Conbrov T10 User manual

Photo Frame Camera
Large Capacity Camera Series
- Please ensure that you read the entire Photo Frame
Camera User Manual carefully before using any part
of the product.
- Keep this User Manual for future reference in case of
operational difficulties.
User Manual
Model: T10

General overview
2
Main features:
- This Photo Frame Camera is the world's first 2-year large
capacity battery motion unit.
- You can easily change the picture in the frame at size of
13*18CM or 5.12 x 7.09 in.
- The Photo Frame Camera is super slim - only 14mm
(0.55in) thick.
- Hidden PIR, Lens, LED, USB switcher and buttons make
the Photo Frame Cameral look like any typical photo frame.
- Conbrov's Starlight Technology uses invisible LEDs to
detect and record motion up to 5-8 meters or up to 15-25 ft
in total darkness.
- Privacy protection lets you choose to record video with or
without audio by easily switching the audio button ON or
OFF.
- The Photo Frame Camera can be hung on a wall using the
screws provided or it can sit on a shelf for placement where
you prefer.
Important Reminders:
- Please read the entire User Manual before using the
Photo Frame Camera.
- Please test the position/angle of the Photo Frame
Camera by recording and playing back a video in
advance of selecting a final location to make sure the
camera captures the area you want.
- Please DO NOT use this camera for illegal purpose. It is
important to follow the laws in your region.
- Conbrov is not responsible for missing any video
recording due to incorrect operation, Micro-SD
malfunctions or you're exceeding the Camera's viewing
limitations.

Quick Start to use the camera
1.Use the blue ribbon to carefully remove the Photo Frame
Camera's front cover to change the photo, charge the
battery and install the Micro-SD card.
3
Indicator: Blue light and red LED lights turn on and then
the blue light goes off. The red LED flashes 3 times and
goes off. The red LED light will then stay on.
2.With the photo removed, press MD button directly and it
will enter PIR motion activated mode.

Quick Start to Use the Camera
3.Or hold down the Power button to power On the camera and
then press the REC button to start recording manually and
continuously.
Note:
- While using the Camera, it should be placed in a
horizontal position to shoot objects or people in front of
the Camera.
- With the Camera in PIR motion detection mode, each
time you press the button, there will be about 1.8
seconds delay to start video recording.
- Avoid using the Camera in extreme temperatures.
Doing so will reduce motion detection accuracy.
Indicator: Blue LED stays on when you power On the
camera.
Indicator: Blue LED flashes and then goes Off when
the camera is in recording.
4.You can select audio ON or OFF when you start to
record your video.
4

Camera Structure and Button Function
5
Camera lens
LED PIR
Hole For Wall
Desk Bracket

How to Install and Remove the Micro-SD card
Installing the Micro-SD card: Please insert the Micro-SD
card correctly into the Camera card slot. The Micro-SD
card must be in the slot to record video and audio.
Removing the Micro-SD card: Please use your fingernail
to push the card slightly into the slot until it “sets”. When
you want to remove the Micro-SD card, use your fingernail
again to lightly push in on the card and then the card will
pop out automatically.
DO NOT remove the Micro-SD when the camera is either
powered On or when it is connected to a computer. This
can cause damage to the Micro-SD or the entire camera.
Taking Micro-SD out
Inserting Micro-SD card
6
Special Notes:
- The Camera can record video ONLY when the Micro-SD
is installed.
- DO NOT remove the Micro-SD when the camera is either
powered On or when connected to a computer. This can
cause damage to Micro-SD or the entire camera.
- Please ensure that minimal effort is applied to the
Micro-SD when installing or removing it from the Camera.
Use of force can easily damage the Micro-SD or the
product parts.
- Before using the product for the first time, ensure that the
Micro-SD is formatted. Please check for any saved data
in the Micro-SD to avoid unexpected loss.
We are not liable or responsible for malfunctions that
result from failure to follow the guidelines above.

Charging Information
- It is recommended you charge the Photo Frame Camera
using a 2A USB power adaptor (not supplied) with the USB
cable provided in the package.
- When the battery capacity is low, the Camera cannot be
powered on, or the red and blue LED indicator will flash for
10 seconds and then Camera powers off.
- During charging, the yellow LED indicator will stay On. Once
it is fully charged, the yellow indicator will go Off.
7
1.Charging using the adapter
2.Charging the Camera with a PC.
It is recommended you turn Off the Camera during charging.
During charging, the yellow LED indicator will stay on. Once it
is fully charged, the yellow LED indicator will go Off.

