CompUSA 333628 User manual

54 Mbps Wireless G
Broadband Router
SKU: 333628
User’s Manual

1
FCC and CE Radiation Norm
FCC
This equipment has been tested and found to comply with limits for Class B digital device pursuant
to Part 15 of Federal Communications Commission (FCC) rules.
CE
This equipment has been tested and found to comply with the limits of the European Council
Directive on the approximation of the law of the member states relating to electromagnetic
compatibility (89/336/EEC) according to EN 55022 Class B.
FCC and CE Compliance Statement
These limits are designed to provide reasonable protection against frequency interference in
residential installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed or used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in television
reception, which can be determined by turning the equipment off and on. The user is encouraged
to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected to.
CAUTION!
The Federal Communications Commission warns the user that changes or modifications to the
unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.

2
Package Contents
- 54 Mbps Wireless G Broadband Router
- RJ-45 Cable
- Power Adapter
- Antenna
- Quick Installation Guide
- User’s Manual CD
System Requirements
- RJ-45 Connector Cables
- Web Browser Software
- Internet Access Requires Internet Service
- CD-ROM Drive (to access the User’s Manual)
Features
- High Internet Access throughput (50M)
- Allow multiple users to share a single Internet line
- Supports up to 253 users
- Internet Access via Cable or xDSL modem
- Access Private LAN Servers from the Public Network
- Equipped with four LAN ports (10/100Mbps) and one WAN port (10/100Mbps)
- Provides IEEE 802.11g/b wireless LAN access point
- Support DHCP (Server/Client) for easy setup
- Support advance features such as: Special Applications, DMZ, Virtual Servers, Access
Control, and Firewall.
- Allows you to monitor the router’s status such as: DHCP Client Log, System Log, Security
Log and Device/Connection Status
- Easy to use Web-based GUI for configuration and management purposes
- Remote Management allows configuration and upgrades from a remote site (over the Internet)

3
Installation
1) Setup your network as shown in the setup diagram below.
2) You then need to set your LAN PC clients so that they can obtain an IP address automatically. By default, the
Broadband Router’s DHCP server is enabled so that you can obtain an IP address automatically.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your
LAN. If there is another DHCP server on your network, then you’ll need to switch one of the DHCP servers off.
3) Once your PC has obtained an IP address from your router, enter the default IP address 192.168.2.1 (broadband
router’s IP address) into your PC’s web browser and press <enter> .
4) The login screen below will appear. Enter the “User Name” and “Password” and then click <OK> to login.
Note: By default the user name is “admin” and the password is “1234”. For security reasons it is
recommended that you change the password in “General setup/system/password” as soon as possible.

4
Chapter 1
Quick Setup
Once you have logged onto the Online Configuration page, you can configure the settings of your router with the
“Quick Setup Wizard”. The following are steps to configure some of the basic settings of your router.
Step 1) Time Zone
The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as
Log entries and Firewall settings.
Parameter Description
Set Time Zone Select the time zone of the region you are currently in. The router will set its
time based on your selection.
Time Server Address You can manually assign a time server address if the default time server is
unavailable.
Enable Daylight Savings The router can also take Daylight Savings into account. If you wish to use this
function, you must check the enable box to enable your Daylight Savings
configuration.
Start Daylight Savings Time Select the period in which you wish to start Daylight Savings Time
End Daylight Savings Time Select the period in which you wish to end Daylight Savings Time
After you have entered all the time settings, click on “NEXT” to proceed to step 2, Broadband Type.

5
Step 2) Broadband Type
Note: Different ISP’s require different methods of connecting to the Internet, please check with your ISP as to the type
of connection it requires.
Menu Description
1.1 Cable Modem Your ISP will automatically give you an IP address.
1.2 Fixed-IP xDSL Your ISP has given you an IP address already.
1.3 PPPoE Your ISP requires you to use a Point-to-Point Protocol over an Ethernet (PPPoE)
connection.
1.4 PPTP Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection.
1.5 L2TP Your ISP requires you to use a Layer Two Tunneling Protocol (L2TP) connection.
1.6 Telstra Big Pond This Protocol is only used for Australia’s ISP connection.
Click on one of the WAN types and then proceed to the manual’s relevant sub-section. Click on Back to return to the
previous screen.

