comwave 506N User manual

506N Installation Guide
Internet

Package Contents
2.
COMWAVE 506N
INTERNET MODEM
ETHERNET CABLE
POWER ADAPTER
OUTPUT: 12V
TELEPHONE CORD
2 x INTERNET FILTER
1
2
3
4
DSL
LAN
DC 12V
Switch
Used to connect your Internet Modem to your
Internet Line using the Telephone Cord supplied.
Used to connect to your computer using the
Ethernet Cable supplied.
Used to connect to a power source using the
Power Adapter supplied.
Used to power the Internet Modem on or o.
2341
Package Contents

3.
LED Light Indicators
Note: The example above shows LAN1
indicator lit. This may be dierent depending
on the LAN port you plug in.
Please follow the step-by-step instructions
on the following pages.
Upon completion of set up, the following
LED lights should be on.

Package Contents
4.
Installation Diagram
Continue to 1
step
Power Bar
with Surge Protector
Comwave
VoIP Adapter
Telephone
Internet
Modem
Computer
7
step
6
step
Phone Jack
Internet
Line
2
step
5
step
4
step

5.
Installation Step-by-Step
1
step To begin installation, shut down your computer.
2
step Connect the Comwave Internet Modem using the supplied telephone cord
to the phone jack.
3
step Connect the supplied Ethernet Cable from the LAN port of the Comwave
Internet Modem to your computer.
4
step (For Home Phone) Connect the supplied Ethernet cable from the LAN port of
your Comwave Internet Modem to the WAN port of the Home Phone Adapter.
5
step Connect the Comwave Internet Modem to a power outlet.
Note: Please allow up to 5 minutes for your modem to be operational.
6
step (For Home Phone) Connect a telephone to the PHONE 1 port on the Home
Phone Adapter. Then connect power to the Home Phone Adapter and wait
5 minutes for a dial-tone. DO NOT DISCONNECT POWER as it may damage
the Home Phone Adapter.
7
step Start your computer. You should be able to browse the Internet instantly.
Can’t Access
the Internet?
1Unplug the power to your
Comwave Internet modem,
home phone adapter and
shut down your computer.
2Wait 30 seconds and then
plug your Comwave Internet
modem’s power cord back
into the power outlet.
3Wait until the LED light
indicators on your Comwave
Internet modem indicate the
modem is operational. This
may take up to 5 minutes.
4Start your computer and
plug in the home phone
adaptor into a power outlet.
5Open your browser and start
surng the Internet. Check
for a dial tone.
Still unable to surf the Internet?
Call us at 1-866-210-9149.
WE’LL GET YOU BACK UP ONLINE!

6.
Wi-Fi Settings Step-by-Step
To log into your Wi-Fi, use the default login information found
on the bottom of your modem.
To change your default Wi-Fi Username and Password make sure
your computer is connected to your Internet Modem before
you begin.
CAUTION
Your Comwave Internet
Modem is already Wi-Fi enabled
by Comwave. We do not
recommend making any changes
to the default settings. Only
advanced users should attempt
to make changes or shut o the
Wi-Fi settings by following
the steps below.

7.
Advanced Wi-Fi Settings
1
step Open your internet browser and
type http://192.168.17.1 in the
address bar.
2
step
Enter your Username and
Password and click LOGIN to
proceed.
3
step
Click on Wi-Fi in the local network
on left as shown in gure
3
step .
4
step
Use caution when making any
changes.
5
step Click Save.
2
step
3
step
4
step
For advanced users wishing to change their network name
and/or password, follow the steps below.
5
step

Need more help?
1-866-210-9149
506N Installation Guide