Commscope Ion-e series User manual

ION®-E Series Hardware

Installation Guide • M0201AAA • June 2017

DISCLAIMER

ThisdocumenthasbeendevelopedbyCommScope,andisintendedfortheuseofitscustomersandcustomersupport

personnel.Theinformationinthisdocumentissubjecttochangewithoutnotice.Whileeveryefforthasbeenmadeto

eliminateerrors,CommScopedisclaimsliabilityforanydifficultiesarisingfromtheinterpretationoftheinformation

containedherein.Theinformationcontainedhereindoesnotclaimtocoveralldetailsorvariationsinequipment,norto

provideforeverypossibleincidenttobemetinconnectionwithinstallation,operation,ormaintenance.Thisdocument

describestheperformanceoftheproductunderthedefinedoperationalconditionsanddoesnotcovertheperformance

underadverseordisturbedconditions.Shouldfurtherinformationbedesired,orshouldparticularproblemsarisewhichare

notcoveredsufficientlyforthepurchaser'spurposes,contactCommScope.

CommScopereservestherighttochangeallhardwareandsoftwarecharacteristicswithoutnotice.

©2017CommScope,Inc.AllRightsReserved.

Thisdocumentisprotectedbycopyright.Nopartofthisdocumentmaybereproduced,storedinaretrievalsystem,or

transmitted,inanyformorbyanymeans,electronic,mechanicalphotocopying,recording,orotherwisewithouttheprior

writtenpermissionofCommScope.

Forpatentsseewww.cs-pat.com.

TRADEMARKS

Alltrademarksidentifiedby®or™areregisteredtrademarksortrademarks,respectively,ofCommScope,Inc.Namesof

otherproductsmentionedhereinareusedforidentificationpurposesonlyandmaybetrademarksand/orregistered

trademarksoftheirrespectivecompanies.

AndrewWirelessSystemsGmbH,30-June-2017

This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED

INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.

Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000

for each continuing violation.

This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED

INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.

You MUST register Class B signal boosters (as defined in 47 CFR 90.219) online at

www.fcc.gov/signal-boosters/registration. Unauthorized use may result in significant forfeiture penalties,

including penalties in excess of $100,000 for each continuing violation.

M0201AAA CPRI Digital Interface Unit Installation and Provisioning Guide

1 Using this Document ____________________________________________________________________________________1

Document Revision History ................................................................................................................................................................................... 2

Document Cautions and Notes.............................................................................................................................................................................. 3

Abbreviations Used in this Guide .......................................................................................................................................................................... 4

2 ION-E Series Hardware Overview __________________________________________________________________________5

ION-E Series System Overview .............................................................................................................................................................................. 6

Safely Working with ION-E Hardware ................................................................................................................................................................... 9

Equipment Symbols with CE Compliance ......................................................................................................................................................... 9

Health and Safety Precautions ......................................................................................................................................................................... 9

Property Damage Warnings ........................................................................................................................................................................... 10

Compliance and Standards Certification ............................................................................................................................................................. 11

FCC RF Exposure Requirements...................................................................................................................................................................... 11

EMC Standards ............................................................................................................................................................................................... 11

FCC and IC Standards...................................................................................................................................................................................... 12

3 WCS-2 and WCS-4 Subracks and Modules __________________________________________________________________13

WCS-2 and WCS-4 Subracks and Modules ..........................................................................................................................................................14

WCS Subrack Front Panel Card Slots and GUI Identification .......................................................................................................................... 15

WCS Subrack Back Panel Connectors .............................................................................................................................................................16

WCS Subrack Alarm Connector....................................................................................................................................................................... 17

WCS Fan Modules and Filters ......................................................................................................................................................................... 18

System User Interface Card (SUI) ................................................................................................................................................................... 19

RF Donor Card (RFD)....................................................................................................................................................................................... 20

Optical Transport Card (OPT).......................................................................................................................................................................... 21

Copper Transport Card (CAT).......................................................................................................................................................................... 22

Auxiliary Unit Transport Card (AUT) ............................................................................................................................................................... 23

Installing Subracks and PSUs in an Equipment Rack ........................................................................................................................................... 24

