comfort air CH-18451 User manual

1
INSTRUCTION MANUAL
18" STAND FAN
CH-18451
READ AND SAVE THESE INSTRUCTIONS
For product information, question, or customer service
Call Toll Free: 1-800-624-3436
E-mail: [email protected]
Website: www.comfortairhelp.com
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire electric shock, and in
jury to persons, including the following. please read all instructions
before using the product:
1. The fan is only for intended use as described in this manual. All other uses not
recommended in manual may cause fire, electrical shock or injury to persons.
2. This fan is intended for household use only.
3. To protect against electrical shock, do not immerse fan, plug or cord into water or spray with
liquids.
4. Close supervision is necessary when any appliance is used by or near children.
5. Always unplug the fan when it is not in use, when moving fan from one location to another,
and before cleaning.
6. Avoid contacting moving parts. never insert fingers, pencils or other similar objects through
the guard.
7. Do not operate in the presence of explosive or flammable fumes.
8. Do not place fan or parts near an open flame, cooking or other heating appliances.
9. Do not operate fan with a damaged cord, plug or after the fan suffered malfunctions or has
been dropped or damaged in any manner.
10. The use of attachment not recommended by manufacturer may be hazardous.
11. Do not use outdoors.
12. Do not let cord hang over the edge of a table or counter, or let it touch any hot surfaces.
13. To disconnect, grip plug and pull from wall outlet , Never yank cord.
14. Do not operate without fan lattice properly in place.
15. Always use on a dry level surface.
16. This appliance is not intended for use by children or other persons without assistance or
supervision if their physical, sensory or mental capabilities prevent them from using it safely.
Children should be supervised to ensure that they do not play with the appliance.
17. If the supply cord is damaged ,it must be replaced by the manufacturer or its service agent
or similarly qualified person in order to avoid a hazard
18. This appliance has a polarized plug ( one blade is wider than the other) To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
DO NOT attempt to defect this safety feature.

2
WARNING
•TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK,
DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED
CONTROL DEVICE.
•UNPLUG OR DISCONNECT THIS FAN FROM THE POWER
SUPPLY BEFORE SERVICING.
ASSEMBLY INSTRUCTIONS:
1. Unscrew the Height Adjustment Control Collar from the Outer Pipe by turning
counter-clockwise, and set aside. Pull out the Inner Pipe all the way to the top.
(you may have to push it up from the bottom to get it up)
2. Set the base on a level dry surface remove the screws from the Base Cross Legs,
then install the Outer Pipe and match the 4 holes over the 4 screw holes on the
base and replace the 4 screws back onto the cross leg bars.
3. Place the Base Cover on through the column with the tabs/slots pointed
downward.
4. Replace the Height adjustment Control Collar and tighten by turning clockwise.
5. Place the switch box/fan motor into the top of the inner pipe, tighten the Set
Screw.
6. Unscrew the Grill Nut on the front of the motor by turning counterclockwise.
7. Mount the Rear Grill to the motor front cover by matching 3 holes on the guard to
the 3 round positioning knobs on the motor front cover. Push in firmly until the 3
knobs protrude through the 3 holes.
8. Replace and tighten the Grill Nut by turning nut clockwise to hold the Rear Grill in
place.
9. Put the Fan Blade onto the motor shaft by matching the shafts slots with the
blades slot, tighten the Blade with Blade Cap by turning it counterclockwise.
10. Test fan by rotating with your hands, make sure there isn’t any contact with the nut.,
the fan blade should rotate freely, otherwise repeat all steps again, beginning from
step(4).
11. Mount Front Safety Grill onto Rear Grill by hanging the top hook clip of front
guard over the top of the Rear Grill. Close the clasps all around the grill.
OSCILLATION:
The oscillation knob is located on the top of the motor housing, simply press the knob down to
start oscillating, and pull the knob up to stop oscillating
OPERATION:.
1. Set the fan on a level dry surface.
2. Plug the power cord into a standard AC wall outlet.
3. Press speed key to set the desired speed “HI” “MED” “LOW”.
4. Press“OFF”key to turn the fan off.
5. To start or stop fan head oscillating, press or pull the oscillating knob on the top of
the motor housing.
6. To change the air flow angle, move the head forward or backwards.
NOTES ABOUT CLEANING BLADES:
1. Always unplug the fan before cleaning, simply lift the clips on ring of the guards and remove
the front guard.
2. Use a soft cloth, moistened with a mild soap, to clean fan and guard. DO NOT use abrasive
cleaners.
3. DO NOT immerse fan in water and never allow water to dip into the motor component.
4. DO NOT use gasoline, thinner or other chemicals to clean the fan.