Comfast CF-E5 User manual

M0304346 V1.0

(1) The device defaults to 4G Internet access mode.
(2) Insert the MACRO SIM according to the device mark before
powering up.
(3) Power on the device, connect the wireless SSID of the device
(default is COMFAST_XXXX_2G, XXXX is the last 4 digits of MAC) or
connect the device LAN port to the PC through the network cable.
(4) Open the browser, enter 192.168.10.1 (the mobile terminal can
automatically pop up), set the login password, and enter the page to
check whether the device has read the SIM card.
LAN WAN
RESET
MICRO SIM
USB
LAN
POE
1.1
1.2
4G Internet Mode Setting
LAN
Computer

Normal read status:
Status
Device Info
MAC: 40:A5:EF:12:45:56
Model: CF-E5
Version: V2.6
4G
Carriers: China Mobile
Network: LTE
RSSI: -57dbm
Unread to SIM:
Status
Device Info
MAC: 40:A5:EF:12:45:56
Model: CF-E5
Version: V2.6
4G
No SIM card detected

3.1 : The steps to enter the set interface as follows
(1) Under default configuration, power on the device and wait 90 seconds
untill the device to start.
(2) Connect the device’s LAN port with the computer by a network cable.
(3) . Input 192.168.10.1 in the web browser to enter the set interface
(4)
Password Add
(5) If read normally, you need to modify the wireless SSID and
password. Enter the menu bar on the left, Network Management -
Modify the wireless settings, click on the settings after modifying.
Note:
1. If the SIM card is not read: (1) First check if the SIM card is
inserted in the direction of the mark (2) Check if the SIM card has
a PIN lock. If there is a lock, please unlock the SIM card with the
mobile phone first.
2. Individual operators may prompt Unkown, but the network
access information and signals are normal. This do not affect the
Internet access.
3. Replacing and plugging the SIM card requires restarting the
device.
4. If your card needs to manually set the APN account, please
refer to the manual Router Set 4G mode.
3Other Mode Internet Settings

The AP needs to set an intranet IP address (do not set the same IP
address as the upper router). If want to manage the device, Manually
set the IP address of the same network segment of the intranet IP.
3.3
Router
AP
SWITCH
Internet
Internet
MODEM
WISP AP
Repeater
Bridge
Internet
LAN1 L AN2
Internet
3.2
,Repeater Mode.
four
M
M
LAN

12
Lan Settings WiFi 2.4G Finish
IP Address
Subnet Mask
192.168.10.1
255.255.255.0
3
WiFi 5.8G
Lan Settings
Next
2.4G Wireless
SSID
Password
Prev
COMFAST_E32B_2G
Advanced Setting
20MHz
China
auto
1 2
Lan Settings WiFi 2.4G Finish
3
WiFi 5.8G
Bandwidth
Country
Channel
Next
3.4 AP mode: You can set up 2.4G/5.8G wireless SSID, password,
channel and country in advance. After setting up,the device’s
LAN port connected internet,other mobile devices can connect
the SSID to surf the internet.
3.5 Bridge Mode: Pls ensure the WDS in upper network is enabled.
AP device can set up intranet segment(do not set the same IP
address as the upper router), and then select the wireless SSID
signal you need to bridge(Distinguish between 5.8GHz and 2.4GHz)
and input wireless password.
(Notes: The password is same as your upper network router)
Note: If the device is 2.4G, the 5.8G wireless setting function is
not supported.

2.4G Wireless
Next
SSID
Password
COMFAST_E32B_2G
Prev
12
Lan Settings Bridge Settings
34
WiFi 2.4G Finish WiFi 5.8G
Lan Settings
IP Address
Subnet Mask
Next
192.168.10.1
12
Lan Settings Bridge Settings
34
WiFi 2.4G Finish
255.255.255.0
WiFi 5.8G
Pls set the SSID and password for the device and click “Next” to
finish settings.

3.6 Repeater Mode: The AP device can set the internal network
segment (the gateway IP should not be the same as the upper device
gateway IP). Next, select the name of the wireless SSID signal that
you need to relay (distinguish between 5.8GHz and 2.4GHz).
Lan Settings
IP Address
Subnet Mask
Next
192.168.10.1
12
Lan Settings Repeater Settings
34
WiFi 2.4G Finish
255.255.255.0
WiFi 5.8G
2.4G Wireless
Next
SSID
Password
COMFAST_E32B_2G
Prev
12
Lan Settings Repeater Settings
34
WiFi 2.4G Finish WiFi 5.8G
Pls set the SSID and password for the device and click “Next” to
finish settings.
3.7 four 4G ,
4G Mode: In this mode, you can select automatic APN or manually
set the APN account (the APN account is provided by the operator).

WAN Settings
Next
12
WAN Settings Lan Settings
3
WiFi 2.4G Finish
APN Config
PPPoE Static DHCP 4G
Username admin
Manual
APN 3gnet
admin
Password
2.4G Wireless
Next
SSID COMFAST_2224_2G
Password
Advanced Setting
Bandwidth 20MHz
Country
Channel
China
auto
Prev
12
WAN Settings Lan Settings
3
WiFi 2.4G Finish
Pls set the SSID and password for the device and click “Next” to
finish settings.