Rack-Mounting the Subracks and PSU............................................................................................................................................................24

Connect the Subrack and PSU Power and Communication Cables ................................................................................................................ 25

Install the CAN and TEN Cards........................................................................................................................................................................ 27

Install SFP+ Transceivers in the OPT Cards ..................................................................................................................................................... 28

Connect the RFD Cards ................................................................................................................................................................................... 29

Connect the CAT Cards ................................................................................................................................................................................... 30

Connect the AUT Cards................................................................................................................................................................................... 32

4 Point of Interface (e-POI) Subracks _______________________________________________________________________35

Point Of Interface (e-POI) Subrack ...................................................................................................................................................................... 36

e-POI Subrack Back Panel Connectors............................................................................................................................................................ 36

Interface Card (IFC)......................................................................................................................................................................................... 37

e-POI Module.................................................................................................................................................................................................. 38

Installing an e-POI Subracks and Modules .......................................................................................................................................................... 39

Removing an e-POI Module from an e-POI Subrack............................................................................................................................................ 40

e-POI Subrack and Component Specifications ....................................................................................................................................................41

5 Power Supply Unit (PSU)________________________________________________________________________________43

Power Supply Unit (PSU) ..................................................................................................................................................................................... 44

PSU Modules and Connectors ........................................................................................................................................................................ 44

12 Vdc Power Module LEDs............................................................................................................................................................................ 45

57 Vdc Power Module LEDs............................................................................................................................................................................ 46

Installing PSUs ..................................................................................................................................................................................................... 47

TABLE OF CONTENTS

CPRI Digital Interface Unit Installation and Provisioning Guide M0201AAA Issue 1

Page iv © June 2017 CommScope, Inc.

Table of Contents

6 Universal Access Points_________________________________________________________________________________49

Identifying UAPs in the ION-E Software ......................................................................................................................................................... 50

UAPs and UAP-N25s ....................................................................................................................................................................................... 51

UAP-X.............................................................................................................................................................................................................. 52

Installing UAPs..................................................................................................................................................................................................... 53

Using the UAP Ceiling Mount Assembly (PN 7683182-00) ............................................................................................................................. 53

Required Tools for a Standard UAP Ceiling Mount .................................................................................................................................. 53

Unpack and Inspect the Ceiling Mount Assembly.................................................................................................................................... 53

Standard Ceiling Mount Overview ........................................................................................................................................................... 54

Standard Ceiling Mount Installation Steps............................................................................................................................................... 55

Mounting a UAP Using a UAP Quick Release Ceiling Mount Kit..................................................................................................................... 57

Required Tools for a Quick Release Ceiling Mount Kit............................................................................................................................. 57

Unpack and Inspect the Quick Release Ceiling Mount Kit ....................................................................................................................... 58

Overview of Using a Quick Release Ceiling Mount Kit ............................................................................................................................. 58

Mount the UAP to the Ceiling ..................................................................................................................................................................59

Connect the UAP Cables........................................................................................................................................................................... 61

Install the UAP.......................................................................................................................................................................................... 62

Mounting a UAP to a Wall Using the UAP Wall Mounting Kit (PN 7683181-00) ............................................................................................ 63

Required Tools for a Wall Mount............................................................................................................................................................. 63

Unpack and Inspect the Wall Mounting Kit.............................................................................................................................................. 64

Mount the UAP to a Wall ......................................................................................................................................................................... 64

UAP, UAP-N25, and UAP-X Cable Requirements............................................................................................................................................ 67

Cascading a UAP, UAP-X, or UAP-N25 ............................................................................................................................................................68

UAP Maintenance................................................................................................................................................................................................ 69

Remove a UAP from a Ceiling Mount .............................................................................................................................................................69

Remove a UAP from a Wall Mount................................................................................................................................................................. 70

Preventative UAP Maintenance ..................................................................................................................................................................... 71

UAP Specifications............................................................................................................................................................................................... 72

UAP Output Specifications.............................................................................................................................................................................. 72

UAP Bandwidth Specifications........................................................................................................................................................................ 73

7 Carrier Access Point, Low Power (CAP L) ___________________________________________________________________75

Identifying CAP Ls in the ION-E Software ............................................................................................................................................................ 76

