Comfort Pedic UC524 User manual

Power Lift & Recline Chair
OWNER’S MANUAL
Model UC522 & UC524
522+524-112817
Made in USA
Comfort Pedic
PO Box 4142
Bayamon, PR 00958
PH 1-877-266-2262
UC522 UC524

2
Safety Guidelines
The symbols below are used in the owner’s manual and/or on the product
to identify warnings and notify you of important safety information. Make sure
you read and understand them completely.
WARNING! Indicate(s) a hazardous situation which, if not
avoided, could result in death or serious injury. This icon is
represented as a black symbol on a yellow triangle with a
black border.
MANDATORY! Failure to perform mandatory actions could
cause personal injury and/or equipment damage. This icon
is represented as a white symbol on a blue dot with a white
border.
PROHIBITED! Indicate(s) an action(s) that should not be
performed under any circumstance. Failure to adhere could
cause personal injury and/or equipment damage. This icon is
represented as a black symbol with a red circle and red slash.
Safety Symbols
The symbols below identify warnings, mandatory actions, and prohibited
actions. They can be found in the owner’s manual and/or on the product. Make
sure you understand all safety labels before operating the product. Do not remove
safety labels from your product.
Read and follow
owner’s manual!
Pinch/Crush Point
Hazard!
Transformer
Crush Hazard!
Fire Hazard!
Child and/or Pet
Crush Hazard!
Adult, Child and/
or Pet Tip Over
Hazard!

3
Safety Guidelines
Class II Device!
Indoor use only!
Do Not Smoke!
Electrical hazard!
Do not dispose in trash!
Batteries required!

4
MANDATORY
READ THIS MANUAL FIRST BEFORE INSTALLING OR
OPERATING YOUR POWER LIFT AND RECLINE CHAIR.
Your power lift and recline chair has been engineered from the
leg levelers up to provide the ultimate in strength and reliability.
Great care has been taken to provide you with total comfort and safety. Each unit
is thoroughly inspected and tested prior to shipment.
WARNING
Your power lift chair is a medical device. Therefore, you are required
to exercise caution when operating it to ensure your personal safety
and that of others around you. The following are rules for the safe
operation of your power lift chair.
Care should be taken in the unpacking of this unit, so as not to cause
injury to persons or damage to the unit. Dispose of all plastic bags and
covers, as they can be a smothering hazard to small children.
Do not allow children or pets near the chair while
the chair is operating.
Do not allow children to play with or operate the
chair at any time.
Hand control should be unplugged and placed out of
the reach of children when the chair is not in use.
Do not flop down into the chair when getting into it, or while it is in
its lift position. Flopping down into the chair will damage it and could
cause personal injury.
Do not allow anyone to sit on your lap, or on the arm of the chair, or
on the footrest while in or operating the chair, as it may cause tipping
and could result in personal injury.
Do not place fingers or hands between the seat cushion and the inside
arm of the chair while sitting in the chair or when the chair is in
operation or plugged into a power source.

5
Do not retrieve fallen objects from inside or under the chair while the
chair is plugged into a power source.
Do not operate the chair if there are any persons,
pets or other obstructions under or in front of the
footrest, under the chair or behind the chair.
Do not position yourself, child and/or pet too high on
the chair while the chair back is reclined. This can
cause a tip over hazard. Make sure you are properly
fitted for the lift chair prior to operating the chair.
Do not smoke while operating, sitting or resting in the chair.
To reduce risk of electrical shock, do not immerse any of the
electrical components into a liquid, or spill any liquids onto electrical
components. Do not open any of the electrical components. There are
no serviceable parts.
Warranty will be void if any of the electrical components are opened
by other than a qualified service person.
Make sure the chair is placed at the specified distance from a wall/
corner (page 7). Failure to do so can damage the chair and will void
the warranty.
Do not use any type of electrical extension cord to plug your
chair into an electrical outlet. Make sure that all electrical
products and their wires are positioned away from your chair
as the metal lift frame mechanism could crush them and
create a fire hazard and/or may cause personal injury.
Do not operate your lift chair while intoxicated or taking medications
that impair your mental or physical abilities to operate the chair safely.
Consult with your doctor about any medications you are taking that
may affect the safe operation of the chair.
Do not operate this product if you have any medical conditions that
result in limited, debilitating mental or physical capacity. You should
consult your doctor before using this product.
Consult with your physician regarding using the Trendelenburg
position.

