TOORX BRX85 User manual

Ed : 02/17
INSTRUCTION
Rev : 0000

4

ASSEMBLY INSTRUCTIONS
Step 1
Assem ly the rear and front sta ilizer (N&M)
with 4 olts (M-1).
Step 2
Assem le the left hand pedal (K-L) and the
right hand pedal (K-R) to the crank.
Step 3
Pass through the handle ar post (C) from
the plastic cover (I-1).
Connect the computer ca le up and down
(C-5&E-4), connect the tension control up
and down (C-6&E-9). Fix the handle ar post
to the main frame after the a ove two steps.
Fasten those screws （E-2） and washers
(E-3&E-8) to fix the handle ar post, move
the plastic cover to right position.
5

ASSEMBLY INSTRUCTIONS
Step 4
Attach the handle ar (B) to the handle ar
post etween the steel covers, secure the
steel cover assem ly using one handle ar
cover (C-7), one flat washer (C-1), one
spring washer (C-2), one ushing (C-3) and
one kno (C-4).
Step 5
Plug in the ca les (A-1&C-5) and (A-2&B-2)
etween the computer and the handle ar
post.
Fix the computer onto the handle ar post
with four screws (A-3).
6

ASSEMBLY INSTRUCTIONS
Step 6
Insert the seat post (D) into the main frame
through the plastic sleeve. Select the ideal
hole position on the seat post. Insert the kno
(E-6) into the hole. Tighten fully the kno .
Step 7
Connect the saddle (D-6) and the slider (D-
5) .
Attach the slider onto the top of the seat
post and the secure using the horizontal
adjusting kno (D-1) and one flat washer (D-
2).
7

PARTS LIST
Item Description Q’ty Item Description Q’ty
A Computer 1 F-7 C-circle 1
A-1 Pulse ca le (upper) 1 G Idle 1
A-2 Motor ca le 2 G-1 Nylon nut M8 2
A-3 Screw M5*10 4 G-2 Bushing Φ10*Φ14*6L 2
B Handle ar 1 G-3 Idle wheel 1
B-1 Screw M4*20 2 G-4 Flat washer 2
B-2 Pulse ca le (lower) 2 G-5 Screw M8*20L 1
B-3 End cap 2 G-6 Spring 1
B-4 Foam grip 2 H Flywheel 1
B-5 Hand pulse 2 H-1 Screw 3/8″-26 5
C Handle ar post 1 H-2 Bearing 6000 1
C-1 Flat washer 1 H-3 Bearing 6300 1
C-2 Spring washer 1 H-4 One way earing 1
C-3 Bushing 1 H-5 Bearing 6203 1
C-4 Kno 1 H-6 Small elt pulley 1
C-5 Sensor ca le 1 H-7 Bearing 6003 1
C-6 Tension control 1 H-8 Mandril of flywheel 1
C-7 Handle ar cover 1 I-L Chain cover (left) 1
I-R Chain cover (right) 1
I-1 Handle ar post cover 1
D Seat post 1 I-2 Screw M4*20 5
D-1 Seat kno 1 I-3 Screw 12
D-2 Flat washer 1 I-4 Rear tu e cover 1
D-3 Cap 20*40 2 J-L Crank (left) 1
D-4 Slider fixed screw 1 J-R Crank (right) 1
D-5 Slider 1 J-1 Screw M8 2
D-6 Saddle 1 J-2 Cover for crank 2
K-L Pedal (left) 1
K-R Pedal (right) 1
L Magnetic set 1
E Main frame 1 L-1 Screw M6 2
E-1 Bearing 6203 2 L-2 Spring 1
E-2 Screw M8*16L 5 L-3 Magnetic 10
E-3 Flat washer 4 L-4 Bushing 1
E-4 Sensor ca le (lower) 1 L-5 Wave washer 2
E-5 Plastic sleeve 1 L-6 C circle 2
8

E-6 Seat post kno M16 1 L-7 Spring washer 2
E-7 Screw 1 L-8 Flat washer 2
E-8 Semicircle washer 1 M Front sta ilizer 1
E-9 Tension ca le (lower) 1 M-L Front end cap (left) 1
F Plastic pulley 1 M-R Front end cap (right) 1
F-1 Bushing Φ17*5T 1 M-1 Screw M8*60L 4
F-2 Axle assem ly 1 N Rear sta ilizer 1
F-3 Screw M8*10L 3 N-L Rear end cap (left) 1
F-4 Belt 1 N-R Rear end cap(right) 1
F-5 Wave washer 1 O Inner hex. wrench 1
F-6 Flat washer 1 P Harpoon wrench 1
9

COMPLETE BIKE ASSEMBLY
Exercise Computer
10

SPECIFICATIONS:
TIME--------------------------------------------------00:00 - 99:59 MIN:SEC
SPEED-------------------------------------------------0.0 – 999.9 KM/H OR ML/H
DISTANCE----------------------------------------------0.00 – 99.99 KM OR ML
CALORIES----------------------------------------------0.0 – 999.9 KCAL
ODOMETER(if have)-------------------------------------0.00 – 99.99 KM OR ML
PULSE(if have)----------------------------------------40 - 200 BEATS/MIN
KEY FUNCTION:
MODE/SELECT: To select the function you want. Hold the key for 4 seconds to
have all function values reset except the ODOMETER(TOTAL).
SET(if have): To input the target value y the key except the ODOMETER(TOTAL).
RESET/CLEAR(if have): To let the value reset except the ODOMETER(TOTAL).
OPERATION PROCEDURES:
AUTO ON/OFF .The monitor will e automatically shut off if there is no signal
coming in for 4 minutes. The monitor will e auto-powered when
start exercise or press the key.
FUNCTION:
<1>.TIME(TMR) Auto-memorize the workout time while exercising.
<2>.SPEED(SPD) Display the current speed.
<3>.DISTANCE(DST) Accumulate the distances while exercising.
<4>.CALORIES(CAL) Auto-memorize calories amount consumed while exercising.
<5>.ODOMETER(TOTAL) (if have) Display the total distances while exercising.
When the signal input, it start the value up on the original data.
The ODOMETER can’t e reset( y any key)except you replace attery once.
<6>.PULSE(PUL) (if have). Display the user’s heart rate per minute while
exercising. Remark: You have to hold on reaction planks with oth hands.
<7>.SCAN Automatically scan through each function etween ①TIME②SPEED(if
have)③DISTANCE④CALORIES⑤PULSE(if have)⑥ODOMETER(if have).
BATTERY If there is a possi ility to see an improper display on the monitor, please
replace the atteries to have a good result. This monitor uses two “AA”or one“AAA”
attery or one“1.5V” utton attery. You can replace the atteries at the same time.
11

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]