CAP L Overview............................................................................................................................................................................................... 77

CAP L Connectors, Ports, and LEDs........................................................................................................................................................... 78

CAP L with an Optical Fiber Interface....................................................................................................................................................... 79

CAP L with a Copper Interface and External DC Power............................................................................................................................ 80

CAP L with a Copper Interface and Power Cat 6A Cable .......................................................................................................................... 81

Fan Interface Port..................................................................................................................................................................................... 82

Powering a CAP L...................................................................................................................................................................................... 82

CAP L Accessory Options .......................................................................................................................................................................... 83

Fan Kit (PN 7724090-00) .................................................................................................................................................................... 84

CAP L Flat Mounting Bracket Kit (PN 7774353-00) ............................................................................................................................ 85

CAP L Power Supply / Hybrid Fiber Mounting Kit (PN 7774354-00) .................................................................................................. 86

CAP L 240W AC/DC Power Supply Kit (PN 7775087-00) .................................................................................................................... 87

CAP OCTIS Kits (PNs 7773582-00 and 7760652-00)........................................................................................................................... 88

Installing CAP Ls................................................................................................................................................................................................... 89

Prepare for Installation................................................................................................................................................................................... 89

Recommended Tools................................................................................................................................................................................ 89

Recommended Materials.........................................................................................................................................................................89

Determine the Power Consumption of the CAP L.................................................................................................................................... 90

Determine the CAP L Mounting Site ........................................................................................................................................................ 90

Mounting Orientation .............................................................................................................................................................................. 93

Mounting Cautions................................................................................................................................................................................... 95

General Installation Safety Requirements ............................................................................................................................................... 95

Guard Against Damage from Electro-Static Discharge............................................................................................................................. 95

Unpack and Inspect the CAP L and Optional Accessories ........................................................................................................................ 96

M0201AAA CPRI Digital Interface Unit Installation and Provisioning Guide

Table of Contents

Installing a CAP L.............................................................................................................................................................................................96

Mount the CAP L ...................................................................................................................................................................................... 96

Flat-Surface Mount a CAP L ............................................................................................................................................................... 97

Wall Mount a CAP L Using a Flat Mounting Bracket Kit (PN 7774353-00)......................................................................................... 97

Wall Mount a CAP L Using a Power Supply / Hybrid Fiber Mounting Kit (PN 7774354-00)............................................................. 100

Wall Mount a CAP L Using a 240W AC/DC Power Supply Kit (PN 7775087-00)...............................................................................106

Ceiling Mount a CAP L......................................................................................................................................................................109

(Optional) Ground the CAP L..................................................................................................................................................................110

Connect the CAP L Cables....................................................................................................................................................................... 111

Cable a CAP L with an Optical Fiber Interface..................................................................................................................................111

Cable a CAP L with a Copper Interface and Power over Category 6A Cable.................................................................................... 114

Cable a CAP L with a Copper Interface and Power over Ethernet ...................................................................................................116

Cascading CAP Ls ...............................................................................................................................................................................................118

CAP L Maintenance ...........................................................................................................................................................................................119

Remove a CAP L from a Ceiling Mount......................................................................................................................................................... 119

Remove a CAP L from a Wall Mount ............................................................................................................................................................ 120

Preventative CAP L Maintenance ................................................................................................................................................................. 121

CAP L Specifications........................................................................................................................................................................................... 122

CAP L Output Specifications ......................................................................................................................................................................... 122

CAP L Bandwidth Specifications.................................................................................................................................................................... 123

8 DCCS Global Technical Support__________________________________________________________________________125

Contacting DCCS Global Technical Support....................................................................................................................................................... 126

Telephone Helplines..................................................................................................................................................................................... 126

Online Support..............................................................................................................................................................................................126

DCCS Technical Training .................................................................................................................................................................................... 127

Accessing ION-E Series User Documentation.................................................................................................................................................... 128

Hardware to Software Mapping Information.................................................................................................................................................... 129

CPRI Digital Interface Unit Installation and Provisioning Guide M0201AAA Issue 1

Page vi © June 2017 CommScope, Inc.