6
Setting UpChair JUSt OUt Of BOx
Transformer
Wrench
Chair Hand Control
After unpacking chair read the owners manual in its entirety before assembling
your chair. Remove the hand control from the white box and plug it into the
connector in the pocket of the chair as shown below.
Hang the hand control above coiled cord in the clip above the pocket. Plug the
connector below the coiled cord into the locking connector inside the pocket.
Close the latch.

7
inStallatiOn OfYOUr lift Chair
MOdelS UC522, UC524
L.E.D. light
L.E.D. light
From motor
To outlet
115-120V A.C.
DC Power
Bottom view of
Transformer
Transformer
Plug
Install two 9 volt batteries
in transformer for battery
backup (batteries not
included)
1. Remove the transformer from the transformer box and install two 9 volt
alkaline batteries into the sockets on the transformer. (located under the
chair). Place transformer on floor behind chair.
2. Plug the transformer into a 115-120V 60Hz A.C. outlet and connect the power
cable from the chair into the transformer as shown. Power cable is located
under the chair attached to the motor with a white zip tie. Remove zip tie, and
extend the cable under and out behind the chair.
Wall
Side
View
Corner
To p
View
19" 19" 19"
3. Install the chair back per
“Assembly Instruction for
Joining Back to Chair.” (page 5)
4. Connect Heater Vibrator
System per “Connecting the
Heat and Massage Unit.”
(page 6)
Battery Back Up System
Your power chair comes with a battery back up in the advent of a household
power failure, the batteries have enough energy to bring the chair to a seated
position from the recline position. The batteries do not have enough energy nor
are they intended to operate the chair for an prolonged period of time in the absence
of standard household voltage (120 volt, 60 Hz). Batteries should be replaced
after one use. Batteries should be changed yearly.
5. Place the chair in the desired position in the room, keeping it 19” away from
the wall. If placing the chair into a corner keep it 19” from the wall as shown.
6. Adjust the leg levelers on the bottom of the chair if necessary to level the
chair. Some high pile carpets can obstruct the footrest operation by rubbing
against it. Adjust the levelers to a height above the pile.

8
Step 1: Plug in chair
Step 2: Press the down
arrow on the hand
control until the
footrest is about
parallel to the floor.
This will expose the
back brackets at the
rear of chair.
Step 3: Remove the foam
and flange lock nuts
from the threaded
studs on the back.
Slide the back
down between the
brackets until the
threaded studs on
the back slip thru
the holes in the
brackets as shown.
Step 4: Thread the flange
lock nuts onto the
studs and tighten
securely using the
supplied wrench or a
7/16" box wrench.
Step 5: Return the chair to
the seated upright
position by pressing
the up arrow on the
hand control.
Step 6: Attach the bottom
of the outside back
to the Velcro on the
arm cross rail.
Assembly Instructions for Joining Back to Chair
12
3
4 5

9
L.E.D. light
(batteries not included)
Making Power Connections In Your New Lift Chair
Models UC542-ME6
1. Install two 9 volt alkaline batteries in the inline battery holder as shown. The
battery holder is zip tied (white) to the rear of the metal frame. Cut the white
zip tie and extend the cable under and out behind the chair.
2. Remove the transformer from the transformer box follow steps 1, 2 and 3 on
page 4 to connect the transformer to the chair and AC outlet.
3. Place the chair in the desired position in the room, leaving the chair a safe
distance from the wall. See chair location on page 4 for the proper distance
from the wall.
4. Adjust the leg levelers on the bottom of the chair if necessary. Some high pile
carpets can obstruct the footrest operation by rubbing against it. Adjust the
levelers to a height above the pile.
P
A
T
E
N
T
E
D
CONNECTING THE HEAT AND MASSAGE UNIT
Plug the heating pad
and vibrator motors
in by plugging the red
connectors together
(heating pad) and the
green connectors
together (vibrator mo-
tor) as shown.