Charging Information
3. Connect with your PC as a U-disk
Please turn on the Camera first, then connect the Camera to
your computer via the USB cable.
The yellow and blue LED indicators will stay on, the
red LED indicator will flash.
Camera angle
75
Detection angle
60
5-8 meters
Detection Angle Capabilities
8

Step 1: Power the Camera On and connect it to a computer
via the provided USB cable. Please wait for a few seconds
and you will see a removable disk open on your computer.
Then open the SETTIME.TXT file.
Time and Date Setting
9
SETTIME.TXT
file Edit Format View Help
File name
yyyy-mm-dd,hh:mm:ss 2016-07-15,
yes
23:15:12
SETTIME.TXT
Step 2: Please change the numbers/letters as needed.
Step 3: Disconnect the Camera from the computer and
power the Camera On it to start recording. The time
settings are done and you will find time&date watermark
in the video recordings.
yes:auto-recycle the SD
no:no auto-recycling
SPECIAL NOTES:
- Please remember to SAVE the file you recorded before
exiting or the change will not be saved.
- Please do not add any blank space or characters to
change the existing file format.

4. Should the Camera power Off automatically, there are two
reasons:
A: The power is too low and you need to recharge the camera.
B: There is no Micro-SD memory card installed or the memory
card is full when the Camera set to no loop recording.
Important Notes:
1. If you didn't find the SETTIME.TXT. file when you open
the Micro-SD card from your computer, please record a
video clip using the Camera to activate the card and
then try to set the date and time again.
2. The amended date and time will not change unless the
battery loses its charge for a long time.
3. Should your Camera malfunction, using a toothpick or
the reset pin provided with the Camera to hold down the
reset button to reset the Camera.
10
Operation guide

Indicator Status and Meanings
Power On
(Push and hold the power button
for 2 seconds)
Normally the blue LED indicator will
stay on.
If no Micro-SD, the blue LED will flash
for 10 seconds and then it powers off.
The Camera powers Off after 60
seconds if there is no any operation.
Record continuously
(Press REC after powered On)
Press REC, the blue LED indicator
will automatically record for 10
minutes per record file. Or press
REC again, the blue LED will be on
to save the present video and stop
recording.
MD
(Press MD after powered on)
Red LED indicator always on.
When there are people moving, the
blue LED indicator will turn On and
then goes Off. The red light flashes
and goes Off (the first red light will
stay On) Now the Camera will record
the present motion and save a video
to the Micro-SD card.
Press MD again, the blue and red
LEDs will flash and go off. The
Camera will save present video, quit
MD and power off.
Charging using 2A USB adaptor
The yellow LED will stay On during
charging; once full charged, it will
go Off.
Power Off
(By pressing the power button)
The red and blue LED will be On for
2 seconds and the Camera powers
Off.
11

ParameterItem
size
Product net weight 410g
Battery LiPo
Stand-by power consumption 10uA
PIR detection angle 60 degrees
PIR detection distance 5-8 meters
Camera angle about 75 degrees
Max PIR stand-by time 2 years
Day time recording power consumption 220mA
Max day time recoridng time a b out 30 hours
Night vision recording power consumption 820mA
Max night vision continuously recording time 9-10 hours
a b out 20 hours by 2A USB power
Full-Charging time adaptor
Resolution 720P
FPS 30FPS
PIR MD video record about 1 minute per file
Record continuously about 10 minutes per file
Max SD storage 32GB
Loop recording optional
2 4.5*19.5*1.4CM
Detailed parameters
12

Pho to Frame Cam e r
Huge b at tery camera s er ies
Pl ea se en sur e th at yo u r ea d the c om p le te u ser m an ual
ca ref ul ly be fo re us ing a ny p art o f the p ro d uc t.
- Ke ep th is co py s a fe f or fu tur e re fer en ce in c ase o f
op era ti ona l di ff i cu lt ies .
-
User Manual
Important notice:
If there is anything missing, please contact us
immediately at www.conbrov.com
Product accessories
Camera Manual USB cable
Warning sticker Card reader Screws
13

Questions & Answers
1-Why does the Camera not have night vision?
The Camera's sensor detects the current environment. if you turn
on the Camera and the light is higher than 20lux, then the sensor
will test the current ambient light. The video will turn to color.
Otherwise, the video will turn to black and white.
If the light is higher than 20lux during recording, and you enter into
a room that the light around is lower than 20lux, the night vision is
not working.
2-How long does the Camera record to a 32GB Micro-SD card?
In generally, it takes about 4.5 hours to filled the 32GB card.
3-Does the Camera support recording during charging?
Yes, the Camera support recording during charging.
4-Why is my Camera not being recognized on the computer?
Please turn on the Camera first, then connect the Camera to the
computer via USB cable. (The blue LED indicator will stay on and
the red indicator will flash.)
5-Why can't I playback the video on the computer?
If you use a Mac, please try a VLC player.
If you use a Windows computer, please try KMPlayer.
Sometimes, it is the problem of the media player.
6-Why does my video have no audio?
Please check that the audio button is turned On when you are
recording.
If yes and you still have no audio, please change the media
player and try it. (See question number 5.)
14
Trouble shooting:
If the Camera is frozen, please reset the Camera by poking the
small reset hole for a couple seconds until the Camera turns Off.

Email: [e-mail]
Website: www.conbrov.com