Table of Contents

M0201AA ION®-E Series Hardware Installation Guide

Chapter Topics Page

Thischapterprovidesinformationonhowtousethishardwareinstallationguide.

USING THIS DOCUMENT 1

ION®-E Series Hardware Installation Guide M0201AA

Page 2 © June 2017 CommScope, Inc.

Document Revision History

DOCUMENT REVISION HISTORY

Document # Document Date Technical Updates

M0201AAA June 2017 Initial release. Introduces the new Carrier Access Point, Low Power (CAPL), and replaces the

following ION-E Series user documentation:

• hardware section of the ION-E Series Software Version 2.0.0 User’s Manual (PN M0201A0D)

•ION-E Series Instructions for WCS Subracks (PN M0201A1C)

•ION-E Series Instructions for Ceiling Mount UAP (PN M0201A2A)

•ION-E Series Instructions for UAP Wall Mount (PN M0201A3B)

•ION-E Series Instructions for UAP (PN M0201A4A)

•ION-E Series Instructions for SUI, RFD, CAT, OPT, and AUT Cards (PN M0201A5B)

•ION-E Series Instructions for e-POI (PN M0201A7B)

•ION-E Series Instructions for UAP Quick Release Ceiling Mount (PN M0201A8A).

M0201AA ION®-E Series Hardware Installation Guide

Document Cautions and Notes

DOCUMENT CAUTIONS AND NOTES

Thisdocumentcontainsnotes,cautions,andwarnings.Ingeneral,cautions,warnings,andnotesindicatethe

following:

The icon to the left is used to indicate a caution or warning. Cautions and warnings indicate operations or

steps that could cause personal injury, induce a safety problem in a managed device, destroy or corrupt

information, or interrupt or stop services.

The icon to the left indicates a caution or warning that pertains to laser equipment.

The icon to the left is indicates a caution or warning that pertains to Radio Frequency (RF).

The icon to the left is indicates a Note. Notes provide information about special circumstances.

ION®-E Series Hardware Installation Guide M0201AA

Page 4 © June 2017 CommScope, Inc.

Abbreviations Used in this Guide

ABBREVIATIONS USED IN THIS GUIDE

AUT Auxiliary Transport LED Light Emitting Diode

AUX Auxiliary MHz Megahertz

CCelsius Mm Millimeter

CAN Central Area Node MMF Multi-Mode Fiber

CAP L Carrier Access Point, Low Power NC Normally Closed

Cat Category NO Normally Open

CAT Copper Transport OAP Optimized Access Point

COM Communication or Common OPT Optical Transport

dB Decibel PN Part Number

dBc Decibels (referenced to the carrier) PoCAT Power over Cate-gory 6A cable

dBm Decibel-milliwatts PoE Power over Ethernet

DC Direct Current POI Point of Interface

EFTA European Free Trade Association RAN Regional-Area Network

EMC Electromagnetic Compatibility RF Radio Frequency

EU European Union RFD RF Donor

FFahrenheit RTN Return

FCC Federal Communications Commission RU Rack Unit

Gb Gigabyte SFP Small Form-Factor Pluggable

Gbps Gigabits per second SMF Single-Mode Fiber

GHz Gigahertz SUI System User Inter-face

IC Industry Canada TEN Transport Expan-sion Node

IFC Interface Card UAP Universal Access Point

kg Kilogram Vdc Volts, direct cur-rent

LCD Liquid-Crystal Display WWatts

M0201AA ION®-E Series Hardware Installation Guide

Chapter Topics Page

Equipment Symbols with CE Compliance ......................................................................................................................................................... 9

Property Damage Warnings ........................................................................................................................................................................... 10

Compliance and Standards Certification ............................................................................................................................................................. 11

FCC RF Exposure Requirements...................................................................................................................................................................... 11

ThischapterprovidesinformationontheseparatehardwarecomponentsthatanION-ESeriessystemcan

comprise.

ION-E SERIES HARDWARE OVERVIEW 2

ION®-E Series Hardware Installation Guide M0201AA

Page 6 © June 2017 CommScope, Inc.