6
1.1 Cable Modem
Choose Cable Modem if your ISP automatically gives you an IP address. Some ISP’s may also require that you fill in
additional information such as Host Name and MAC address (see screen below).
Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require
these settings for you to connect to the Internet.
Parameters Description
Host Name If your ISP requires a Host Name, type in the host name provided by your ISP,
otherwise leave it blank.
MAC Address Your ISP may require a particular MAC address in order for you to connect to the
Internet. This MAC address is the PC’s MAC address that your ISP had originally
connected your Internet connection to. Type in this MAC address in this section or
use the Clone MAC Address button to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button
to work).
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration
for the Cable Modem connection. Your router is now ready to be used.
1.2 Fixed-IP xDSL
Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. Your ISP should provide all the
information required in this section.
Parameters Description
IP Address Assigned This is the IP address that your ISP has given you.
Subnet Mask Enter the Subnet Mask provided by your ISP
(e.g. 255.255.255.0)

7
DNS Address This is the ISP’s DNS server IP address
Service Provider Gateway This is the ISP’s IP address gateway
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration
for the Fixed-IPx DSL connection. Your router is now ready to be used.
1.3 PPPoE
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
Parameter Description
User Name Enter the User Name provided by your ISP for the PPPoE connection.
Password Enter the Password provided by your ISP for the PPPoE connection.
Service Name This is optional. Enter the Service name should your ISP require it, otherwise leave
this field blank.
MTU This is optional. You can specify the maximum size of your transmission packet to the
Internet. Accept the default if you do not wish to set a maximum packet size.
Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line
breaks down and links again, the router will auto-reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP when
someone wants to use the Internet and will remain connected until the WAN idle
timeout is reached.
If you select “Manual”, the router will connect to the ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnect due to the idle timeout feature. If the WAN line breaks down and latter
links again, the router will not auto-connect to the ISP.
Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means if no
packets have been sent during the specified period (no one is using the Internet), the
router will automatically disconnect the connection with your ISP.
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration
for the PPPoE connection. Your router is now ready to be used.

8
1.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
Parameter Description
Obtain an IP address Select this option if the ISP requires you to obtain an IP address by DHCP
automatically before connecting to the PPTP server.
MAC Address Your ISP may require a particular MAC address in order for you to connect to the
Internet. This MAC address is the PC's MAC address that your ISP had originally
connected your Internet connection to. Type in this MAC address in this section or
use the "Clone MAC Address" button to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button
to work).
Use the following IP address Select this option if your ISP requires a static IP address.
IP Address This is the IP address that your ISP has given you to
establish a PPTP connection.
Subnet Mask Enter the Subnet Mask provided by your ISP.
(e.g. 255.255.255.0)
Gateway Enter the IP address of the ISP Gateway.
User ID Enter the User Name provided by your ISP for the PPTP connection. Sometimes
called a Connection ID.
Password Enter the Password provided by your ISP for the PPTP connection.
PPTP Gateway If your LAN has a PPTP gateway, then enter that PPTP gateway IP address here. If
you do not have a PPTP gateway, then enter the ISP’s Gateway IP address above.
Connection ID This is the ID given by your ISP. This is optional.
BEZEQ-ISRAEL Select this item if you are using the service provided by BEZEQ in Israel.
Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line
breaks down and links again, the router will auto-reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP when
someone wants to use the Internet and will remain connected until the WAN idle
timeout is reached.
If you select “Manual”, the router will connect to the ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnect due to the idle timeout feature. If the WAN line breaks down and latter
links again, the router will not auto-connect to the ISP.

9
Idle Time Out You can specify an idle time threshold (minutes) for the WAN port. This means if no
packets have been sent during the specified period (no one using the Internet), then
the router will automatically disconnect the connection with your ISP.
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration
for the PPTP connection. Your router is now ready to be used.
1.5 L2TP
Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
Parameter Description
Obtain an IP address Select this option if the ISP requires you to obtain an IP address by DHCP
automatically before connecting to the L2TP server.
MAC Address Your ISP may require a particular MAC address in order for you to connect to the
Internet. This MAC address is the PC's MAC address that your ISP had originally
connected your Internet connection to. Type in this MAC address in this section or
use the "Clone MAC Address" button to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button
to work).
Use the following IP address Select this option if your ISP requires a static IP address to be used to connect to the
L2TP server.
IP Address This is the IP address that your ISP has given you to establish a L2TP connection.
Subnet Mask Enter the Subnet Mask provided by your ISP.
(e.g. 255.255.255.0)
Gateway Enter the IP address of the ISP Gateway.
User ID Enter the User Name provided by your ISP for the L2TP connection. Sometimes
called a Connection ID.
Password Enter the Password provided by your ISP for the L2TP connection.
L2TP Gateway If your LAN has a L2TP gateway, then enter that L2TP gateway IP address here. If
you do not have a L2TP gateway, then enter the ISP’s Gateway IP address above.
MTU This is optional. You can specify the maximum size of your transmission packet to the
Internet. Accept the default if you do not wish to set a maximum packet size.
Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line
breaks down and links again, the router will auto-reconnect to the ISP.