisch/Arbeitsfläche/Wand/Trennwand das Gewicht von
dem Produkt und dem montierten elektronischen Gerät tragen kann.
• Dieses Produkt nur für den Zweck verwenden, für den es konstruiert wurde.
• Maximale Belastung darf 2,8kg (6,2lb) nicht überschreiten.
• Das elektronische Gerät beim Einstellen gut festhalten.
• Vorsicht: Nicht die Finger einklemmen.
• Das Produkt nicht auseinander nehmen oder umbauen.
• Das elektronische Gerät erst dann montieren, wenn das Produkt installiert ist.
WARTUNG UND INSPEKTION
• Sicherstellen, dass alle Schrauben festgezogen sind und, falls erforderlich,
gelegentlich nachstellen.
•Mit einem feuchten Tuch säubern, KEINE Lösemittel.
AVERTISSEMENT ET MISE EN GARDE
• Assurez-vous que le bureau / la surface de travail / le mur / la cloison sont adaptés
pour supporter le poids des produits et des appareils.
• Ce produit ne doit pas servir à d’autres fins que celle prévue.
• Le poids pris en charge ne doit pas dépasser 2,8 kg (6,2 lb).
• Tenez fermement l’appareil lorsque vous effectuez des réglages.
• Faire attention à ne pas se coincer les doigts.
• Ne démontez pas et ne remodelez pas ce produit.
•Ne montez pas l’appareil avant d’assembler le produit.
ENTRETIEN ET INSPECTION
• S’assurer que toutes les vis sont bien serrées et les resserrer au besoin.
• Nettoyer à l’aide d’un chiffon humide. PAS DE solvants.
ADVERTENCIA
• Asegurarse de que el escritorio/la superficie de trabajo/la pared/el tabique sea
adecuado para soportar el peso de los productos y el dispositivo electrónico.
• No usar este producto para otro propósito que no sea aquel para el cual fue
diseñado.
• El peso soportado no debe exceder 2,8kg (6,2lb).
• Sujetar el dispositivo firmemente cuando se realicen ajustes.
• Tomar precauciones para evitar pillarse los dedos.
• No desarmar o remodelar el producto.
• No instalar el dispositivo electrónico antes de instalar el producto.
MANTENIMIENTO E INSPECCIÓN
• Asegurarse de que todos los tornillos estén apretados y ajustarlos de nuevo si fuera
necesario.
• Limpiar con un paño húmedo, no utilizar solventes.