ION-E Series System Overview

ION-E SERIES SYSTEM OVERVIEW

TheION-EisaunifiedwirelessinfrastructureplatformdefinedaroundITbasedarchitecture.Itbrings

togetherlicensedwirelessandpower,plusGigabitEthernetforWiFiintoonewirelesssystemthatcanscale

tobuildingsizeandistechnologyandspectrumagnosticandadaptive.

AbasicION-Esystemcomprisesthefollowingmaincomponents,asshowninFigure2-1.

•CentralAreaNode(CAN)—providesserver-levelcontrolandprimarysignaldistribution.2Uand4U

subrackoptionsareavailable.

•TransportExpansionNode(TEN)—connectstoaCANusingMulti-ModeorSingle-Modefiberasa

secondarydistributionpoint.2Uand4Usubrackoptionsareavailable.

•AccessPoint—connectsCAN/TENtoantennasorotherwirelessdevices,andcanbeanyofthefollowing.

–UniversalAccessPoint(UAP)—connectstheCAN/TENtoaninternalantenna;receivesdataand

powerthroughCategory6Atwistedpaircabling.SupportsGigabitEthernetforWiFi,IPcameras,or

otherdevicesinadditiontowirelessoveracommoncable.

–UAP-X—connectstheCAN/TENtoanexternalantenna;otherwisefunctionsthesameasthe

standardUAP.

–CarrierAccessPoint,LowPower(CAPL)—interfaceswiththeCAN/TENviaaCAT6Acable,orvia

anopticallink.Onthedownlink,theCAPLconvertssomeorallofthedataarrivingattheCAPLto

analogsignalsandsendsthemtotheanantenna.Ontheuplink,receivedsignalsaredigitizedand

serializedintodatastreamswhicharesentbacktotheCAN/TEN.EachCAPLcontainsuptofour

transceiverpathsforRFcoverage.

Figure 2-1. Basic ION-E System

A WCS-2 and a WCS-4 can be configured for use as a CAN or a TEN. When the information in this guide

applies to both configurations, the term “CAN/TEN” is used. When the information pertains to only one

of the configurations, that configuration will be identified singularly as “CAN” or “TEN.”

CAN TEN WiFi IP CameraUAP MM/SM Fiber

Cat6A

M0201AA ION®-E Series Hardware Installation Guide

ION-E Series System Overview

TheinformationinthisdocumentguidesyouthroughtheinstallationofaCommScopeION®-Esystem,which

supportstheION-EsystemcomponentsidentifiedinTable2-1onpage8(componentgraphicsarenotscaled

tosize).

ForinformationonhowtofindtheminimumsoftwarerequirementsforION-Ehardware,referto"Hardware

toSoftwareMappingInformation”onpage129.

ION®-E Series Hardware Installation Guide M0201AA

Page 8 © June 2017 CommScope, Inc.

ION-E Series System Overview

Table 2-1. ION-E Series Hardware System Components Supported in this Manual

Component Description

WCS-4 Subrack—CAN or TEN The WCS-4 Subrack is typically used as a CAN but can also serve as a TEN.

WCS-2 Subrack—TEN or CAN The WCS-2 Subrack is typically used as a TEN, but can also serve as a CAN.

System User Interface Card (SUI) The SUI provides local and LAN Ethernet connections and a USB port.

RF Donor Card (RFD) The RFD is the interface for RF signals between the CAN and the BTS or

eNode-B. Its four QMA female ports simultaneously transmits and receives

signals.

Optical Transport Card (OPT) The OPT provides a 10 Gb fiber connection between a CAN/TEN. Each OPT

Card supports up to four SFP+ transceivers.

Copper Transport Card (CAT) The CAT Card provides 10 Gb Cat6A connections between the CAN/TEN and

the UAP.1 CAT Cards also supply the remote power over Cat6A to the UAPs.

Each CAT Card supports a maximum of six UAPs.

Auxiliary Unit Transport Card

(AUT)

The AUT Card provides a 1 Gb pass-through connection between the

CAN/TEN and the UAP for WiFi, IP cameras, or other 1 Gb Ethernet devices

(and 100Mb devices in a future release).

Power Supply Unit (PSU) The PSU houses two 12 Vdc Power Modules and two 57 Vdc Power Modules,

which supply power to the WCS subracks, UAPs, and connected devices.