10
Hand Control Operation Models UC552, UC524, UC542-ME6
The PWR button needs to be turned on to activate all the functions of
the hand control.
To turn the power on to the hand control, press the PWR button at the top
of the hand control. The PWR button will glow green. To turn off the power
to the hand control, press the PWR button again. PWR button will glow blue.
Activating the hand control starts a 20 minute timer. To restart the timer after it
shuts off, press the PWR button again. Lights will dim to conserve energy after
about 10 seconds of non use.
Power Lock out
To lock the hand control, press and hold the PWR button for 4 seconds. The
button will glow red.
To unlock the hand control, press and hold the PWR button for 4 seconds. The
button will glow blue. After unlocking the hand control, you will need to press
the PWR button to turn on the power to the hand control.
To recline your chair or lower it from the lift position, press the down arrow
and hold until you reach your desired position. Then release the button.
To return to a seated position from recline or to lift your chair to a standing
position, press the up arrow and hold until you reach your desired position.
Then release the button.
Heat and massage operation
Press the MSG button to turn on the vibrators. Press
the MSG button again to turn off the vibrators.
Press the Heat button to turn the heating pad on.
Press the heat button again to turn off the heating
pad.
The heat and massage work independent of each other
and can be used separately or together and are factory
set to turn off in 20 minutes. If you desire an additional
20 minutes you will need to press the buttons again
to reactivate the heat and/or massage functions. Heat
and vibration turn off when the up and down arrows are
activated. Heat and vibration resume when the up and
down arrows are released.
Note: Your power lift chair can be stopped at any
time during lift or recline by releasing the selected button. The motor
is set to shut off when it reaches its fully extended or fully retracted
position if the selected button is not released. If you should go past your
desired position, select the button to bring you back to your desired
position. You can repeat the process as often as you like.

11
Should you ever encounter a problem with the operation of your lift
chair, such as mechanical or electrical problems, discontinue all use of
the product upon discovery of the problem. Contact the provider from
whom you purchased your chair. They will be able to resolve problems
and take care of service if needed.
NOTICE
To reduce the risk of potential product damage:
Follow these instruction to help ensure product quality over the life of the
system. Failure to follow these instructions may invalidate the warranty.
Do not attempt to disconnect the power cord by pulling the power cord.
Always hold the power plug and pull it out.
Only use replacement parts specified by your provider. Unauthorized
substitutions may result in fire, electrical shock or injury and will void the
warranty. Only use the power supply that accompanied this system.
If their is a malfunction of any kind, please contact your provider for further
instructions, and for returning it for examination, repair or replacement.
WARNING
To reduce the risk of fire or electrical shock, do not expose this product or
any components of this product to rain or moisture.
Do not spill liquid on the system. Spilled liquid may damage the system.
Do not reach for any portion of the system that has fallen into water or any
other liquid. Unplug immediately. Contact provider for service.
Use the power cord provided only. Do not overload wall outlets. The
power outlet used for this product should be readily accessible for fast
disconnection in case of an emergency.
Unplug the power supply should you find it necessary to clean or move the
product. We strongly recommend using only a clean dry cloth.
You should unplug the system when it will not be used for a long period of
time.
Keep all cords away from heated surfaces and pinch points.
Any changes or modifications to your system, or use of unauthorized
accessories to your system not expressly approved by the manufacturer
may be dangerous and voids any applicable warranties.
Close supervision is recommended when this product is used near children,
invalids, or disabled persons. Always check the skin in contact with the
heated area of this product.
Do not use outdoors. FOR INDOOR USE ONLY.

