ColorKey Mover MicroSpot User manual

Mover MicroSpot
CKU01-5000 (US) / CKE01-5000 (EU)
USER MANUAL

1
Introduction
Thank you for purchasing the ColorKey Mover MicroSpot. Please read these instructions
carefully before use. O perating this fixture according to these instructions is important to
avoid any possible damage or accidents caused by misuse.
!Packing list
"1x Mover MicroSpot moving head fixture
"1x Power cord
"User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
!This fixture is for indoor use only.
!This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
!Do not install or operate this fixture near flammable materials.
!This device must be installed, operated, and maintained by a qualified professional.
!Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
!Please check if the voltage is in accordance with the rated power before installing.
!Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

2
Display Operation
!MENU: Access the menu/Scroll through menu options
!ENTER: Open/Select the current menu option
!UP: Scroll through menu selection or parameter increase
!DOWN: Scroll through menu selection or parameters decrease

3
DMX Values
11 channel mode
9 channel mode
Value
Function
1
1
000-255
Pan
Pan (fine)
2
3
2
000-255
Tilt
Tilt (fine)
4
5
3
000-007
008-014
015-021
022-028
029-035
036-042
043-049
050-056
057-127
128-189
190-193
194-255
Color
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Half color
Color wheel speed (fast-slow)
Stop
Color wheel speed (slow-fast)
6
4
000-007
008-015
016-023
024-031
032-039
040-047
048-055
056-063
064-071
072-079
080-087
088-095
096-103
104-111
112-119
120-127
128-189
190-193
194-255
Gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 1 shake
Gobo 2 shake
Gobo 3 shake
Gobo 4 shake
Gobo 5 shake
Gobo 6 shake
Gobo 7 shake
Gobo 8 shake
Gobo wheel speed (fast-slow)
Stop
Gobo wheel speed (slow-fast)
7
5
000-255
Strobe
8
6
000-255
Dimmer
9
7
000-255
Pan/Tilt speed

4
10
8
000-069
070-079
080-089
090-099
100-109
110-119
120-199
200-209
210-249
250-255
Mode
-
Black out when Pan/Tilt rotating
-
Black out when Color wheel rotating
-
Black out when Gobo wheel rotating
-
Reset
-
Sound function
11
9
000-255
Dimming mode
Menu Guide
Main Menu
Sub Menu
Function
Menu
ADDR
0-512
DMX addressing
CHND
8CH/10CH
Channel section
SLMD
MAST
Mast mode
SL1
Slave mode 1
SL2
Slave mode 2
SHND
SH1
Sound operation 1
SH2
Sound operation 2
SH3
Sound operation 3
SH4
Sound operation 4
SOUN
ON
ON (sound function)
OFF
OFF (sound function)
SENS
000-100
Sensor sensitivity (Sound function)
LED
ON
ON (LED display)
OFF
OFF(LED display OFF with no operation to
LED panel in one minute)
DISP-INVERT
LED display (forward/backward)
PAN INVERT
YES
PAN forward rotation
NO
PAN backward rotation
TILT INVERT
YES
Tilt forward rotation
NO
Tilt backward rotation
TEST
Self-Test
Auto running in “self-test” function
VER
Software version
Software version
RESET
Reset
Reset

5
DMX Connections
!DMX Cable：
The Mover MicroSpot can be controlled via DMX using a 3-pin XLR connection. The
standard DMX connection is XLR is: one end connects to the male plug, and the other
connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a
resistance120Ω（1/4W ）at the end of the DMX connecting as below:
!The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

6
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run
longer than 60 meters and/or over 32 units, a signal amplifier may be required.
Troubleshooting
Problem
Solutions
No DMX control
#Make sure that the DMX cable is properly connected
#Make sure that the DMX controller is operational
#Check the DMX cable for tears or breaks
#Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
#Make sure that the fixture is in Sound Active mode.

7
Technical Information
Power supply: AC 110~240V，50/60Hz
Power consumption: 27W
Light Source：1x10W white LED
Life span: 60,000 hours
Beam angle: 13°
Channel: 9/11 DMX channel
Color: 7 colors plus open (white)
Gobo: 7 gobos plus open
Electronic adjustable strobe with high speed
Pan: 540°
Tilt: 270°
Control: Sound activate, master/slave, Automatic, DMX
Standard DMX512 control protocol
Working Environment：up to 40℃; Over heating protection
IP rate：IP20
Notice to consumer: ColorKey offers a 1-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user
manuals and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].