12 Vdc Power Module A 12 Vdc Module plugs into the Power Supply Subrack to provide 12 Vdc

power to the WCS and e-POI subracks.

57 Vdc Power Module A 57 Vdc Module plugs into the Power Supply Subrack to provide remote

power over Cat6A for the UAP and devices connected to the UAP.

UAP, UAP-N25 The Universal Access Point (UAP), which is connected to the ION-E system via

Cat6A cabling, uses its internal antennas to transmit and receive over-the-air

signals. It also supports Ethernet backhaul or an additional UAP through a

second RJ45 jack.

UAP-X The UAP-X is functionally identical to the UAP, but is designed to work with

external antennas. A UAP-X has two QMA Female antenna ports that connect

to external antennas, one each for Transmit (TX) and Receive (RX).

CAP L Carrier Access Point, Low Power (CAP L) provides data and power through

Copper, Single-Mode Fiber (SMF), or Multi-Mode Fiber (MMF), and supports

Gigabit Ethernet for WiFi, IP cameras, or other devices in addition to wireless

over a common cable.

Fan Module The Fan Tray and Filter Modules cool the WCS and all of its Cards.

• An AWCS-2 requires one Fan Tray.

• A WCS-4 requires two Fan Trays.

e-POI Subrack The e-POI Subrack supports up to eight e-POI RFMs and one IFC Module.

Point of Interface Card

(e-POI RFM)

The e-POI-RFM Card is a low PIM attenuator that reduces high power RF

signals from their source by 30 dB to interface with the RFD Cards.

Interface Card (IFC) The IFC is used to set the subrack number of the e-POI subrack. It also

provides a Status LED for each of the e-POI Modules in the subrack.

1 Unless otherwise noted, the use of “AP” collectively refers to the UAP, UAP-X, UAP-N25, and CAPs.

M0201AA ION®-E Series Hardware Installation Guide

Safely Working with ION-E Hardware

SAFELY WORKING WITH ION-E HARDWARE

Thefollowingsectionsprovideimportantinformationthatyoushouldreadandknowbeforeworkingwith

anyION-Ehardware.

Equipment Symbols with CE Compliance

Table2-2identifiestheCEmarkingsusedonION-Ehardwareanddefineswhatthesemarkingsmean,

includingrequiredusercompliance.

Health and Safety Precautions

Observeallcautionsandwarningslistedinthissection

Table 2-2. CE Compliance Labels

Symbol Meaning

Alert sign to R&TTE

To be sold exclusively to mobile operators or authorized installers - no harmonised frequency

bands, operation requires license.

Intended use: EU and EFTA countries

Indicates conformity with the R&TTE directive 1999/5/EC certified by the notified body no. 0700.

A High leakage current ground (earth) connection to the Power Supply Subrack is essential before

connecting the supply.

Laser radiation. Risk of eye injury in operation. Do not stare into the laser beam; do not view the laser

beam directly or with optical instruments.

High frequency radiation in operation. Risk of health hazards associated with radiation from the

antenna(s) connected to the unit. Implement prevention measures to avoid the possibility of close

proximity to the antenna(s) while in operation.

ION®-E Series Hardware Installation Guide M0201AA

Safely Working with ION-E Hardware

Property Damage Warnings

Due to power dissipation, the power supply units may reach a very high temperature if not properly

ventilated. Do not operate this equipment on or close to flammable materials.

ESD precautions must be observed. Before commencing maintenance work, use the available grounding

(earthing) methodology to connect ESD protection measures.

Keep operating instructions within easy reach and make them available to all users.

Only license holders for the respective frequency range are allowed to operate this unit.

Read and obey all the warning labels attached to the unit. Make sure that all warning labels are kept in a

legible condition. Replace any missing or damaged labels.

Make sure the unit's settings are correct for the intended use (refer to the manufacturer product

information) and regulatory requirements are met. Do not carry out any modifications or fit any spare

parts, which are not sold or recommended by the manufacturer.