12
CONSUMER LIFETIME AND SEVEN YEAR LIMITED WARRANTY
Comfort Pedic, through its authorized distributor/service organization, warrants
this chair to the original consumer only, against defects in material or workmanship
as follows:
Lifetime Warranty
ComfortPedicwarrantsforthelifetimeofthechairbytheoriginalconsumertorepairor
replaceattheiroptiontheLiftMechanism,ChairFrameandReclineMechanism.Labor
to replace these parts is subsidized on all models. UC522, UC524 and UC542-ME6
are subsidized for a period of three years on above parts.
Three Year Parts Warranty
Comfort Pedic warrants the electrical parts of this chair against defect to original
consumer only as follows: Comfort Pedic power recline lift chair is limited to
three year electrical warranty. Labor to replace these parts is subsidized for one
year on all models. Replacement of the hand control and/or the transformer is
expected to be done by the consumer.
Limited Warranty Fourth Through Seventh Year
During the period beginning with the expiration of the full three year parts
warranty offered above and continuing through the seventh year after date of
original purchase by a consumer, Comfort Pedic will warrant the electrical parts
on the following pro-rated basis. Year 4 earns a 35% discount off suggested retail
price. Year 5 earns a 25% discount. Year 6 earns a 15% discount and year 7 a 5%
discount. By way of example, a part costing $100.00 that needs replacement in
year 4 would cost $65.00.
Terms Applicable to Warranties
Comfort Pedic will, at its option, repair and/or replace the defective parts and/
or components provided that the warranty parts have not been subjected to
misuse, abuse or improper service by the consumer; have not been damaged
in transit or handling, and/or have not been altered or repaired by unauthorized
representatives. This warranty does not include costs for unnecessary service
calls, i.e., service calls solely for the purpose of educating the consumer about
the product, or finding an unsatisfactory power connection, etc. Exceeding
the weight capacity of the chair (published in each owner’s manual) will void
all warranties. Fabric shading cannot be guaranteed for replacement parts or
replacement chairs.
Weight Capacity Model UC522, UC524.....................375 lbs.
Model UC542-ME6 .........................500 lbs.
Comfort Pedic will pay standard shipping rates on all warranted parts for the first
year. The consumer will be responsible to pay cost for transportation, handling and
packaging of the parts or components beyond the first year. Comfort Pedic shall
not be responsible or obligated to pay for any costs or expenses for examination
of any Warranted parts. All repairs and labor rates must be approved by Comfort
Pedic before service is provided. Any repairs by unapproved or unauthorized
representatives will void all warranties.

13
CARE AND MAINTENANCE
Your lift chair will require routine maintenance checks. You can perform some
of these checks, while others may require assistance from a provider. By
following these maintenance checks, you can make sure your lift chair gives
you years of trouble-free operation. If you have any questions or concerns
regarding your lift chair’s care and maintenance, contact your provider.
9Before cleaning your lift chair, consult your provider for the proper types
of cleaner and cleaning methods.
9Keep all electrical components free from moisture and liquid spills.
Intended for indoor use only.
9Periodically inspect all wiring harnesses to make sure they are not cut,
damaged, frayed, or disconnected. If damage of any type is present,
unplug the lift chair and contact your provider.
9Periodically check all fasteners for tightness, wear, and corrosion. If any
of these are present, unplug the lift chair and contact your provider.
Warning: Be careful of pinch points and sharp metal parts (wear
gloves).
9Replace the batteries after one use. Replace the batteries yearly, even if
they were not used. Batteries are intended for one use only!

14
#
Please fill in your Power Lift & Recline Chair information below. This
information will be useful in the event that you should ever need to
contact your provider concerning your lift chair.
Date of Purchase _____________________________________________
Model ______________________________________________________
Serial Number _______________________________________________
Your representative or provider
Name ______________________________________________________
Company ___________________________________________________
Address ____________________________________________________
____________________________________________________________
CAUTION
Do not allow children to play on this mechanized
furniture or operate the mechanism.
Leg rest folds down on closing so that a child could
possibly be injured.
Always leave chair in a sitting position. Keep hands
and feet clear of mechanism. Only the occupant
should operate it.
fOr YOUr reCOrdS

15
Register your power lift chair by filling out this warranty card within 30 days
of purchase date and returning to the address on the back. Be sure to keep
copies of this registration so you have all the information to refer back in case
you experience a problem with your chair.
Name __________________________________________________________
Address ________________________________________________________
City ___________________________________State_____ Zip ____________
Purchase Date ___________________________________________________
Model No. & Size ________________________________________________
Serial Number ___________________________________________________
Provider’s Name _________________________________________________
Address ________________________________________________________
________________________________________________________________
Why did you choose this power lift chair?
Appearance Price Provider Reputation
Additional Comments _____________________________________________
________________________________________________________________
________________________________________________________________
Remember to read your owner’s manual carefully before you operate your chair.
If you need help or additional information please contact your provider.
COnSUMer One Year WarrantY
#

#
Comfort Pedic PO Box 4142 Bayamon, PR 00958
PLACE
STAMP
HERE