Confidence Fitness Pro Exercise Bike V2 User manual

Pro Exercise Bike V2
USER’S MANUAL

1
Safety Instructions
Please read this manual carefully before commencing assembly or using the Confidence Pro
ExerciseBike V2
Before starting any exercise programmeyou should consult your doctor. Incorrect or
excessive training canbe dangerous.
Regularly checkall moving parts for obvious signs of wear and tear or damage.
Whencleaning the Confidence Pro ExerciseBike V2 only ever use a damp cloth, never
use solvent cleaners. If you are in any doubt, do not use your product, and contact
Shop247 CustomerService for advice.
Before use always ensure that the Confidence Pro Exercise Bike V2 is positioned on a
solid flat surface.If necessary,use a rubber matunderneath to reduce the possibility of
slipping whilst in use.
Always wearappropriate clothing andfootwearwhen exercising.Donot wearloosefitting
clothes that could become caught or trapped during exercise.
Make sure hair is tied back and kept away from moving parts.
Do not wear any loose jewellery when using the Spin Bike
The Confidence Pro ExerciseBike V2 is for personal use only.
The Confidence Pro ExerciseBike V2 is for indoor use only.
Ensure the Confidence Pro Exercise Bike V2 is stored in a dustfree and dry area.
Maximum User Weight –110kgs
Follow the assemblyinstructions carefully
Before first use, and every 1-2 months checkthat all connecting parts are still tightly
secured.
Inspect the bike every 1-2 months to checkthat all parts are still secureand in good
working condition.
The original packing should be kept in case the Bike needs to be returned for
maintenance or repair.
Keep children away from the Confidence Pro Exercise Bike V2 at all times

2
Parts Diagram

3
PARTSLIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Main Frame
Rear Stabilizer
KeyHead Bolt(M8*40)
Adjusting Knob
Hex nut(M10)
Cap
flat gasket
DomedNuts(M8)
Bushing
VerticalSeat Post
Adjusting Knob
Horizontal Seat Post
Seat
Front Stabilizer
Pedal(L+R)
Fixing Bolt(M4*16)
Slice
Side Panels(L+R)
locknut (M8)
Adjusting Bolt(M6)
1
1
4
4
4
4
4
4
1
1
1
1
1
1
2
10
1
2
2
2
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Round Washer
Fly Wheel
Hex nut(M6)
Brake Set
Bolt(M5*30)
Bushing
UpperSensorWire
Handler Bar
Computersupporter
Computer
U frame
WaterBottle Cage
Braking forceadjustmentpole
WaterBottle
Stretching Knob
Crank Set(L+R)
4
1
4
1
2
1
1
1
1
1
1
1
1
1
2
2

4
Assembly Instructions
STEP 1
Attach the rear stabilizer (2)
to the main frame (1) using
two of the domed nuts (8),
flat gasket (7) and M8
key-head bolts (3).
The front stabilizer is fixed
the same as the rear
stabilizer
STEP2
Slide the seat post 10) into
the seat post stem. You will
have to slacken the knurled
section of the Stretching
Knob (35) and pull the knob
back then lock a suitable
hole for height. Release the
knob and retighten the
knurled portion.
STEP 3
Slide the horizontal
seat post (12) into
position using the
Adjusting Knob
(11).Tap the
Vertical Seat Post
(10) into the end of
the fabrication.

5
STEP 4
Join the Upper sensor wire
(27) to the mating sensor
wire which protrudes from
the top of the main frame.
Slacken the Stretching Knob
by the knurled section by
hand and pull the knob back
placing the handlebar (28)
into the required position in
the main frame.
STEP 5
Mount the computer holder
(29) in a suitable position on
the handlebar. Slide the
computer (30) onto the holder
and connect the computer
lead to the upper sensor wire
(27) which is protruding from
the handlebar post.

6
STEP 6
Mount the water bottle
cage (32) to the
mainframe using the 2
screws (16) and fit the
water bottle (34).
STEP 7
The pedals (15) are marked
“L” and “R”-leftand right.
Connect them to their
appropriate crank set (36).
The right crank set is on the
right hand side of the cycle
as you sit on it.
Note: The Right pedal
should be threaded
clockwise and the left
pedal anti-clockwise

7
Adjusting the Seat
The seat height can be adjusted by removing the adjustment knob and raising or lowering
the seat. There are holes in the seat post allowing for a range of heights. Once the correct
height has been chosen, refit the adjustment knob and tighten. The tension control knob
allows you to alter the resistance of the pedals. Ahigh resistance makes it more difficult to
pedal, a low resistance makes it easier. For the best results set the tension while the bike is
in use.
Using the Computer
Auto on/off–Auto start/stop
The computer will turn on automatically once you press the key or
start exercising. If there’s no movement for 8 minutes, the
computerwill turn off automatically.
Functionkeys
MODE: Press this key to selectfunctions.
RESET: Press this key for 3 seconds to reset the functions Time, Distance
and Calories.

8
Functions
1. Time:Displays the workout time.
2. Speed: Displays the current speed.
3. Distance:Displays the distance cycledduring the workout
4. Calories: Counts the calories usedduring the workout
5. Scan: Automatically scans through each function every 4 seconds
FUNCTION
Visualization
(SCAN)
Press key MODE until appears “ ” into
SCAN position, then the functions Time,
Distance, Calories and Total Distance will
rotate every 4 seconds.
TIME
Counts the exercise total time from 0:00 to
99:59(M:S)
Current speed
(SPEED)
Displays the current speed from 0 to 99.9
km/h or mph (or 1500 RPM)
Trip distance (DIST)
Counts the exercise distance from 0.00 to
99.99 Km or Miles
CALORIES
Counts the calories used from 0.0 to 999.9
Cal or 0 to 9999 Kcal
Total Distance
(TOTAL DIST)
Counts the total distance from 0 to 9999 Km
or Miles after the batteries have been
installed
Battery type
2 batteries AA or UM-3
Operating Temperate
0°C to+40°C (32°F to 104°F)
Storage Temperature
-10°C to +60°C (14°F to 168°F)
If the screen is blank on the computer, please check all the connections are correct and
secure