M0201AA ION®-E Series Hardware Installation Guide

Compliance and Standards Certification

COMPLIANCE AND STANDARDS CERTIFICATION

FCC RF Exposure Requirements

Forinstallations,whichhavetocomplywithFCCRFexposurerequirements,theantennaselectionand

installationmustbecompletedinawaytoensurecompliancewiththoseFCCrequirements.Dependingon

theRFfrequency,ratedoutputpower,antennagain,andthelossbetweentherepeaterandantenna,the

minimumdistanceDtobemaintainedbetweentheantennalocationandhumanbeingsiscalculated

accordingtothisformula:

where

•P(mW)istheradiatedpowerattheantenna,i.e.themax.ratedrepeateroutputpowerinadditiontothe

antennagainminusthelossbetweentherepeaterandtheantenna.

•PD(mW/cm²)istheallowedPowerDensitylimitacc.to47CFR1.1310(B)forgeneralpopulation/

uncontrolledexposureswhichis

–f(MHz)/1500forfrequenciesfrom300MHzto1500MHz

–1forfrequenciesfrom1500MHzto100,000MHz

RFexposurecompliancemayneedtobeaddressedatthetimeoflicensing,asrequiredbytheresponsibleFCC

Bureau(s),includingantennaco-locationrequirementsof1.1307(b)(3).

EMC Standards

•ForinstallationsthathavetocomplywithEuropeanEN50385exposurecompliancerequirements,the

followingPowerDensitylimits/guidelines(W/m²)accordingtoICNIRParevalid:

–2forfrequenciesfrom10MHzto400MHz

–f(MHz)/200forfrequenciesfrom400MHzto2GHz

–10forfrequenciesfrom2GHzto300GHz

•ThisunitcomplieswithEuropeanstandardEN60950.

This is class A equipment. This equipment can cause radio interference in domestic areas. In this case the

operator can be asked to start preventive action.

]/[

][

4cmmW

cm PD

D∗∗

ION®-E Series Hardware Installation Guide M0201AA

Compliance and Standards Certification

FCC and IC Standards

Notice:ForinstallationsthathavetocomplywithFCC/IndustryCanadarequirements:

English

ThisdevicecomplieswithFCCPart15.Operationissubjecttothefollowingtwoconditions:(1)thisdevice

maynotcauseinterference,and(2)thisdevicemustacceptanyinterference,includinginterferencethatmay

causeundesiredoperationofthedevice.

ThisdevicecomplieswithHealthCanada'sSafetyCode.TheinstallerofthisdeviceshouldensurethatRF

radiationisnotemittedinexcessoftheHealthCanada'srequirement.Informationcanbeobtainedathttp:

//www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php.

Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe

user'sauthoritytooperatetheequipment.

Theantenna(s)usedforthistransmittermustbeinstalledtoprovideaseparationdistanceofatleast20cm

fromallpersonsandmustnotbeco-locatedoroperatinginconjunctionwithanyotherantennaor

transmitter.

French

CetappareilestconformeaFCCPartie15.SonutilisationestsoumiseaLesdeuxconditionssuivantes:(1)cet

appareilnepeutpasprovoquerd’interferenceset(2)cetappareildoitaccepterTouteinterference,ycompris

lesinterferencesquipeuventcauserunmauvaisfonctionnementdudispositif.

CetappareilestconformeavecSanteCanadaCodedesecurite6.Leprogrammed’installationdecetappareil

doits’assurerquelesrayonnementsRFn’estpasemisau-deladeI’exigencedeSanteCanada.Les

informationspeuventetreobtenues:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-fra.php

Leschangementsoumodificationsnonexpressementapprouvesparlapartieresponsabledelaconformite

pourraientannulerl'autoritedel'utilisateurautilisercetequipement.

Laoulesantennesutiliseesaveccetemetteurdoiventetreinstalleesavecuneseparationd’auminimum

20cmavectoutepersonneetnedoiventpasetreco-localiseesouutiliseesavectouteautreantenneoutout

autreemetteur.

ForaClassAdigitaldeviceorperipheral.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuantto

EN55022andpart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferencewhentheequipmentisoperatedinacommercialenvironment.

Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin

accordancewiththeinstructionmanual,maycauseharmfulinterferencetoradiocommunications.Operation

ofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillbe

requiredtocorrecttheinterferenceathisownexpense.